1(C)Copyright 1998-2000 SysKonnect,
2===========================================================================
3
4skfp.txt created 11-May-2000
5
6Readme File for skfp.o v2.06
7
8
9This file contains
10(1) OVERVIEW
11(2) SUPPORTED ADAPTERS
12(3) GENERAL INFORMATION
13(4) INSTALLATION
14(5) INCLUSION OF THE ADAPTER IN SYSTEM START
15(6) TROUBLESHOOTING
16(7) FUNCTION OF THE ADAPTER LEDS
17(8) HISTORY
18
19===========================================================================
20
21
22
23(1) OVERVIEW
24============
25
26This README explains how to use the driver 'skfp' for Linux with your
27network adapter.
28
29Chapter 2: Contains a list of all network adapters that are supported by
30	   this driver.
31
32Chapter 3: Gives some general information.
33
34Chapter 4: Describes common problems and solutions.
35
36Chapter 5: Shows the changed functionality of the adapter LEDs.
37
38Chapter 6: History of development.
39
40***
41
42
43(2) SUPPORTED ADAPTERS
44======================
45
46The network driver 'skfp' supports the following network adapters:
47SysKonnect adapters:
48  - SK-5521 (SK-NET FDDI-UP)
49  - SK-5522 (SK-NET FDDI-UP DAS)
50  - SK-5541 (SK-NET FDDI-FP)
51  - SK-5543 (SK-NET FDDI-LP)
52  - SK-5544 (SK-NET FDDI-LP DAS)
53  - SK-5821 (SK-NET FDDI-UP64)
54  - SK-5822 (SK-NET FDDI-UP64 DAS)
55  - SK-5841 (SK-NET FDDI-FP64)
56  - SK-5843 (SK-NET FDDI-LP64)
57  - SK-5844 (SK-NET FDDI-LP64 DAS)
58Compaq adapters (not tested):
59  - Netelligent 100 FDDI DAS Fibre SC
60  - Netelligent 100 FDDI SAS Fibre SC
61  - Netelligent 100 FDDI DAS UTP
62  - Netelligent 100 FDDI SAS UTP
63  - Netelligent 100 FDDI SAS Fibre MIC
64***
65
66
67(3) GENERAL INFORMATION
68=======================
69
70From v2.01 on, the driver is integrated in the linux kernel sources.
71Therefore, the installation is the same as for any other adapter
72supported by the kernel.
73Refer to the manual of your distribution about the installation
74of network adapters.
75Makes my life much easier :-)
76***
77
78
79(4) TROUBLESHOOTING
80===================
81
82If you run into problems during installation, check those items:
83
84Problem:  The FDDI adapter cannot be found by the driver.
85Reason:   Look in /proc/pci for the following entry:
86             'FDDI network controller: SysKonnect SK-FDDI-PCI ...'
87	  If this entry exists, then the FDDI adapter has been
88	  found by the system and should be able to be used.
89	  If this entry does not exist or if the file '/proc/pci'
90	  is not there, then you may have a hardware problem or PCI
91	  support may not be enabled in your kernel.
92	  The adapter can be checked using the diagnostic program
93	  which is available from the SysKonnect web site:
94	      www.syskonnect.de
95	  Some COMPAQ machines have a problem with PCI under
96	  Linux. This is described in the 'PCI howto' document
97	  (included in some distributions or available from the
98	  www, e.g. at 'www.linux.org') and no workaround is available.
99
100Problem:  You want to use your computer as a router between
101          multiple IP subnetworks (using multiple adapters), but
102	  you cannot reach computers in other subnetworks.
103Reason:   Either the router's kernel is not configured for IP
104	  forwarding or there is a problem with the routing table
105	  and gateway configuration in at least one of the
106	  computers.
107
108If your problem is not listed here, please contact our
109technical support for help.
110You can send email to:
111  linux@syskonnect.de
112When contacting our technical support,
113please ensure that the following information is available:
114- System Manufacturer and Model
115- Boards in your system
116- Distribution
117- Kernel version
118
119***
120
121
122(5) FUNCTION OF THE ADAPTER LEDS
123================================
124
125        The functionality of the LED's on the FDDI network adapters was
126        changed in SMT version v2.82. With this new SMT version, the yellow
127        LED works as a ring operational indicator. An active yellow LED
128        indicates that the ring is down. The green LED on the adapter now
129        works as a link indicator where an active GREEN LED indicates that
130        the respective port has a physical connection.
131
132        With versions of SMT prior to v2.82 a ring up was indicated if the
133        yellow LED was off while the green LED(s) showed the connection
134        status of the adapter. During a ring down the green LED was off and
135        the yellow LED was on.
136
137        All implementations indicate that a driver is not loaded if
138        all LEDs are off.
139
140***
141
142
143(6) HISTORY
144===========
145
146v2.06 (20000511) (In-Kernel version)
147    New features:
148	- 64 bit support
149	- new pci dma interface
150	- in kernel 2.3.99
151
152v2.05 (20000217) (In-Kernel version)
153    New features:
154	- Changes for 2.3.45 kernel
155
156v2.04 (20000207) (Standalone version)
157    New features:
158	- Added rx/tx byte counter
159
160v2.03 (20000111) (Standalone version)
161    Problems fixed:
162	- Fixed printk statements from v2.02
163
164v2.02 (991215) (Standalone version)
165    Problems fixed:
166	- Removed unnecessary output
167	- Fixed path for "printver.sh" in makefile
168
169v2.01 (991122) (In-Kernel version)
170    New features:
171	- Integration in Linux kernel sources
172	- Support for memory mapped I/O.
173
174v2.00 (991112)
175    New features:
176	- Full source released under GPL
177
178v1.05 (991023)
179    Problems fixed:
180	- Compilation with kernel version 2.2.13 failed
181
182v1.04 (990427)
183    Changes:
184	- New SMT module included, changing LED functionality
185    Problems fixed:
186	- Synchronization on SMP machines was buggy
187
188v1.03 (990325)
189    Problems fixed:
190	- Interrupt routing on SMP machines could be incorrect
191
192v1.02 (990310)
193    New features:
194	- Support for kernel versions 2.2.x added
195	- Kernel patch instead of private duplicate of kernel functions
196
197v1.01 (980812)
198    Problems fixed:
199	Connection hangup with telnet
200	Slow telnet connection
201
202v1.00 beta 01 (980507)
203    New features:
204	None.
205    Problems fixed:
206	None.
207    Known limitations:
208        - tar archive instead of standard package format (rpm).
209	- FDDI statistic is empty.
210	- not tested with 2.1.xx kernels
211	- integration in kernel not tested
212	- not tested simultaneously with FDDI adapters from other vendors.
213	- only X86 processors supported.
214	- SBA (Synchronous Bandwidth Allocator) parameters can
215	  not be configured.
216	- does not work on some COMPAQ machines. See the PCI howto
217	  document for details about this problem.
218	- data corruption with kernel versions below 2.0.33.
219
220*** End of information file ***
221