1 /*
2 * OHCI HCD (Host Controller Driver) for USB.
3 *
4 * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
5 * (C) Copyright 2000-2004 David Brownell <dbrownell@users.sourceforge.net>
6 *
7 * [ Initialisation is based on Linus' ]
8 * [ uhci code and gregs ohci fragments ]
9 * [ (C) Copyright 1999 Linus Torvalds ]
10 * [ (C) Copyright 1999 Gregory P. Smith]
11 *
12 *
13 * OHCI is the main "non-Intel/VIA" standard for USB 1.1 host controller
14 * interfaces (though some non-x86 Intel chips use it). It supports
15 * smarter hardware than UHCI. A download link for the spec available
16 * through the http://www.usb.org website.
17 *
18 * This file is licenced under the GPL.
19 */
20
21 #include <linux/module.h>
22 #include <linux/moduleparam.h>
23 #include <linux/pci.h>
24 #include <linux/kernel.h>
25 #include <linux/delay.h>
26 #include <linux/ioport.h>
27 #include <linux/sched.h>
28 #include <linux/slab.h>
29 #include <linux/errno.h>
30 #include <linux/init.h>
31 #include <linux/timer.h>
32 #include <linux/list.h>
33 #include <linux/usb.h>
34 #include <linux/usb/otg.h>
35 #include <linux/usb/hcd.h>
36 #include <linux/dma-mapping.h>
37 #include <linux/dmapool.h>
38 #include <linux/workqueue.h>
39 #include <linux/debugfs.h>
40
41 #include <asm/io.h>
42 #include <asm/irq.h>
43 #include <asm/system.h>
44 #include <asm/unaligned.h>
45 #include <asm/byteorder.h>
46
47
48 #define DRIVER_AUTHOR "Roman Weissgaerber, David Brownell"
49 #define DRIVER_DESC "USB 1.1 'Open' Host Controller (OHCI) Driver"
50
51 /*-------------------------------------------------------------------------*/
52
53 #undef OHCI_VERBOSE_DEBUG /* not always helpful */
54
55 /* For initializing controller (mask in an HCFS mode too) */
56 #define OHCI_CONTROL_INIT OHCI_CTRL_CBSR
57 #define OHCI_INTR_INIT \
58 (OHCI_INTR_MIE | OHCI_INTR_RHSC | OHCI_INTR_UE \
59 | OHCI_INTR_RD | OHCI_INTR_WDH)
60
61 #ifdef __hppa__
62 /* On PA-RISC, PDC can leave IR set incorrectly; ignore it there. */
63 #define IR_DISABLE
64 #endif
65
66 #ifdef CONFIG_ARCH_OMAP
67 /* OMAP doesn't support IR (no SMM; not needed) */
68 #define IR_DISABLE
69 #endif
70
71 /*-------------------------------------------------------------------------*/
72
73 static const char hcd_name [] = "ohci_hcd";
74
75 #define STATECHANGE_DELAY msecs_to_jiffies(300)
76
77 #include "ohci.h"
78 #include "pci-quirks.h"
79
80 static void ohci_dump (struct ohci_hcd *ohci, int verbose);
81 static int ohci_init (struct ohci_hcd *ohci);
82 static void ohci_stop (struct usb_hcd *hcd);
83
84 #if defined(CONFIG_PM) || defined(CONFIG_PCI)
85 static int ohci_restart (struct ohci_hcd *ohci);
86 #endif
87
88 #ifdef CONFIG_PCI
89 static void sb800_prefetch(struct ohci_hcd *ohci, int on);
90 #else
sb800_prefetch(struct ohci_hcd * ohci,int on)91 static inline void sb800_prefetch(struct ohci_hcd *ohci, int on)
92 {
93 return;
94 }
95 #endif
96
97
98 #include "ohci-hub.c"
99 #include "ohci-dbg.c"
100 #include "ohci-mem.c"
101 #include "ohci-q.c"
102
103
104 /*
105 * On architectures with edge-triggered interrupts we must never return
106 * IRQ_NONE.
107 */
108 #if defined(CONFIG_SA1111) /* ... or other edge-triggered systems */
109 #define IRQ_NOTMINE IRQ_HANDLED
110 #else
111 #define IRQ_NOTMINE IRQ_NONE
112 #endif
113
114
115 /* Some boards misreport power switching/overcurrent */
116 static int distrust_firmware = 1;
117 module_param (distrust_firmware, bool, 0);
118 MODULE_PARM_DESC (distrust_firmware,
119 "true to distrust firmware power/overcurrent setup");
120
121 /* Some boards leave IR set wrongly, since they fail BIOS/SMM handshakes */
122 static int no_handshake = 0;
123 module_param (no_handshake, bool, 0);
124 MODULE_PARM_DESC (no_handshake, "true (not default) disables BIOS handshake");
125
126 /*-------------------------------------------------------------------------*/
127
128 /*
129 * queue up an urb for anything except the root hub
130 */
ohci_urb_enqueue(struct usb_hcd * hcd,struct urb * urb,gfp_t mem_flags)131 static int ohci_urb_enqueue (
132 struct usb_hcd *hcd,
133 struct urb *urb,
134 gfp_t mem_flags
135 ) {
136 struct ohci_hcd *ohci = hcd_to_ohci (hcd);
137 struct ed *ed;
138 urb_priv_t *urb_priv;
139 unsigned int pipe = urb->pipe;
140 int i, size = 0;
141 unsigned long flags;
142 int retval = 0;
143
144 #ifdef OHCI_VERBOSE_DEBUG
145 urb_print(urb, "SUB", usb_pipein(pipe), -EINPROGRESS);
146 #endif
147
148 /* every endpoint has a ed, locate and maybe (re)initialize it */
149 if (! (ed = ed_get (ohci, urb->ep, urb->dev, pipe, urb->interval)))
150 return -ENOMEM;
151
152 /* for the private part of the URB we need the number of TDs (size) */
153 switch (ed->type) {
154 case PIPE_CONTROL:
155 /* td_submit_urb() doesn't yet handle these */
156 if (urb->transfer_buffer_length > 4096)
157 return -EMSGSIZE;
158
159 /* 1 TD for setup, 1 for ACK, plus ... */
160 size = 2;
161 /* FALLTHROUGH */
162 // case PIPE_INTERRUPT:
163 // case PIPE_BULK:
164 default:
165 /* one TD for every 4096 Bytes (can be up to 8K) */
166 size += urb->transfer_buffer_length / 4096;
167 /* ... and for any remaining bytes ... */
168 if ((urb->transfer_buffer_length % 4096) != 0)
169 size++;
170 /* ... and maybe a zero length packet to wrap it up */
171 if (size == 0)
172 size++;
