1 /*
2 * Copyright (c) 1997-1998 Mark Lord
3 * Copyright (c) 2007 MontaVista Software, Inc. <source@mvista.com>
4 *
5 * May be copied or modified under the terms of the GNU General Public License
6 *
7 * June 22, 2004 - get rid of check_region
8 * - Jesper Juhl
9 *
10 */
11
12 /*
13 * This module provides support for the bus-master IDE DMA function
14 * of the Tekram TRM290 chip, used on a variety of PCI IDE add-on boards,
15 * including a "Precision Instruments" board. The TRM290 pre-dates
16 * the sff-8038 standard (ide-dma.c) by a few months, and differs
17 * significantly enough to warrant separate routines for some functions,
18 * while re-using others from ide-dma.c.
19 *
20 * EXPERIMENTAL! It works for me (a sample of one).
21 *
22 * Works reliably for me in DMA mode (READs only),
23 * DMA WRITEs are disabled by default (see #define below);
24 *
25 * DMA is not enabled automatically for this chipset,
26 * but can be turned on manually (with "hdparm -d1") at run time.
27 *
28 * I need volunteers with "spare" drives for further testing
29 * and development, and maybe to help figure out the peculiarities.
30 * Even knowing the registers (below), some things behave strangely.
31 */
32
33 #define TRM290_NO_DMA_WRITES /* DMA writes seem unreliable sometimes */
34
35 /*
36 * TRM-290 PCI-IDE2 Bus Master Chip
37 * ================================
38 * The configuration registers are addressed in normal I/O port space
39 * and are used as follows:
40 *
41 * trm290_base depends on jumper settings, and is probed for by ide-dma.c
42 *
43 * trm290_base+2 when WRITTEN: chiptest register (byte, write-only)
44 * bit7 must always be written as "1"
45 * bits6-2 undefined
46 * bit1 1=legacy_compatible_mode, 0=native_pci_mode
47 * bit0 1=test_mode, 0=normal(default)
48 *
49 * trm290_base+2 when READ: status register (byte, read-only)
50 * bits7-2 undefined
51 * bit1 channel0 busmaster interrupt status 0=none, 1=asserted
52 * bit0 channel0 interrupt status 0=none, 1=asserted
53 *
54 * trm290_base+3 Interrupt mask register
55 * bits7-5 undefined
56 * bit4 legacy_header: 1=present, 0=absent
57 * bit3 channel1 busmaster interrupt status 0=none, 1=asserted (read only)
58 * bit2 channel1 interrupt status 0=none, 1=asserted (read only)
59 * bit1 channel1 interrupt mask: 1=masked, 0=unmasked(default)
60 * bit0 channel0 interrupt mask: 1=masked, 0=unmasked(default)
61 *
62 * trm290_base+1 "CPR" Config Pointer Register (byte)
63 * bit7 1=autoincrement CPR bits 2-0 after each access of CDR
64 * bit6 1=min. 1 wait-state posted write cycle (default), 0=0 wait-state
65 * bit5 0=enabled master burst access (default), 1=disable (write only)
66 * bit4 PCI DEVSEL# timing select: 1=medium(default), 0=fast
67 * bit3 0=primary IDE channel, 1=secondary IDE channel
68 * bits2-0 register index for accesses through CDR port
69 *
70 * trm290_base+0 "CDR" Config Data Register (word)
71 * two sets of seven config registers,
72 * selected by CPR bit 3 (channel) and CPR bits 2-0 (index 0 to 6),
73 * each index defined below:
74 *
75 * Index-0 Base address register for command block (word)
76 * defaults: 0x1f0 for primary, 0x170 for secondary
