1// SPDX-License-Identifier: BSD-3-Clause
2/*
3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
4 * Copyright (c) 2019, Linaro Limited
5 */
6
7#include <dt-bindings/input/input.h>
8#include <dt-bindings/interrupt-controller/irq.h>
9#include <dt-bindings/spmi/spmi.h>
10#include <dt-bindings/iio/qcom,spmi-vadc.h>
11
12/ {
13	thermal-zones {
14		pm8150-thermal {
15			polling-delay-passive = <100>;
16			polling-delay = <0>;
17
18			thermal-sensors = <&pm8150_temp>;
19
20			trips {
21				trip0 {
22					temperature = <95000>;
23					hysteresis = <0>;
24					type = "passive";
25				};
26
27				trip1 {
28					temperature = <115000>;
29					hysteresis = <0>;
30					type = "hot";
31				};
32
33				trip2 {
34					temperature = <145000>;
35					hysteresis = <0>;
36					type = "critical";
37				};
38			};
39		};
40	};
41};
42
43&spmi_bus {
44	pm8150_0: pmic@0 {
45		compatible = "qcom,pm8150", "qcom,spmi-pmic";
46		reg = <0x0 SPMI_USID>;
47		#address-cells = <1>;
48		#size-cells = <0>;
49
50		pon: pon@800 {
51			compatible = "qcom,pm8998-pon";
52			reg = <0x0800>;
53			mode-bootloader = <0x2>;
54			mode-recovery = <0x1>;
55
56			pon_pwrkey: pwrkey {
57				compatible = "qcom,pm8941-pwrkey";
58				interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
59				debounce = <15625>;
60				bias-pull-up;
61				linux,code = <KEY_POWER>;
62
63				status = "disabled";
64			};
65
66			pon_resin: resin {
67				compatible = "qcom,pm8941-resin";
68				interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
69				debounce = <15625>;
70				bias-pull-up;
71
72				status = "disabled";
73			};
74		};
75
76		pm8150_temp: temp-alarm@2400 {
77			compatible = "qcom,spmi-temp-alarm";
78			reg = <0x2400>;
79			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
80			io-channels = <&pm8150_adc ADC5_DIE_TEMP>;
81			io-channel-names = "thermal";
82			#thermal-sensor-cells = <0>;
83		};
84
85		pm8150_adc: adc@3100 {
86			compatible = "qcom,spmi-adc5";
87			reg = <0x3100>;
88			#address-cells = <1>;
89			#size-cells = <0>;
90			#io-channel-cells = <1>;
91			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
92
93			ref-gnd@0 {
94				reg = <ADC5_REF_GND>;
95				qcom,pre-scaling = <1 1>;
96				label = "ref_gnd";
97			};
98
99			vref-1p25@1 {
100				reg = <ADC5_1P25VREF>;
101				qcom,pre-scaling = <1 1>;
102				label = "vref_1p25";
103			};
104
105			die-temp@6 {
106				reg = <ADC5_DIE_TEMP>;
107				qcom,pre-scaling = <1 1>;
108				label = "die_temp";
109			};
110		};
111
112		pm8150_adc_tm: adc-tm@3500 {
113			compatible = "qcom,spmi-adc-tm5";
114			reg = <0x3500>;
115			interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
116			#thermal-sensor-cells = <1>;
117			#address-cells = <1>;
118			#size-cells = <0>;
119			status = "disabled";
120		};
121
122		rtc@6000 {
123			compatible = "qcom,pm8941-rtc";
124			reg = <0x6000>;
125			reg-names = "rtc", "alarm";
126			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
127		};
128
129		pm8150_gpios: gpio@c000 {
130			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
131			reg = <0xc000>;
132			gpio-controller;
133			gpio-ranges = <&pm8150_gpios 0 0 10>;
134			#gpio-cells = <2>;
135			interrupt-controller;
136			#interrupt-cells = <2>;
137		};
138	};
139
140	pmic@1 {
141		compatible = "qcom,pm8150", "qcom,spmi-pmic";
142		reg = <0x1 SPMI_USID>;
143		#address-cells = <1>;
144		#size-cells = <0>;
145	};
146};
147