173 else if ((urb->transfer_flags & URB_ZERO_PACKET) != 0
174 && (urb->transfer_buffer_length
175 % usb_maxpacket (urb->dev, pipe,
176 usb_pipeout (pipe))) == 0)
177 size++;
178 break;
179 case PIPE_ISOCHRONOUS: /* number of packets from URB */
180 size = urb->number_of_packets;
181 break;
182 }
183
184 /* allocate the private part of the URB */
185 urb_priv = kzalloc (sizeof (urb_priv_t) + size * sizeof (struct td *),
186 mem_flags);
187 if (!urb_priv)
188 return -ENOMEM;
189 INIT_LIST_HEAD (&urb_priv->pending);
190 urb_priv->length = size;
191 urb_priv->ed = ed;
192
193 /* allocate the TDs (deferring hash chain updates) */
194 for (i = 0; i < size; i++) {
195 urb_priv->td [i] = td_alloc (ohci, mem_flags);
196 if (!urb_priv->td [i]) {
197 urb_priv->length = i;
198 urb_free_priv (ohci, urb_priv);
199 return -ENOMEM;
200 }
201 }
202
203 spin_lock_irqsave (&ohci->lock, flags);
204
205 /* don't submit to a dead HC */
206 if (!HCD_HW_ACCESSIBLE(hcd)) {
207 retval = -ENODEV;
208 goto fail;
209 }
210 if (!HC_IS_RUNNING(hcd->state)) {
211 retval = -ENODEV;
212 goto fail;
213 }
214 retval = usb_hcd_link_urb_to_ep(hcd, urb);
215 if (retval)
216 goto fail;
217
218 /* schedule the ed if needed */
219 if (ed->state == ED_IDLE) {
220 retval = ed_schedule (ohci, ed);
221 if (retval < 0) {
222 usb_hcd_unlink_urb_from_ep(hcd, urb);
223 goto fail;
224 }
225 if (ed->type == PIPE_ISOCHRONOUS) {
226 u16 frame = ohci_frame_no(ohci);
227
228 /* delay a few frames before the first TD */
229 frame += max_t (u16, 8, ed->interval);
230 frame &= ~(ed->interval - 1);
231 frame |= ed->branch;
232 urb->start_frame = frame;
233
234 /* yes, only URB_ISO_ASAP is supported, and
235 * urb->start_frame is never used as input.
236 */
237 }
238 } else if (ed->type == PIPE_ISOCHRONOUS)
239 urb->start_frame = ed->last_iso + ed->interval;
240
241 /* fill the TDs and link them to the ed; and
242 * enable that part of the schedule, if needed
243 * and update count of queued periodic urbs
244 */
245 urb->hcpriv = urb_priv;
246 td_submit_urb (ohci, urb);
247
248 fail:
249 if (retval)
250 urb_free_priv (ohci, urb_priv);
251 spin_unlock_irqrestore (&ohci->lock, flags);
252 return retval;
253 }
254
255 /*
256 * decouple the URB from the HC queues (TDs, urb_priv).
257 * reporting is always done
258 * asynchronously, and we might be dealing with an urb that's
259 * partially transferred, or an ED with other urbs being unlinked.
260 */
ohci_urb_dequeue(struct usb_hcd * hcd,struct urb * urb,int status)261 static int ohci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
262 {
263 struct ohci_hcd *ohci = hcd_to_ohci (hcd);
264 unsigned long flags;
265 int rc;
266
267 #ifdef OHCI_VERBOSE_DEBUG
268 urb_print(urb, "UNLINK", 1, status);
269 #endif
270
271 spin_lock_irqsave (&ohci->lock, flags);
272 rc = usb_hcd_check_unlink_urb(hcd, urb, status);
273 if (rc) {
274 ; /* Do nothing */
275 } else if (HC_IS_RUNNING(hcd->state)) {
276 urb_priv_t *urb_priv;
277
278 /* Unless an IRQ completed the unlink while it was being
279 * handed to us, flag it for unlink and giveback, and force
280 * some upcoming INTR_SF to call finish_unlinks()
281 */
282 urb_priv = urb->hcpriv;
283 if (urb_priv) {
284 if (urb_priv->ed->state == ED_OPER)
285 start_ed_unlink (ohci, urb_priv->ed);
286 }
287 } else {
288 /*
289 * with HC dead, we won't respect hc queue pointers
290 * any more ... just clean up every urb's memory.
291 */
292 if (urb->hcpriv)
293 finish_urb(ohci, urb, status);
294 }
295 spin_unlock_irqrestore (&ohci->lock, flags);
296 return rc;
297 }
298
299 /*-------------------------------------------------------------------------*/
300
301 /* frees config/altsetting state for endpoints,
302 * including ED memory, dummy TD, and bulk/intr data toggle
303 */
304
305 static void
ohci_endpoint_disable(struct usb_hcd * hcd,struct usb_host_endpoint * ep)306 ohci_endpoint_disable (struct usb_hcd *hcd, struct usb_host_endpoint *ep)
307 {
308 struct ohci_hcd *ohci = hcd_to_ohci (hcd);
309 unsigned long flags;
310 struct ed *ed = ep->hcpriv;
311 unsigned limit = 1000;
312
313 /* ASSERT: any requests/urbs are being unlinked */
314 /* ASSERT: nobody can be submitting urbs for this any more */
315
316 if (!ed)
317 return;
318
319 rescan:
320 spin_lock_irqsave (&ohci->lock, flags);
321
322 if (!HC_IS_RUNNING (hcd->state)) {
323 sanitize:
324 ed->state = ED_IDLE;
325 if (quirk_zfmicro(ohci) && ed->type == PIPE_INTERRUPT)
326 ohci->eds_scheduled--;
327 finish_unlinks (ohci, 0);
328 }
329
330 switch (ed->state) {
331 case ED_UNLINK: /* wait for hw to finish? */
332 /* major IRQ delivery trouble loses INTR_SF too... */
333 if (limit-- == 0) {
334 ohci_warn(ohci, "ED unlink timeout\n");
335 if (quirk_zfmicro(ohci)) {
336 ohci_warn(ohci, "Attempting ZF TD recovery\n");
337 ohci->ed_to_check = ed;
338 ohci->zf_delay = 2;
339 }
340 goto sanitize;
341 }
342 spin_unlock_irqrestore (&ohci->lock, flags);
343 schedule_timeout_uninterruptible(1);
344 goto rescan;
345 case ED_IDLE: /* fully unlinked */
346 if (list_empty (&ed->td_list)) {
347 td_free (ohci, ed->dummy);
348 ed_free (ohci, ed);
349 break;
350 }
351 /* else FALL THROUGH */
352 default:
353 /* caller was supposed to have unlinked any requests;
354 * that's not our job. can't recover; must leak ed.