77 *
78 * Index-1 general config register (byte)
79 * bit7 1=DMA enable, 0=DMA disable
80 * bit6 1=activate IDE_RESET, 0=no action (default)
81 * bit5 1=enable IORDY, 0=disable IORDY (default)
82 * bit4 0=16-bit data port(default), 1=8-bit (XT) data port
83 * bit3 interrupt polarity: 1=active_low, 0=active_high(default)
84 * bit2 power-saving-mode(?): 1=enable, 0=disable(default) (write only)
85 * bit1 bus_master_mode(?): 1=enable, 0=disable(default)
86 * bit0 enable_io_ports: 1=enable(default), 0=disable
87 *
88 * Index-2 read-ahead counter preload bits 0-7 (byte, write only)
89 * bits7-0 bits7-0 of readahead count
90 *
91 * Index-3 read-ahead config register (byte, write only)
92 * bit7 1=enable_readahead, 0=disable_readahead(default)
93 * bit6 1=clear_FIFO, 0=no_action
94 * bit5 undefined
95 * bit4 mode4 timing control: 1=enable, 0=disable(default)
96 * bit3 undefined
97 * bit2 undefined
98 * bits1-0 bits9-8 of read-ahead count
99 *
100 * Index-4 base address register for control block (word)
101 * defaults: 0x3f6 for primary, 0x376 for secondary
102 *
103 * Index-5 data port timings (shared by both drives) (byte)
104 * standard PCI "clk" (clock) counts, default value = 0xf5
105 *
106 * bits7-6 setup time: 00=1clk, 01=2clk, 10=3clk, 11=4clk
107 * bits5-3 hold time: 000=1clk, 001=2clk, 010=3clk,
108 * 011=4clk, 100=5clk, 101=6clk,
109 * 110=8clk, 111=12clk
110 * bits2-0 active time: 000=2clk, 001=3clk, 010=4clk,
111 * 011=5clk, 100=6clk, 101=8clk,
112 * 110=12clk, 111=16clk
113 *
114 * Index-6 command/control port timings (shared by both drives) (byte)
115 * same layout as Index-5, default value = 0xde
116 *
117 * Suggested CDR programming for PIO mode0 (600ns):
118 * 0x01f0,0x21,0xff,0x80,0x03f6,0xf5,0xde ; primary
119 * 0x0170,0x21,0xff,0x80,0x0376,0xf5,0xde ; secondary
120 *
121 * Suggested CDR programming for PIO mode3 (180ns):
122 * 0x01f0,0x21,0xff,0x80,0x03f6,0x09,0xde ; primary
123 * 0x0170,0x21,0xff,0x80,0x0376,0x09,0xde ; secondary
124 *
125 * Suggested CDR programming for PIO mode4 (120ns):
126 * 0x01f0,0x21,0xff,0x80,0x03f6,0x00,0xde ; primary
127 * 0x0170,0x21,0xff,0x80,0x0376,0x00,0xde ; secondary
128 *
129 */
130
131 #include <linux/types.h>
132 #include <linux/module.h>
133 #include <linux/kernel.h>
134 #include <linux/ioport.h>
135 #include <linux/interrupt.h>
136 #include <linux/blkdev.h>
137 #include <linux/init.h>
138 #include <linux/pci.h>
139 #include <linux/ide.h>
140
141 #include <asm/io.h>
142
143 #define DRV_NAME "trm290"
144
trm290_prepare_drive(ide_drive_t * drive,unsigned int use_dma)145 static void trm290_prepare_drive (ide_drive_t *drive, unsigned int use_dma)
146 {
147 ide_hwif_t *hwif = drive->hwif;
148 u16 reg = 0;
149 unsigned long flags;
150
151 /* select PIO or DMA */
152 reg = use_dma ? (0x21 | 0x82) : (0x21 & ~0x82);
153
154 local_irq_save(flags);
155
156 if (reg != hwif->select_data) {
157 hwif->select_data = reg;
158 /* set PIO/DMA */
159 outb(0x51 | (hwif->channel << 3), hwif->config_data + 1);
160 outw(reg & 0xff, hwif->config_data);
161 }
162
163 /* enable IRQ if not probing */
164 if (drive->dev_flags & IDE_DFLAG_PRESENT) {
165 reg = inw(hwif->config_data + 3);
