1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * Copyright (C) 2011-2013 Texas Instruments Incorporated - https://www.ti.com/ 4 */ 5#include <dt-bindings/input/input.h> 6#include "elpida_ecb240abacn.dtsi" 7#include "omap4-mcpdm.dtsi" 8 9/ { 10 memory@80000000 { 11 device_type = "memory"; 12 reg = <0x80000000 0x40000000>; /* 1 GB */ 13 }; 14 15 reserved-memory { 16 #address-cells = <1>; 17 #size-cells = <1>; 18 ranges; 19 20 dsp_memory_region: dsp-memory@98000000 { 21 compatible = "shared-dma-pool"; 22 reg = <0x98000000 0x800000>; 23 reusable; 24 status = "okay"; 25 }; 26 27 ipu_memory_region: ipu-memory@98800000 { 28 compatible = "shared-dma-pool"; 29 reg = <0x98800000 0x7000000>; 30 reusable; 31 status = "okay"; 32 }; 33 }; 34 35 chosen { 36 stdout-path = &uart3; 37 }; 38 39 aliases { 40 display0 = &dvi0; 41 display1 = &hdmi0; 42 ethernet = ðernet; 43 }; 44 45 leds: leds { 46 compatible = "gpio-leds"; 47 pinctrl-names = "default"; 48 pinctrl-0 = < 49 &led_wkgpio_pins 50 >; 51 52 led-heartbeat { 53 label = "pandaboard::status1"; 54 gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; 55 linux,default-trigger = "heartbeat"; 56 }; 57 58 led-mmc { 59 label = "pandaboard::status2"; 60 gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; 61 linux,default-trigger = "mmc0"; 62 }; 63 }; 64 65 gpio_keys: gpio_keys { 66 compatible = "gpio-keys"; 67 pinctrl-names = "default"; 68 pinctrl-0 = < 69 &button_pins 70 >; 71 72 buttonS2 { 73 label = "button S2"; 74 gpios = <&gpio4 25 GPIO_ACTIVE_LOW>; /* gpio_121 */ 75 linux,code = <BTN_0>; 76 wakeup-source; 77 }; 78 }; 79 80 sound: sound { 81 compatible = "ti,abe-twl6040"; 82 ti,model = "PandaBoard"; 83 84 ti,mclk-freq = <38400000>; 85 86 ti,mcpdm = <&mcpdm>; 87 88 ti,twl6040 = <&twl6040>; 89 90 /* Audio routing */ 91 ti,audio-routing = 92 "Headset Stereophone", "HSOL", 93 "Headset Stereophone", "HSOR", 94 "Ext Spk", "HFL", 95 "Ext Spk", "HFR", 96 "Line Out", "AUXL", 97 "Line Out", "AUXR", 98 "HSMIC", "Headset Mic", 99 "Headset Mic", "Headset Mic Bias", 100 "AFML", "Line In", 101 "AFMR", "Line In"; 102 }; 103 104 /* HS USB Port 1 Power */ 105 hsusb1_power: hsusb1_power_reg { 106 compatible = "regulator-fixed"; 107 regulator-name = "hsusb1_vbus"; 108 regulator-min-microvolt = <3300000>; 109 regulator-max-microvolt = <3300000>; 110 gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; /* gpio_1 */ 111 startup-delay-us = <70000>; 112 enable-active-high; 113 /* 114 * boot-on is required along with always-on as the 115 * regulator framework doesn't enable the regulator 116 * if boot-on is not there. 117 */ 118 regulator-always-on; 119 regulator-boot-on; 120 }; 121 122 /* HS USB Host PHY on PORT 1 */ 123 hsusb1_phy: hsusb1_phy { 124 compatible = "usb-nop-xceiv"; 125 reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */ 126 #phy-cells = <0>; 127 vcc-supply = <&hsusb1_power>; 128 clocks = <&auxclk3_ck>; 129 clock-names = "main_clk"; 130 clock-frequency = <19200000>; 131 }; 132 133 /* regulator for wl12xx on sdio5 */ 134 wl12xx_vmmc: wl12xx_vmmc { 135 pinctrl-names = "default"; 136 pinctrl-0 = <&wl12xx_gpio>; 137 compatible = "regulator-fixed"; 138 regulator-name = "vwl1271"; 139 regulator-min-microvolt = <1800000>; 140 