355 */
356 ohci_err (ohci, "leak ed %p (#%02x) state %d%s\n",
357 ed, ep->desc.bEndpointAddress, ed->state,
358 list_empty (&ed->td_list) ? "" : " (has tds)");
359 td_free (ohci, ed->dummy);
360 break;
361 }
362 ep->hcpriv = NULL;
363 spin_unlock_irqrestore (&ohci->lock, flags);
364 }
365
ohci_get_frame(struct usb_hcd * hcd)366 static int ohci_get_frame (struct usb_hcd *hcd)
367 {
368 struct ohci_hcd *ohci = hcd_to_ohci (hcd);
369
370 return ohci_frame_no(ohci);
371 }
372
ohci_usb_reset(struct ohci_hcd * ohci)373 static void ohci_usb_reset (struct ohci_hcd *ohci)
374 {
375 ohci->hc_control = ohci_readl (ohci, &ohci->regs->control);
376 ohci->hc_control &= OHCI_CTRL_RWC;
377 ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
378 }
379
380 /* ohci_shutdown forcibly disables IRQs and DMA, helping kexec and
381 * other cases where the next software may expect clean state from the
382 * "firmware". this is bus-neutral, unlike shutdown() methods.
383 */
384 static void
ohci_shutdown(struct usb_hcd * hcd)385 ohci_shutdown (struct usb_hcd *hcd)
386 {
387 struct ohci_hcd *ohci;
388
389 ohci = hcd_to_ohci (hcd);
390 ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
391 ohci->hc_control = ohci_readl(ohci, &ohci->regs->control);
392
393 /* If the SHUTDOWN quirk is set, don't put the controller in RESET */
394 ohci->hc_control &= (ohci->flags & OHCI_QUIRK_SHUTDOWN ?
395 OHCI_CTRL_RWC | OHCI_CTRL_HCFS :
396 OHCI_CTRL_RWC);
397 ohci_writel(ohci, ohci->hc_control, &ohci->regs->control);
398
399 /* flush the writes */
400 (void) ohci_readl (ohci, &ohci->regs->control);
401 }
402
check_ed(struct ohci_hcd * ohci,struct ed * ed)403 static int check_ed(struct ohci_hcd *ohci, struct ed *ed)
404 {
405 return (hc32_to_cpu(ohci, ed->hwINFO) & ED_IN) != 0
406 && (hc32_to_cpu(ohci, ed->hwHeadP) & TD_MASK)
407 == (hc32_to_cpu(ohci, ed->hwTailP) & TD_MASK)
408 && !list_empty(&ed->td_list);
409 }
410
411 /* ZF Micro watchdog timer callback. The ZF Micro chipset sometimes completes
412 * an interrupt TD but neglects to add it to the donelist. On systems with
413 * this chipset, we need to periodically check the state of the queues to look
414 * for such "lost" TDs.
415 */
unlink_watchdog_func(unsigned long _ohci)416 static void unlink_watchdog_func(unsigned long _ohci)
417 {
418 unsigned long flags;
419 unsigned max;
420 unsigned seen_count = 0;
421 unsigned i;
422 struct ed **seen = NULL;
423 struct ohci_hcd *ohci = (struct ohci_hcd *) _ohci;
424
425 spin_lock_irqsave(&ohci->lock, flags);
426 max = ohci->eds_scheduled;
427 if (!max)
428 goto done;
429
430 if (ohci->ed_to_check)
431 goto out;
432
433 seen = kcalloc(max, sizeof *seen, GFP_ATOMIC);
434 if (!seen)
435 goto out;
436
437 for (i = 0; i < NUM_INTS; i++) {
438 struct ed *ed = ohci->periodic[i];
439
440 while (ed) {
441 unsigned temp;
442
443 /* scan this branch of the periodic schedule tree */
444 for (temp = 0; temp < seen_count; temp++) {
445 if (seen[temp] == ed) {
446 /* we've checked it and what's after */
447 ed = NULL;
448 break;
449 }
450 }
451 if (!ed)
452 break;
453 seen[seen_count++] = ed;
454 if (!check_ed(ohci, ed)) {
455 ed = ed->ed_next;
456 continue;
457 }
458
459 /* HC's TD list is empty, but HCD sees at least one
460 * TD that's not been sent through the donelist.
461 */
462 ohci->ed_to_check = ed;
463 ohci->zf_delay = 2;
464
465 /* The HC may wait until the next frame to report the
466 * TD as done through the donelist and INTR_WDH. (We
467 * just *assume* it's not a multi-TD interrupt URB;
468 * those could defer the IRQ more than one frame, using
469 * DI...) Check again after the next INTR_SF.
