| /linux-2.4.37.9/drivers/s390/char/ |
| D | tape3480.c | 91 tape3480_shutdown (int autoprobe) { in tape3480_shutdown() argument
92 if (autoprobe) in tape3480_shutdown()
97 tape3480_init (int autoprobe) in tape3480_init() argument
150 if (autoprobe) in tape3480_init()
|
| D | tape3490.c | 90 tape3490_shutdown (int autoprobe) { in tape3490_shutdown() argument
91 if (autoprobe) in tape3490_shutdown()
97 tape3490_init (int autoprobe) in tape3490_init() argument
150 if (autoprobe) in tape3490_init()
|
| /linux-2.4.37.9/drivers/block/paride/ |
| D | paride.c | 337 int pi_init(PIA *pi, int autoprobe, int port, int mode, in pi_init() argument
349 if (autoprobe) { in pi_init()
391 if (autoprobe) printk("%s: Autoprobe failed\n",device); in pi_init()
|
| D | paride.h | 65 int autoprobe, /* 1 to autoprobe */
|
| /linux-2.4.37.9/Documentation/ |
| D | parport.txt | 103 | |-- autoprobe
118 |-- autoprobe
169 autoprobe Any IEEE-1284 device ID information that has been
172 autoprobe[0-3] IEEE 1284 device ID information retrieved from
|
| D | specialix.txt | 378 - This is a difficult card to autoprobe.
|
| D | paride.txt | 208 you have connected. By default, each driver will autoprobe for a single
|
| D | Configure.help | 5944 appear in /proc/sys/dev/parport/*/autoprobe*. It is safe to say N.
22234 Verbose soundcard initialization -- affects the format of autoprobe
29404 # LocalWords: HDM's OSM's lan FibreChannel ECP autoprobe itg lbl ipmasq cjb IC
|
| /linux-2.4.37.9/drivers/acorn/block/ |
| D | fd1772.c | 210 int autoprobe; /* !=0 : do autoprobe */ member
967 if (unit[SelectedDrive].autoprobe) { in fd_rwsec_done()
1256 floppy->autoprobe = 1; in redo_fd_request()
1268 floppy->autoprobe = 0; in redo_fd_request()
|
| /linux-2.4.37.9/Documentation/networking/ |
| D | 3c505.txt | 13 If no base address is given at boot time, the driver will autoprobe
|
| D | net-modules.txt | 28 If you are adventurous, you can ask the driver to autoprobe
58 about autoprobing being not recommended, and begrudgingly autoprobe for
68 argument passed in via insmod. It will refuse to autoprobe.
|
| D | ltpc.txt | 11 While the driver will attempt to autoprobe the I/O port address, IRQ
|
| D | arcnet.txt | 127 chipset driver which will autoprobe if not told where the card is.
134 To disable the autoprobe, just specify "com90xx=" on the kernel command line.
135 To specify the name alone, but allow autoprobe, just put "com90xx=<name>"
518 Starting with v2.40 ALPHA, the autoprobe routines have changed
|
| D | de4x5.txt | 50 achieved by letting the driver autoprobe as if it were compiled into the
|
| /linux-2.4.37.9/drivers/block/ |
| D | ataflop.c | 226 int autoprobe; /* !=0 : do autoprobe */ member
1105 if (SUD.autoprobe) { in fd_rwsec_done1()
1489 UD.autoprobe = 1; in redo_fd_request()
1507 UD.autoprobe = 0; in redo_fd_request()
|
| /linux-2.4.37.9/Documentation/video4linux/ |
| D | CQcam.txt | 45 CONFIG_PNP_PARPORT M for autoprobe.o IEEE1284 readback module
135 cat /proc/parport/PORTNUMBER/autoprobe
160 grep ^ /proc/parport/?/autoprobe
|
| /linux-2.4.37.9/drivers/scsi/ |
| D | README.g_NCR5380 | 58 (255 should be specified for no or DMA interrupt, 254 to autoprobe for an
|
| /linux-2.4.37.9/drivers/ide/ |
| D | ide-probe.c | 375 int autoprobe = 0; in try_to_identify() local
379 autoprobe = 1; in try_to_identify()
387 if (autoprobe) { in try_to_identify()
|
| /linux-2.4.37.9/Documentation/isdn/ |
| D | README.act2000 | 52 p = portbase (-1 means autoprobe)
|
| /linux-2.4.37.9/Documentation/filesystems/ |
| D | proc.txt | 556 autoprobe Any IEEE-1284 device ID information that has been acquired.
|