166 reg &= 0x13;
167 reg &= ~(1 << hwif->channel);
168 outw(reg, hwif->config_data + 3);
169 }
170
171 local_irq_restore(flags);
172 }
173
trm290_dev_select(ide_drive_t * drive)174 static void trm290_dev_select(ide_drive_t *drive)
175 {
176 trm290_prepare_drive(drive, !!(drive->dev_flags & IDE_DFLAG_USING_DMA));
177
178 outb(drive->select | ATA_DEVICE_OBS, drive->hwif->io_ports.device_addr);
179 }
180
trm290_dma_check(ide_drive_t * drive,struct ide_cmd * cmd)181 static int trm290_dma_check(ide_drive_t *drive, struct ide_cmd *cmd)
182 {
183 if (cmd->tf_flags & IDE_TFLAG_WRITE) {
184 #ifdef TRM290_NO_DMA_WRITES
185 /* always use PIO for writes */
186 return 1;
187 #endif
188 }
189 return 0;
190 }
191
trm290_dma_setup(ide_drive_t * drive,struct ide_cmd * cmd)192 static int trm290_dma_setup(ide_drive_t *drive, struct ide_cmd *cmd)
193 {
194 ide_hwif_t *hwif = drive->hwif;
195 unsigned int count, rw = (cmd->tf_flags & IDE_TFLAG_WRITE) ? 1 : 2;
196
197 count = ide_build_dmatable(drive, cmd);
198 if (count == 0)
199 /* try PIO instead of DMA */
200 return 1;
201
202 outl(hwif->dmatable_dma | rw, hwif->dma_base);
203 /* start DMA */
204 outw(count * 2 - 1, hwif->dma_base + 2);
205
206 return 0;
207 }
208
trm290_dma_start(ide_drive_t * drive)209 static void trm290_dma_start(ide_drive_t *drive)
210 {
211 trm290_prepare_drive(drive, 1);
212 }
213
trm290_dma_end(ide_drive_t * drive)214 static int trm290_dma_end(ide_drive_t *drive)
215 {
216 u16 status = inw(drive->hwif->dma_base + 2);
217
218 trm290_prepare_drive(drive, 0);
219
220 return status != 0x00ff;
221 }
222
trm290_dma_test_irq(ide_drive_t * drive)223 static int trm290_dma_test_irq(ide_drive_t *drive)
224 {
225 u16 status = inw(drive->hwif->dma_base + 2);
226
227 return status == 0x00ff;
228 }
229
trm290_dma_host_set(ide_drive_t * drive,int on)230 static void trm290_dma_host_set(ide_drive_t *drive, int on)
231 {
232 }
233
init_hwif_trm290(ide_hwif_t * hwif)234 static void __devinit init_hwif_trm290(ide_hwif_t *hwif)
235 {
236 struct pci_dev *dev = to_pci_dev(hwif->dev);
237 unsigned int cfg_base = pci_resource_start(dev, 4);
238 unsigned long flags;
239 u8 reg = 0;
240
241 if ((dev->class & 5) && cfg_base)
242 printk(KERN_INFO DRV_NAME " %s: chip", pci_name(dev));
243 else {
244 cfg_base = 0x3df0;
245 printk(KERN_INFO DRV_NAME " %s: using default", pci_name(dev));
246 }
247 printk(KERN_CONT " config base at 0x%04x\n", cfg_base);
248 hwif->config_data = cfg_base;
249 hwif->dma_base = (cfg_base + 4) ^ (hwif->channel ? 0x80 : 0);
250
251 printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n",
252 hwif->name, hwif->dma_base, hwif->dma_base + 3);
253
254 if (ide_allocate_dma_engine(hwif))
255 return;
256
257 local_irq_save(flags);
258 /* put config reg into first byte of hwif->select_data */
259 outb(0x51 | (hwif->channel << 3), hwif->config_data + 1);
260 /* select PIO as default */
261 hwif->select_data = 0x21;
262 outb(hwif->select_data, hwif->config_data);
263 /* get IRQ info */
264 reg = inb(hwif->config_data + 3);
265 /* mask IRQs for both ports */
266 reg = (reg & 0x10) | 0x03;
267 outb(reg, hwif->config_data + 3);