470 */
471 ohci_writel(ohci, OHCI_INTR_SF,
472 &ohci->regs->intrstatus);
473 ohci_writel(ohci, OHCI_INTR_SF,
474 &ohci->regs->intrenable);
475
476 /* flush those writes */
477 (void) ohci_readl(ohci, &ohci->regs->control);
478
479 goto out;
480 }
481 }
482 out:
483 kfree(seen);
484 if (ohci->eds_scheduled)
485 mod_timer(&ohci->unlink_watchdog, round_jiffies(jiffies + HZ));
486 done:
487 spin_unlock_irqrestore(&ohci->lock, flags);
488 }
489
490 /*-------------------------------------------------------------------------*
491 * HC functions
492 *-------------------------------------------------------------------------*/
493
494 /* init memory, and kick BIOS/SMM off */
495
ohci_init(struct ohci_hcd * ohci)496 static int ohci_init (struct ohci_hcd *ohci)
497 {
498 int ret;
499 struct usb_hcd *hcd = ohci_to_hcd(ohci);
500
501 if (distrust_firmware)
502 ohci->flags |= OHCI_QUIRK_HUB_POWER;
503
504 disable (ohci);
505 ohci->regs = hcd->regs;
506
507 /* REVISIT this BIOS handshake is now moved into PCI "quirks", and
508 * was never needed for most non-PCI systems ... remove the code?
509 */
510
511 #ifndef IR_DISABLE
512 /* SMM owns the HC? not for long! */
513 if (!no_handshake && ohci_readl (ohci,
514 &ohci->regs->control) & OHCI_CTRL_IR) {
515 u32 temp;
516
517 ohci_dbg (ohci, "USB HC TakeOver from BIOS/SMM\n");
518
519 /* this timeout is arbitrary. we make it long, so systems
520 * depending on usb keyboards may be usable even if the
521 * BIOS/SMM code seems pretty broken.
522 */
523 temp = 500; /* arbitrary: five seconds */
524
525 ohci_writel (ohci, OHCI_INTR_OC, &ohci->regs->intrenable);
526 ohci_writel (ohci, OHCI_OCR, &ohci->regs->cmdstatus);
527 while (ohci_readl (ohci, &ohci->regs->control) & OHCI_CTRL_IR) {
528 msleep (10);
529 if (--temp == 0) {
530 ohci_err (ohci, "USB HC takeover failed!"
531 " (BIOS/SMM bug)\n");
532 return -EBUSY;
533 }
534 }
535 ohci_usb_reset (ohci);
536 }
537 #endif
538
539 /* Disable HC interrupts */
540 ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
541
542 /* flush the writes, and save key bits like RWC */
543 if (ohci_readl (ohci, &ohci->regs->control) & OHCI_CTRL_RWC)
544 ohci->hc_control |= OHCI_CTRL_RWC;
545
546 /* Read the number of ports unless overridden */
547 if (ohci->num_ports == 0)
548 ohci->num_ports = roothub_a(ohci) & RH_A_NDP;
549
550 if (ohci->hcca)
551 return 0;
552
553 ohci->hcca = dma_alloc_coherent (hcd->self.controller,
554 sizeof *ohci->hcca, &ohci->hcca_dma, 0);
555 if (!ohci->hcca)
556 return -ENOMEM;
557
558 if ((ret = ohci_mem_init (ohci)) < 0)
559 ohci_stop (hcd);
560 else {
561 create_debug_files (ohci);
562 }
563
564 return ret;
565 }
566
567 /*-------------------------------------------------------------------------*/
568
569 /* Start an OHCI controller, set the BUS operational
570 * resets USB and controller
571 * enable interrupts
572 */
ohci_run(struct ohci_hcd * ohci)573 static int ohci_run (struct ohci_hcd *ohci)
574 {
575 u32 mask, val;
576 int first = ohci->fminterval == 0;
577 struct usb_hcd *hcd = ohci_to_hcd(ohci);
578
579 disable (ohci);
580
581 /* boot firmware should have set this up (5.1.1.3.1) */
582 if (first) {
583
584 val = ohci_readl (ohci, &ohci->regs->fminterval);
585 ohci->fminterval = val & 0x3fff;
586 if (ohci->fminterval != FI)
587 ohci_dbg (ohci, "fminterval delta %d\n",
588 ohci->fminterval - FI);
589 ohci->fminterval |= FSMP (ohci->fminterval) << 16;
590 /* also: power/overcurrent flags in roothub.a */
591 }
592
593 /* Reset USB nearly "by the book". RemoteWakeupConnected has
594 * to be checked in case boot firmware (BIOS/SMM/...) has set up
595 * wakeup in a way the bus isn't aware of (e.g., legacy PCI PM).
596 * If the bus glue detected wakeup capability then it should
597 * already be enabled; if so we'll just enable it again.
598 */
599 if ((ohci->hc_control & OHCI_CTRL_RWC) != 0)
600 device_set_wakeup_capable(hcd->self.controller, 1);
601
602 switch (ohci->hc_control & OHCI_CTRL_HCFS) {
603 case OHCI_USB_OPER:
604 val = 0;
605 break;
606 case OHCI_USB_SUSPEND:
607 case OHCI_USB_RESUME:
608 ohci->hc_control &= OHCI_CTRL_RWC;
609 ohci->hc_control |= OHCI_USB_RESUME;
610 val = 10 /* msec wait */;
611 break;
612 // case OHCI_USB_RESET:
613 default:
614 ohci->hc_control &= OHCI_CTRL_RWC;
615 ohci->hc_control |= OHCI_USB_RESET;
616 val = 50 /* msec wait */;
617 break;
618 }
619 ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
620 // flush the writes
621 (void) ohci_readl (ohci, &ohci->regs->control);
622 msleep(val);
623
624 memset (ohci->hcca, 0, sizeof (struct ohci_hcca));
625
626 /* 2msec timelimit here means no irqs/preempt */
627 spin_lock_irq (&ohci->lock);
628
629 retry:
630 /* HC Reset requires max 10 us delay */
631 ohci_writel (ohci, OHCI_HCR, &ohci->regs->cmdstatus);
632 val = 30; /* ... allow extra time */
633 while ((ohci_readl (ohci, &ohci->regs->cmdstatus) & OHCI_HCR) != 0) {
634 if (--val == 0) {
635 spin_unlock_irq (&ohci->lock);
636 ohci_err (ohci, "USB HC reset timed out!\n");
637 return -1;
638 }
639 udelay (1);
640 }
641
642 /* now we're in the SUSPEND state ... must go OPERATIONAL
643 * within 2msec else HC enters RESUME
644 *
645 * ... but some hardware won't init fmInterval "by the book"
646 * (SiS, OPTi ...), so reset again instead. SiS doesn't need
647 * this if we write fmInterval after we're OPERATIONAL.