regulator-max-microvolt = <1800000>; 141 gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>; 142 startup-delay-us = <70000>; 143 enable-active-high; 144 }; 145 146 tfp410: encoder0 { 147 compatible = "ti,tfp410"; 148 powerdown-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* gpio_0 */ 149 150 ports { 151 #address-cells = <1>; 152 #size-cells = <0>; 153 154 port@0 { 155 reg = <0>; 156 157 tfp410_in: endpoint { 158 remote-endpoint = <&dpi_out>; 159 }; 160 }; 161 162 port@1 { 163 reg = <1>; 164 165 tfp410_out: endpoint { 166 remote-endpoint = <&dvi_connector_in>; 167 }; 168 }; 169 }; 170 }; 171 172 dvi0: connector0 { 173 compatible = "dvi-connector"; 174 label = "dvi"; 175 176 digital; 177 178 ddc-i2c-bus = <&i2c3>; 179 180 port { 181 dvi_connector_in: endpoint { 182 remote-endpoint = <&tfp410_out>; 183 }; 184 }; 185 }; 186 187 tpd12s015: encoder1 { 188 compatible = "ti,tpd12s015"; 189 190 gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */ 191 <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */ 192 <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */ 193 194 ports { 195 #address-cells = <1>; 196 #size-cells = <0>; 197 198 port@0 { 199 reg = <0>; 200 201 tpd12s015_in: endpoint { 202 remote-endpoint = <&hdmi_out>; 203 }; 204 }; 205 206 port@1 { 207 reg = <1>; 208 209 tpd12s015_out: endpoint { 210 remote-endpoint = <&hdmi_connector_in>; 211 }; 212 }; 213 }; 214 }; 215 216 hdmi0: connector1 { 217 compatible = "hdmi-connector"; 218 label = "hdmi"; 219 220 type = "a"; 221 222 port { 223 hdmi_connector_in: endpoint { 224 remote-endpoint = <&tpd12s015_out>; 225 }; 226 }; 227 }; 228}; 229 230&omap4_pmx_core { 231 pinctrl-names = "default"; 232 pinctrl-0 = < 233 &dss_dpi_pins 234 &tfp410_pins 235 &dss_hdmi_pins 236 &tpd12s015_pins 237 &hsusbb1_pins 238 >; 239 240 twl6040_pins: twl6040-pins { 241 pinctrl-single,pins = < 242 OMAP4_IOPAD(0x120, PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */ 243 OMAP4_IOPAD(0x1a0, PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */ 244 >; 245 }; 246 247 mcbsp1_pins: mcbsp1-pins { 248 pinctrl-single,pins = < 249 OMAP4_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */ 250 OMAP4_IOPAD(0x100, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */ 251 OMAP4_IOPAD(0x102, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */ 252 OMAP4_IOPAD(0x104, PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */ 253 >; 254 }; 255 256 dss_dpi_pins: dss-dpi-pins { 257 pinctrl-single,pins = < 258 OMAP4_IOPAD(0x162, PIN_OUTPUT | MUX_MODE5) /* dispc2_data23 */ 259 OMAP4_IOPAD(0x164, PIN_OUTPUT | MUX_MODE5) /* dispc2_data22 */ 260 OMAP4_IOPAD(0x166, PIN_OUTPUT | MUX_MODE5) /* dispc2_data21 */ 261 OMAP4_IOPAD(0x168, PIN_OUTPUT | MUX_MODE5) /* dispc2_data20 */ 262 OMAP4_IOPAD(0x16a, PIN_OUTPUT | MUX_MODE5) /* dispc2_data19 */ 263 OMAP4_IOPAD(0x16c, PIN_OUTPUT | MUX_MODE5) /* dispc2_data18 */ 264 OMAP4_IOPAD(0x16e, PIN_OUTPUT | MUX_MODE5) /* dispc2_data15 */ 265 OMAP4_IOPAD(0x170, PIN_OUTPUT | MUX_MODE5) /* dispc2_data14 */ 266 OMAP4_IOPAD(0x172, PIN_OUTPUT | MUX_MODE5) /* dispc2_data13 */ 267 OMAP4_IOPAD(0x174, PIN_OUTPUT | MUX_MODE5) /* dispc2_data12 */ 268 OMAP4_IOPAD(0x176, PIN_OUTPUT | MUX_MODE5) /* dispc2_data11 */ 