268 local_irq_restore(flags);
269
270 if (reg & 0x10)
271 /* legacy mode */
272 hwif->irq = hwif->channel ? 15 : 14;
273
274 #if 1
275 {
276 /*
277 * My trm290-based card doesn't seem to work with all possible values
278 * for the control basereg, so this kludge ensures that we use only
279 * values that are known to work. Ugh. -ml
280 */
281 u16 new, old, compat = hwif->channel ? 0x374 : 0x3f4;
282 static u16 next_offset = 0;
283 u8 old_mask;
284
285 outb(0x54 | (hwif->channel << 3), hwif->config_data + 1);
286 old = inw(hwif->config_data);
287 old &= ~1;
288 old_mask = inb(old + 2);
289 if (old != compat && old_mask == 0xff) {
290 /* leave lower 10 bits untouched */
291 compat += (next_offset += 0x400);
292 hwif->io_ports.ctl_addr = compat + 2;
293 outw(compat | 1, hwif->config_data);
294 new = inw(hwif->config_data);
295 printk(KERN_INFO "%s: control basereg workaround: "
296 "old=0x%04x, new=0x%04x\n",
297 hwif->name, old, new & ~1);
298 }
299 }
300 #endif
301 }
302
303 static const struct ide_tp_ops trm290_tp_ops = {
304 .exec_command = ide_exec_command,
305 .read_status = ide_read_status,
306 .read_altstatus = ide_read_altstatus,
307 .write_devctl = ide_write_devctl,
308
309 .dev_select = trm290_dev_select,
310 .tf_load = ide_tf_load,
311 .tf_read = ide_tf_read,
312
313 .input_data = ide_input_data,
314 .output_data = ide_output_data,
315 };
316
317 static struct ide_dma_ops trm290_dma_ops = {
318 .dma_host_set = trm290_dma_host_set,
319 .dma_setup = trm290_dma_setup,
320 .dma_start = trm290_dma_start,
321 .dma_end = trm290_dma_end,
322 .dma_test_irq = trm290_dma_test_irq,
323 .dma_lost_irq = ide_dma_lost_irq,
324 .dma_check = trm290_dma_check,
325 };
326
327 static const struct ide_port_info trm290_chipset __devinitdata = {
328 .name = DRV_NAME,
329 .init_hwif = init_hwif_trm290,
330 .tp_ops = &trm290_tp_ops,
331 .dma_ops = &trm290_dma_ops,
332 .host_flags = IDE_HFLAG_TRM290 |
333 IDE_HFLAG_NO_ATAPI_DMA |
334 #if 0 /* play it safe for now */
335 IDE_HFLAG_TRUST_BIOS_FOR_DMA |
336 #endif
337 IDE_HFLAG_NO_AUTODMA |
338 IDE_HFLAG_NO_LBA48,
339 };
340
trm290_init_one(struct pci_dev * dev,const struct pci_device_id * id)341 static int __devinit trm290_init_one(struct pci_dev *dev, const struct pci_device_id *id)
342 {
343 return ide_pci_init_one(dev, &trm290_chipset, NULL);
344 }
345
346 static const struct pci_device_id trm290_pci_tbl[] = {
347 { PCI_VDEVICE(TEKRAM, PCI_DEVICE_ID_TEKRAM_DC290), 0 },
348 { 0, },
349 };
350 MODULE_DEVICE_TABLE(pci, trm290_pci_tbl);
351
352 static struct pci_driver trm290_pci_driver = {
353 .name = "TRM290_IDE",
354 .id_table = trm290_pci_tbl,
355 .probe = trm290_init_one,
356 .remove = ide_pci_remove,
357 };
358
trm290_ide_init(void)359 static int __init trm290_ide_init(void)
360 {
361 return ide_pci_register_driver(&trm290_pci_driver);
362 }
363
trm290_ide_exit(void)364 static void __exit trm290_ide_exit(void)
365 {
366 pci_unregister_driver(&trm290_pci_driver);
367 }
368
369 module_init(trm290_ide_init);
370 module_exit(trm290_ide_exit);
371
372 MODULE_AUTHOR("Mark Lord");
373 MODULE_DESCRIPTION("PCI driver module for Tekram TRM290 IDE");
374 MODULE_LICENSE("GPL");
375