648 * Unclear about ALi, ServerWorks, and others ... this could
649 * easily be a longstanding bug in chip init on Linux.
650 */
651 if (ohci->flags & OHCI_QUIRK_INITRESET) {
652 ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
653 // flush those writes
654 (void) ohci_readl (ohci, &ohci->regs->control);
655 }
656
657 /* Tell the controller where the control and bulk lists are
658 * The lists are empty now. */
659 ohci_writel (ohci, 0, &ohci->regs->ed_controlhead);
660 ohci_writel (ohci, 0, &ohci->regs->ed_bulkhead);
661
662 /* a reset clears this */
663 ohci_writel (ohci, (u32) ohci->hcca_dma, &ohci->regs->hcca);
664
665 periodic_reinit (ohci);
666
667 /* some OHCI implementations are finicky about how they init.
668 * bogus values here mean not even enumeration could work.
669 */
670 if ((ohci_readl (ohci, &ohci->regs->fminterval) & 0x3fff0000) == 0
671 || !ohci_readl (ohci, &ohci->regs->periodicstart)) {
672 if (!(ohci->flags & OHCI_QUIRK_INITRESET)) {
673 ohci->flags |= OHCI_QUIRK_INITRESET;
674 ohci_dbg (ohci, "enabling initreset quirk\n");
675 goto retry;
676 }
677 spin_unlock_irq (&ohci->lock);
678 ohci_err (ohci, "init err (%08x %04x)\n",
679 ohci_readl (ohci, &ohci->regs->fminterval),
680 ohci_readl (ohci, &ohci->regs->periodicstart));
681 return -EOVERFLOW;
682 }
683
684 /* use rhsc irqs after khubd is fully initialized */
685 set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
686 hcd->uses_new_polling = 1;
687
688 /* start controller operations */
689 ohci->hc_control &= OHCI_CTRL_RWC;
690 ohci->hc_control |= OHCI_CONTROL_INIT | OHCI_USB_OPER;
691 ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
692 hcd->state = HC_STATE_RUNNING;
693
694 /* wake on ConnectStatusChange, matching external hubs */
695 ohci_writel (ohci, RH_HS_DRWE, &ohci->regs->roothub.status);
696
697 /* Choose the interrupts we care about now, others later on demand */
698 mask = OHCI_INTR_INIT;
699 ohci_writel (ohci, ~0, &ohci->regs->intrstatus);
700 ohci_writel (ohci, mask, &ohci->regs->intrenable);
701
702 /* handle root hub init quirks ... */
703 val = roothub_a (ohci);
704 val &= ~(RH_A_PSM | RH_A_OCPM);
705 if (ohci->flags & OHCI_QUIRK_SUPERIO) {
706 /* NSC 87560 and maybe others */
707 val |= RH_A_NOCP;
708 val &= ~(RH_A_POTPGT | RH_A_NPS);
709 ohci_writel (ohci, val, &ohci->regs->roothub.a);
710 } else if ((ohci->flags & OHCI_QUIRK_AMD756) ||
711 (ohci->flags & OHCI_QUIRK_HUB_POWER)) {
712 /* hub power always on; required for AMD-756 and some
713 * Mac platforms. ganged overcurrent reporting, if any.
714 */
715 val |= RH_A_NPS;
716 ohci_writel (ohci, val, &ohci->regs->roothub.a);
717 }
718 ohci_writel (ohci, RH_HS_LPSC, &ohci->regs->roothub.status);
719 ohci_writel (ohci, (val & RH_A_NPS) ? 0 : RH_B_PPCM,
720 &ohci->regs->roothub.b);
721 // flush those writes
722 (void) ohci_readl (ohci, &ohci->regs->control);
723
724 ohci->next_statechange = jiffies + STATECHANGE_DELAY;
725 spin_unlock_irq (&ohci->lock);
726
727 // POTPGT delay is bits 24-31, in 2 ms units.
728 mdelay ((val >> 23) & 0x1fe);
729 hcd->state = HC_STATE_RUNNING;
730
731 if (quirk_zfmicro(ohci)) {
732 /* Create timer to watch for bad queue state on ZF Micro */
733 setup_timer(&ohci->unlink_watchdog, unlink_watchdog_func,
734 (unsigned long) ohci);
735
736 ohci->eds_scheduled = 0;
737 ohci->ed_to_check = NULL;
738 }
739
740 ohci_dump (ohci, 1);
741
742 return 0;
743 }
744
745 /*-------------------------------------------------------------------------*/
746
747 /* an interrupt happens */
748
ohci_irq(struct usb_hcd * hcd)749 static irqreturn_t ohci_irq (struct usb_hcd *hcd)
750 {
751 struct ohci_hcd *ohci = hcd_to_ohci (hcd);
752 struct ohci_regs __iomem *regs = ohci->regs;
753 int ints;
754
755 /* Read interrupt status (and flush pending writes). We ignore the
756 * optimization of checking the LSB of hcca->done_head; it doesn't
757 * work on all systems (edge triggering for OHCI can be a factor).
758 */
759 ints = ohci_readl(ohci, ®s->intrstatus);
760
761 /* Check for an all 1's result which is a typical consequence
762 * of dead, unclocked, or unplugged (CardBus...) devices
763 */
764 if (ints == ~(u32)0) {
765 disable (ohci);
766 ohci_dbg (ohci, "device removed!\n");
767 return IRQ_HANDLED;
768 }
769
770 /* We only care about interrupts that are enabled */
771 ints &= ohci_readl(ohci, ®s->intrenable);
772
773 /* interrupt for some other device? */
774 if (ints == 0)
775 return IRQ_NOTMINE;
776
777 if (ints & OHCI_INTR_UE) {
778 // e.g. due to PCI Master/Target Abort
779 if (quirk_nec(ohci)) {
780 /* Workaround for a silicon bug in some NEC chips used
781 * in Apple's PowerBooks. Adapted from Darwin code.
