Searched refs:BIT_3 (Results 1 – 5 of 5) sorted by relevance
52 #define CB_CFIG_TERMCL_EN BIT_3 /* Cache line write */67 #define CB_CFIG_CI_INT BIT_3 /* Command Complete Interrupt */85 #define CB_CFIG_NO_SRCADR BIT_3 /* No Source Address Insertion */126 #define CB_CFIG_FC_RESTOP BIT_3 /* Rx Flow Control Restop */140 #define CB_CFIG_MULTICAST_ALL BIT_3 /* Multicast All */146 #define CB_CFIG_LONG_RX_OK BIT_3
177 #define BIT_3 0x0008 macro264 #define SCB_RUS_NO_RESOURCES BIT_3 /* RU Out Of Resources */267 #define SCB_RUS_NO_RBDS (BIT_3 | BIT_5) /* RU No More RBDs */300 #define SCB_ER_INT_MASK BIT_3 /* Early Receive */365 #define CB_TX_SF_BIT BIT_3 /* TX CB Flexible Mode */401 #define RFD_SF_BIT BIT_3 /* RFD Flexible Mode */419 #define CB_SELFTEST_REGISTER_BIT BIT_3459 #define RFD_PARSE_BIT BIT_3
60 #define BIT_3 (1L << 3) macro230 #define PCI_PREFEN BIT_3 /* Prefetchable */296 #define PCI_EN_DUMMY_RD BIT_3 /* Enable Dummy Read */830 #define PC_VAUX_ON BIT_3 /* Switch VAUX On */874 #define IS_XS2_C BIT_3 /* Q_XS2 Encoding Error */896 #define IS_M1_PAR_ERR BIT_3 /* MAC 1 Parity Error */1001 #define GP_IO_3 BIT_3 /* IO_3 pin */1201 #define CSR_IRQ_CL_P BIT_3 /* (Rx) Clear Parity IRQ */1250 #define T2_STEP04 BIT_3 /* Inc AC/Dec BC by 4 */1446 #define GMF_OPER_ON BIT_3 /* Operational Mode On */[all …]
31 #define BIT_3 0x8 macro125 #define SRB_ABORTED BIT_3 /* Command aborted command already */149 #define QLA1280_QSENSE BIT_3 /* Sense data cache valid */179 #define NV_DATA_IN BIT_3569 #define RF_BAD_PAYLOAD BIT_3 /* Bad payload. */967 #define SS_BUSY_CONDITION BIT_3968 #define SS_RESERVE_CONFLICT (BIT_4 | BIT_3)
1669 mr = BIT_3 | BIT_2 | BIT_1 | BIT_0; in qla12160_set_target_parameters()2556 if ((status = qla1280_mailbox_command(ha, BIT_4 | BIT_3 | in qla1280_setup_chip()2574 BIT_4 | BIT_3 | BIT_2 | in qla1280_setup_chip()2670 BIT_3 | BIT_2 | BIT_1 | BIT_0, in qla1280_init_rings()2684 BIT_3 | BIT_2 | BIT_1 | BIT_0, in qla1280_init_rings()2888 WRT_REG_WORD(®->gpio_enable, (BIT_3 + BIT_2 + BIT_1 + BIT_0)); in qla1280_nvram_config()2889 mb[0] = nv->termination.c & (BIT_3 + BIT_2 + BIT_1 + BIT_0); in qla1280_nvram_config()3013 mr |= BIT_3; in qla1280_nvram_config()3663 pkt->control_flags |= cpu_to_le16(BIT_3); in qla1280_64bit_start_scsi()3963 pkt->control_flags |= cpu_to_le16(BIT_3); in qla1280_32bit_start_scsi()[all …]