269 270 OMAP4_IOPAD(0x1b4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data10 */ 271 OMAP4_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data9 */ 272 OMAP4_IOPAD(0x1b8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data16 */ 273 OMAP4_IOPAD(0x1ba, PIN_OUTPUT | MUX_MODE5) /* dispc2_data17 */ 274 OMAP4_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE5) /* dispc2_hsync */ 275 OMAP4_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE5) /* dispc2_pclk */ 276 OMAP4_IOPAD(0x1c0, PIN_OUTPUT | MUX_MODE5) /* dispc2_vsync */ 277 OMAP4_IOPAD(0x1c2, PIN_OUTPUT | MUX_MODE5) /* dispc2_de */ 278 OMAP4_IOPAD(0x1c4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data8 */ 279 OMAP4_IOPAD(0x1c6, PIN_OUTPUT | MUX_MODE5) /* dispc2_data7 */ 280 OMAP4_IOPAD(0x1c8, PIN_OUTPUT | MUX_MODE5) /* dispc2_data6 */ 281 OMAP4_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE5) /* dispc2_data5 */ 282 OMAP4_IOPAD(0x1cc, PIN_OUTPUT | MUX_MODE5) /* dispc2_data4 */ 283 OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE5) /* dispc2_data3 */ 284 285 OMAP4_IOPAD(0x1d0, PIN_OUTPUT | MUX_MODE5) /* dispc2_data2 */ 286 OMAP4_IOPAD(0x1d2, PIN_OUTPUT | MUX_MODE5) /* dispc2_data1 */ 287 OMAP4_IOPAD(0x1d4, PIN_OUTPUT | MUX_MODE5) /* dispc2_data0 */ 288 >; 289 }; 290 291 tfp410_pins: tfp410-pins { 292 pinctrl-single,pins = < 293 OMAP4_IOPAD(0x184, PIN_OUTPUT | MUX_MODE3) /* gpio_0 */ 294 >; 295 }; 296 297 dss_hdmi_pins: dss-hdmi-pins { 298 pinctrl-single,pins = < 299 OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */ 300 OMAP4_IOPAD(0x09c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */ 301 OMAP4_IOPAD(0x09e, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */ 302 >; 303 }; 304 305 tpd12s015_pins: tpd12s015-pins { 306 pinctrl-single,pins = < 307 OMAP4_IOPAD(0x062, PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */ 308 OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */ 309 OMAP4_IOPAD(0x098, PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */ 310 >; 311 }; 312 313 hsusbb1_pins: hsusbb1-pins { 314 pinctrl-single,pins = < 315 OMAP4_IOPAD(0x0c2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */ 316 OMAP4_IOPAD(0x0c4, PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */ 317 OMAP4_IOPAD(0x0c6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */ 318 OMAP4_IOPAD(0x0c8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */ 319 OMAP4_IOPAD(0x0ca, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */ 320 OMAP4_IOPAD(0x0cc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */ 321 OMAP4_IOPAD(0x0ce, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */ 322 OMAP4_IOPAD(0x0d0, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */ 323 OMAP4_IOPAD(0x0d2, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */ 324 OMAP4_IOPAD(0x0d4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */ 325 OMAP4_IOPAD(0x0d6, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */ 326 OMAP4_IOPAD(0x0d8, PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */ 327 >; 328 }; 329 330 i2c1_pins: i2c1-pins { 331 pinctrl-single,pins = < 332 OMAP4_IOPAD(0x122, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ 333 OMAP4_IOPAD(0x124, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ 334 >; 335 }; 336 337 i2c2_pins: i2c2-pins { 338 pinctrl-single,pins = < 339 OMAP4_IOPAD(0x126, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ 340 OMAP4_IOPAD(0x128, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ 341 >; 342 }; 343 344 i2c3_pins: i2c3-pins { 345 pinctrl-single,pins = < 346 OMAP4_IOPAD(0x12a, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ 347 OMAP4_IOPAD(0x12c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ 348 >; 349 }; 350 351 i2c4_pins: i2c4-pins { 352 pinctrl-single,pins = < 353 OMAP4_IOPAD(0x12e, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ 354 OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ 355 >; 356 }; 357 358 /* 359 * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP 360 * REVISIT: Are the pull-ups needed for GPIO 48 and 49? 361 */ 362 wl12xx_gpio: wl12xx-gpio-pins { 363 pinctrl-single,pins = < 364 OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 */ 365 OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3) /* gpmc_a22.gpio_46 */ 366 OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48 */ 367 OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 */ 368 >; 369 }; 370 371 /* wl12xx GPIO inputs and SDIO pins */ 372 wl12xx_pins: wl12xx-pins { 373 pinctrl-single,pins = < 374 OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) /* gpmc_ncs2.gpio_52 */ 375 OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ 376 OMAP4_IOPAD(0x148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk.sdmmc5_clk */ 377 OMAP4_IOPAD(0x14a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_cmd.sdmmc5_cmd */ 378 OMAP4_IOPAD(0x14c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat0.sdmmc5_dat0 */ 379 OMAP4_IOPAD(0x14e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1.sdmmc5_dat1 */ 380 OMAP4_IOPAD(0x150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2.sdmmc5_dat2 */ 381 OMAP4_IOPAD(0x152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3.sdmmc5_dat3 */ 382 >; 383 }; 384 385 button_pins: button-pins { 386 pinctrl-single,pins = < 387 OMAP4_IOPAD(0x114, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_121 */ 388 >; 389 }; 390}; 391 392&omap4_pmx_wkup { 393 led_wkgpio_pins: leds-wkpins-pins { 394 pinctrl-single,pins = < 395 OMAP4_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */ 396 OMAP4_IOPAD(0x05c, PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */ 397 >; 398 }; 399}; 400 401&i2c1 { 402 pinctrl-names = "default"; 403 pinctrl-0 = <&i2c1_pins>; 404 405 clock-frequency = <400000>; 406 407 twl: twl@48 { 408 reg = <0x48>; 409 /* IRQ# = 7 */ 410 interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */ 411 }; 412 413 twl6040: twl@4b { 414 compatible = "ti,twl6040"; 415 #clock-cells = <0>; 416 reg = <0x4b>; 417 418 pinctrl-names = "default"; 419 pinctrl-0 = <&twl6040_pins>; 420 421 /* IRQ# = 119 */ 422 interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ 423 ti,audpwron-gpio = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio line 127 */ 424 425 vio-supply = <&v1v8>; 426 v2v1-supply = <&v2v1>; 427 enable-active-high; 428 }; 429}; 430 431#include "twl6030.dtsi" 432#include "twl6030_omap4.dtsi" 433 434&i2c2 { 435 pinctrl-names = "default"; 436 pinctrl-0 = <&i2c2_pins>; 437 438 clock-frequency = <400000>; 439}; 440 441&i2c3 { 442 pinctrl-names = "default"; 443 pinctrl-0 = <&i2c3_pins>; 444 445 clock-frequency = <100000>; 446 447 /* 448 * Display monitor features are burnt in their EEPROM as EDID data. 449 * The EEPROM is connected as I2C slave device. 