782 */
783 ohci_err (ohci, "OHCI Unrecoverable Error, scheduling NEC chip restart\n");
784
785 ohci_writel (ohci, OHCI_INTR_UE, ®s->intrdisable);
786
787 schedule_work (&ohci->nec_work);
788 } else {
789 disable (ohci);
790 ohci_err (ohci, "OHCI Unrecoverable Error, disabled\n");
791 }
792
793 ohci_dump (ohci, 1);
794 ohci_usb_reset (ohci);
795 }
796
797 if (ints & OHCI_INTR_RHSC) {
798 ohci_vdbg(ohci, "rhsc\n");
799 ohci->next_statechange = jiffies + STATECHANGE_DELAY;
800 ohci_writel(ohci, OHCI_INTR_RD | OHCI_INTR_RHSC,
801 ®s->intrstatus);
802
803 /* NOTE: Vendors didn't always make the same implementation
804 * choices for RHSC. Many followed the spec; RHSC triggers
805 * on an edge, like setting and maybe clearing a port status
806 * change bit. With others it's level-triggered, active
807 * until khubd clears all the port status change bits. We'll
808 * always disable it here and rely on polling until khubd
809 * re-enables it.
810 */
811 ohci_writel(ohci, OHCI_INTR_RHSC, ®s->intrdisable);
812 usb_hcd_poll_rh_status(hcd);
813 }
814
815 /* For connect and disconnect events, we expect the controller
816 * to turn on RHSC along with RD. But for remote wakeup events
817 * this might not happen.
818 */
819 else if (ints & OHCI_INTR_RD) {
820 ohci_vdbg(ohci, "resume detect\n");
821 ohci_writel(ohci, OHCI_INTR_RD, ®s->intrstatus);
822 set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
823 if (ohci->autostop) {
824 spin_lock (&ohci->lock);
825 ohci_rh_resume (ohci);
826 spin_unlock (&ohci->lock);
827 } else
828 usb_hcd_resume_root_hub(hcd);
829 }
830
831 if (ints & OHCI_INTR_WDH) {
832 spin_lock (&ohci->lock);
833 dl_done_list (ohci);
834 spin_unlock (&ohci->lock);
835 }
836
837 if (quirk_zfmicro(ohci) && (ints & OHCI_INTR_SF)) {
838 spin_lock(&ohci->lock);
839 if (ohci->ed_to_check) {
840 struct ed *ed = ohci->ed_to_check;
841
842 if (check_ed(ohci, ed)) {
843 /* HC thinks the TD list is empty; HCD knows
844 * at least one TD is outstanding
845 */
846 if (--ohci->zf_delay == 0) {
847 struct td *td = list_entry(
848 ed->td_list.next,
849 struct td, td_list);
850 ohci_warn(ohci,
851 "Reclaiming orphan TD %p\n",
852 td);
853 takeback_td(ohci, td);
854 ohci->ed_to_check = NULL;
855 }
856 } else
857 ohci->ed_to_check = NULL;
858 }
859 spin_unlock(&ohci->lock);
860 }
861
862 /* could track INTR_SO to reduce available PCI/... bandwidth */
863
864 /* handle any pending URB/ED unlinks, leaving INTR_SF enabled
865 * when there's still unlinking to be done (next frame).
866 */
867 spin_lock (&ohci->lock);
868 if (ohci->ed_rm_list)
869 finish_unlinks (ohci, ohci_frame_no(ohci));
870 if ((ints & OHCI_INTR_SF) != 0
871 && !ohci->ed_rm_list
872 && !ohci->ed_to_check
873 && HC_IS_RUNNING(hcd->state))
874 ohci_writel (ohci, OHCI_INTR_SF, ®s->intrdisable);
875 spin_unlock (&ohci->lock);
876
877 if (HC_IS_RUNNING(hcd->state)) {
878 ohci_writel (ohci, ints, ®s->intrstatus);
879 ohci_writel (ohci, OHCI_INTR_MIE, ®s->intrenable);
880 // flush those writes
881 (void) ohci_readl (ohci, &ohci->regs->control);
882 }
883
884 return IRQ_HANDLED;
885 }
886
887 /*-------------------------------------------------------------------------*/
888
ohci_stop(struct usb_hcd * hcd)889 static void ohci_stop (struct usb_hcd *hcd)
890 {
891 struct ohci_hcd *ohci = hcd_to_ohci (hcd);
892
893 ohci_dump (ohci, 1);
894
895 if (quirk_nec(ohci))
896 flush_work_sync(&ohci->nec_work);
897
898 ohci_usb_reset (ohci);
899 ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
900 free_irq(hcd->irq, hcd);
901 hcd->irq = -1;
902
903 if (quirk_zfmicro(ohci))
904 del_timer(&ohci->unlink_watchdog);
905 if (quirk_amdiso(ohci))
906 usb_amd_dev_put();
907
908 remove_debug_files (ohci);
909 ohci_mem_cleanup (ohci);
910 if (ohci->hcca) {
911 dma_free_coherent (hcd->self.controller,
912 sizeof *ohci->hcca,
913 ohci->hcca, ohci->hcca_dma);
914 ohci->hcca = NULL;
915 ohci->hcca_dma = 0;
916 }
917 }
918
919 /*-------------------------------------------------------------------------*/
920
921 #if defined(CONFIG_PM) || defined(CONFIG_PCI)
922
923 /* must not be called from interrupt context */
ohci_restart(struct ohci_hcd * ohci)924 static int ohci_restart (struct ohci_hcd *ohci)
925 {
926 int temp;
927 int i;
928 struct urb_priv *priv;
929
930 spin_lock_irq(&ohci->lock);
931 disable (ohci);
932
933 /* Recycle any "live" eds/tds (and urbs). */
934 if (!list_empty (&ohci->pending))
935 ohci_dbg(ohci, "abort schedule...\n");
936 list_for_each_entry (priv, &ohci->pending, pending) {
937 struct urb *urb = priv->td[0]->urb;
938 struct ed *ed = priv->ed;
939
940 switch (ed->state) {
941 case ED_OPER:
942 ed->state = ED_UNLINK;
943 ed->hwINFO |= cpu_to_hc32(ohci, ED_DEQUEUE);
944 ed_deschedule (ohci, ed);
945
946 ed->ed_next = ohci->ed_rm_list;
947 ed->ed_prev = NULL;
948 ohci->ed_rm_list = ed;
949 /* FALLTHROUGH */
950 case ED_UNLINK:
951 break;
952 default:
953 ohci_dbg(ohci, "bogus ed %p state %d\n",
954 ed, ed->state);
955 }
956
957 if (!urb->unlinked)
958 urb->unlinked = -ESHUTDOWN;
959 }
960 finish_unlinks (ohci, 0);
961 spin_unlock_irq(&ohci->lock);
962
963 /* paranoia, in case that didn't work: */
964
965 /* empty the interrupt branches */
966 for (i = 0; i < NUM_INTS; i++) ohci->load [i] = 0;
967 for (i = 0; i < NUM_INTS; i++) ohci->hcca->int_table [i] = 0;
968
969 /* no EDs to remove */
970 ohci->ed_rm_list = NULL;
971
972 /* empty control and bulk lists */
973 ohci->ed_controltail = NULL;
974 ohci->ed_bulktail = NULL;
975
976 if ((temp = ohci_run (ohci)) < 0) {
977 ohci_err (ohci, "can't restart, %d\n", temp);
978 return temp;
979 }
980 ohci_dbg(ohci, "restart complete\n");
981 return 0;
982 }
983
984 #endif
985
986 /*-------------------------------------------------------------------------*/
987
988 MODULE_AUTHOR (DRIVER_AUTHOR);
989 MODULE_DESCRIPTION(DRIVER_DESC);
990 MODULE_LICENSE ("GPL");
991
992 #ifdef CONFIG_PCI
993 #include "ohci-pci.c"
994 #define PCI_DRIVER ohci_pci_driver
995 #endif
996
997 #if defined(CONFIG_ARCH_SA1100) && defined(CONFIG_SA1111)
998 #include "ohci-sa1111.c"
999 #define SA1111_DRIVER ohci_hcd_sa1111_driver
1000 #endif
1001
1002 #if defined(CONFIG_ARCH_S3C2410) || defined(CONFIG_ARCH_S3C64XX)
1003 #include "ohci-s3c2410.c"
1004 #define PLATFORM_DRIVER ohci_hcd_s3c2410_driver
1005 #endif
1006
1007 #ifdef CONFIG_USB_OHCI_HCD_OMAP1
1008 #include "ohci-omap.c"
1009 #define OMAP1_PLATFORM_DRIVER ohci_hcd_omap_driver
1010 #endif
1011
1012 #ifdef CONFIG_USB_OHCI_HCD_OMAP3
1013 #include "ohci-omap3.c"
1014 #define OMAP3_PLATFORM_DRIVER ohci_hcd_omap3_driver
1015 #endif
1016
1017 #if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
1018 #include "ohci-pxa27x.c"
1019 #define PLATFORM_DRIVER ohci_hcd_pxa27x_driver
1020 #endif
1021
1022 #ifdef CONFIG_ARCH_EP93XX
1023 #include "ohci-ep93xx.c"
1024 #define PLATFORM_DRIVER ohci_hcd_ep93xx_driver
1025 #endif
1026
1027 #ifdef CONFIG_MIPS_ALCHEMY
1028 #include "ohci-au1xxx.c"
1029 #define PLATFORM_DRIVER ohci_hcd_au1xxx_driver
1030 #endif
1031
1032 #ifdef CONFIG_PNX8550
1033 #include "ohci-pnx8550.c"
1034 #define PLATFORM_DRIVER ohci_hcd_pnx8550_driver
1035 #endif
1036
1037 #ifdef CONFIG_USB_OHCI_HCD_PPC_SOC
1038 #include "ohci-ppc-soc.c"
1039 #define PLATFORM_DRIVER ohci_hcd_ppc_soc_driver
1040 #endif
1041
1042 #ifdef CONFIG_ARCH_AT91
1043 #include "ohci-at91.c"
1044 #define PLATFORM_DRIVER ohci_hcd_at91_driver
1045 #endif
1046
1047 #ifdef CONFIG_ARCH_PNX4008
1048 #include "ohci-pnx4008.c"
1049 #define PLATFORM_DRIVER usb_hcd_pnx4008_driver
1050 #endif
1051
1052 #ifdef CONFIG_ARCH_DAVINCI_DA8XX
1053 #include "ohci-da8xx.c"
1054 #define PLATFORM_DRIVER ohci_hcd_da8xx_driver
1055 #endif
1056
1057 #ifdef CONFIG_USB_OHCI_SH
1058 #include "ohci-sh.c"
1059 #define PLATFORM_DRIVER ohci_hcd_sh_driver
1060 #endif
1061
1062
1063 #ifdef CONFIG_USB_OHCI_HCD_PPC_OF
1064 #include "ohci-ppc-of.c"
1065 #define OF_PLATFORM_DRIVER ohci_hcd_ppc_of_driver
1066 #endif
1067
1068 #ifdef CONFIG_PLAT_SPEAR
1069 #include "ohci-spear.c"
1070 #define PLATFORM_DRIVER spear_ohci_hcd_driver
1071 #endif
1072
1073 #ifdef CONFIG_PPC_PS3
1074 #include "ohci-ps3.c"
1075 #define PS3_SYSTEM_BUS_DRIVER ps3_ohci_driver
1076 #endif
1077
1078 #ifdef CONFIG_USB_OHCI_HCD_SSB
1079 #include "ohci-ssb.c"
1080 #define SSB_OHCI_DRIVER ssb_ohci_driver
1081 #endif
1082
1083 #ifdef CONFIG_MFD_SM501
1084 #include "ohci-sm501.c"
1085 #define SM501_OHCI_DRIVER ohci_hcd_sm501_driver
1086 #endif
1087
1088 #ifdef CONFIG_MFD_TC6393XB
1089 #include "ohci-tmio.c"
1090 #define TMIO_OHCI_DRIVER ohci_hcd_tmio_driver
1091 #endif
1092
1093 #ifdef CONFIG_MACH_JZ4740
1094 #include "ohci-jz4740.c"
1095 #define PLATFORM_DRIVER ohci_hcd_jz4740_driver
1096 #endif
1097
1098 #ifdef CONFIG_USB_OCTEON_OHCI