450 */ 451 eeprom@50 { 452 compatible = "ti,eeprom"; 453 reg = <0x50>; 454 }; 455}; 456 457&i2c4 { 458 pinctrl-names = "default"; 459 pinctrl-0 = <&i2c4_pins>; 460 461 clock-frequency = <400000>; 462}; 463 464&mmc1 { 465 vmmc-supply = <&vmmc>; 466 bus-width = <8>; 467}; 468 469&mmc2 { 470 status = "disabled"; 471}; 472 473&mmc3 { 474 status = "disabled"; 475}; 476 477&mmc4 { 478 status = "disabled"; 479}; 480 481&mmc5 { 482 pinctrl-names = "default"; 483 pinctrl-0 = <&wl12xx_pins>; 484 vmmc-supply = <&wl12xx_vmmc>; 485 interrupts-extended = <&wakeupgen GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH 486 &omap4_pmx_core 0x10e>; 487 non-removable; 488 bus-width = <4>; 489 cap-power-off-card; 490 491 #address-cells = <1>; 492 #size-cells = <0>; 493 wlcore: wlcore@2 { 494 compatible = "ti,wl1271"; 495 reg = <2>; 496 /* gpio_53 with gpmc_ncs3 pad as wakeup */ 497 interrupts-extended = <&gpio2 21 IRQ_TYPE_LEVEL_HIGH>, 498 <&omap4_pmx_core 0x3a>; 499 interrupt-names = "irq", "wakeup"; 500 ref-clock-frequency = <38400000>; 501 }; 502}; 503 504&emif1 { 505 cs1-used; 506 device-handle = <&elpida_ECB240ABACN>; 507}; 508 509&emif2 { 510 cs1-used; 511 device-handle = <&elpida_ECB240ABACN>; 512}; 513 514&mcbsp1 { 515 pinctrl-names = "default"; 516 pinctrl-0 = <&mcbsp1_pins>; 517 status = "okay"; 518}; 519 520&twl_usb_comparator { 521 usb-supply = <&vusb>; 522}; 523 524&uart2 { 525 interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH 526 &omap4_pmx_core OMAP4_UART2_RX>; 527}; 528 529&uart3 { 530 interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH 531 &omap4_pmx_core OMAP4_UART3_RX>; 532}; 533 534&uart4 { 535 interrupts-extended = <&wakeupgen GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH 536 &omap4_pmx_core OMAP4_UART4_RX>; 537}; 538 539&usb_otg_hs { 540 interface-type = <1>; 541 mode = <3>; 542 power = <50>; 543}; 544 545&usbhshost { 546 port1-mode = "ehci-phy"; 547}; 548 549&usbhsehci { 550 phys = <&hsusb1_phy>; 551 552 #address-cells = <1>; 553 #size-cells = <0>; 554 555 hub@1 { 556 compatible = "usb424,9514"; 557 reg = <1>; 558 #address-cells = <1>; 559 #size-cells = <0>; 560 561 ethernet: ethernet@1 { 562 compatible = "usb424,ec00"; 563 reg = <1>; 564 }; 565 }; 566}; 567 568&dss { 569 status = "okay"; 570 571 port { 572 dpi_out: endpoint { 573 remote-endpoint = <&tfp410_in>; 574 data-lines = <24>; 575 }; 576 }; 577}; 578 579&dsi2 { 580 status = "okay"; 581 vdd-supply = <&vcxio>; 582}; 583 584&hdmi { 585 status = "okay"; 586 vdda-supply = <&vdac>; 587 588 port { 589 hdmi_out: endpoint { 590 remote-endpoint = <&tpd12s015_in>; 591 }; 592 }; 593}; 594 595&dsp { 596 status = "okay"; 597 memory-region = <&dsp_memory_region>; 598 ti,timers = <&timer5>; 599 ti,watchdog-timers = <&timer6>; 600}; 601 602&ipu { 603 status = "okay"; 604 memory-region = <&ipu_memory_region>; 605 ti,timers = <&timer3>; 606 ti,watchdog-timers = <&timer9>, <&timer11>; 607}; 608