1099 #include "ohci-octeon.c"
1100 #define PLATFORM_DRIVER ohci_octeon_driver
1101 #endif
1102
1103 #ifdef CONFIG_USB_CNS3XXX_OHCI
1104 #include "ohci-cns3xxx.c"
1105 #define PLATFORM_DRIVER ohci_hcd_cns3xxx_driver
1106 #endif
1107
1108 #if !defined(PCI_DRIVER) && \
1109 !defined(PLATFORM_DRIVER) && \
1110 !defined(OMAP1_PLATFORM_DRIVER) && \
1111 !defined(OMAP3_PLATFORM_DRIVER) && \
1112 !defined(OF_PLATFORM_DRIVER) && \
1113 !defined(SA1111_DRIVER) && \
1114 !defined(PS3_SYSTEM_BUS_DRIVER) && \
1115 !defined(SM501_OHCI_DRIVER) && \
1116 !defined(TMIO_OHCI_DRIVER) && \
1117 !defined(SSB_OHCI_DRIVER)
1118 #error "missing bus glue for ohci-hcd"
1119 #endif
1120
ohci_hcd_mod_init(void)1121 static int __init ohci_hcd_mod_init(void)
1122 {
1123 int retval = 0;
1124
1125 if (usb_disabled())
1126 return -ENODEV;
1127
1128 printk(KERN_INFO "%s: " DRIVER_DESC "\n", hcd_name);
1129 pr_debug ("%s: block sizes: ed %Zd td %Zd\n", hcd_name,
1130 sizeof (struct ed), sizeof (struct td));
1131 set_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
1132
1133 #ifdef DEBUG
1134 ohci_debug_root = debugfs_create_dir("ohci", usb_debug_root);
1135 if (!ohci_debug_root) {
1136 retval = -ENOENT;
1137 goto error_debug;
1138 }
1139 #endif
1140
1141 #ifdef PS3_SYSTEM_BUS_DRIVER
1142 retval = ps3_ohci_driver_register(&PS3_SYSTEM_BUS_DRIVER);
1143 if (retval < 0)
1144 goto error_ps3;
1145 #endif
1146
1147 #ifdef PLATFORM_DRIVER
1148 retval = platform_driver_register(&PLATFORM_DRIVER);
1149 if (retval < 0)
1150 goto error_platform;
1151 #endif
1152
1153 #ifdef OMAP1_PLATFORM_DRIVER
1154 retval = platform_driver_register(&OMAP1_PLATFORM_DRIVER);
1155 if (retval < 0)
1156 goto error_omap1_platform;
1157 #endif
1158
1159 #ifdef OMAP3_PLATFORM_DRIVER
1160 retval = platform_driver_register(&OMAP3_PLATFORM_DRIVER);
1161 if (retval < 0)
1162 goto error_omap3_platform;
1163 #endif
1164
1165 #ifdef OF_PLATFORM_DRIVER
1166 retval = platform_driver_register(&OF_PLATFORM_DRIVER);
1167 if (retval < 0)
1168 goto error_of_platform;
1169 #endif
1170
1171 #ifdef SA1111_DRIVER
1172 retval = sa1111_driver_register(&SA1111_DRIVER);
1173 if (retval < 0)
1174 goto error_sa1111;
1175 #endif
1176
1177 #ifdef PCI_DRIVER
1178 retval = pci_register_driver(&PCI_DRIVER);
1179 if (retval < 0)
1180 goto error_pci;
1181 #endif
1182
1183 #ifdef SSB_OHCI_DRIVER
1184 retval = ssb_driver_register(&SSB_OHCI_DRIVER);
1185 if (retval)
1186 goto error_ssb;
1187 #endif
1188
1189 #ifdef SM501_OHCI_DRIVER
1190 retval = platform_driver_register(&SM501_OHCI_DRIVER);
1191 if (retval < 0)
1192 goto error_sm501;
1193 #endif
1194
1195 #ifdef TMIO_OHCI_DRIVER
1196 retval = platform_driver_register(&TMIO_OHCI_DRIVER);
1197 if (retval < 0)
1198 goto error_tmio;
1199 #endif
1200
1201 return retval;
1202
1203 /* Error path */
1204 #ifdef TMIO_OHCI_DRIVER
1205 platform_driver_unregister(&TMIO_OHCI_DRIVER);
1206 error_tmio:
1207 #endif
1208 #ifdef SM501_OHCI_DRIVER
1209 platform_driver_unregister(&SM501_OHCI_DRIVER);
1210 error_sm501:
1211 #endif
1212 #ifdef SSB_OHCI_DRIVER
1213 ssb_driver_unregister(&SSB_OHCI_DRIVER);
1214 error_ssb:
1215 #endif
1216 #ifdef PCI_DRIVER
1217 pci_unregister_driver(&PCI_DRIVER);
1218 error_pci:
1219 #endif
1220 #ifdef SA1111_DRIVER
1221 sa1111_driver_unregister(&SA1111_DRIVER);
1222 error_sa1111:
1223 #endif
1224 #ifdef OF_PLATFORM_DRIVER
1225 platform_driver_unregister(&OF_PLATFORM_DRIVER);
1226 error_of_platform:
1227 #endif
1228 #ifdef PLATFORM_DRIVER
1229 platform_driver_unregister(&PLATFORM_DRIVER);
1230 error_platform:
1231 #endif
1232 #ifdef OMAP1_PLATFORM_DRIVER
1233 platform_driver_unregister(&OMAP1_PLATFORM_DRIVER);
1234 error_omap1_platform:
1235 #endif
1236 #ifdef OMAP3_PLATFORM_DRIVER
1237 platform_driver_unregister(&OMAP3_PLATFORM_DRIVER);
1238 error_omap3_platform:
1239 #endif
1240 #ifdef PS3_SYSTEM_BUS_DRIVER
1241 ps3_ohci_driver_unregister(&PS3_SYSTEM_BUS_DRIVER);
1242 error_ps3:
1243 #endif
1244 #ifdef DEBUG
1245 debugfs_remove(ohci_debug_root);
1246 ohci_debug_root = NULL;
1247 error_debug:
1248 #endif
1249
1250 clear_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
1251 return retval;
1252 }
1253 module_init(ohci_hcd_mod_init);
1254
ohci_hcd_mod_exit(void)1255 static void __exit ohci_hcd_mod_exit(void)
1256 {
1257 #ifdef TMIO_OHCI_DRIVER
1258 platform_driver_unregister(&TMIO_OHCI_DRIVER);
1259 #endif
1260 #ifdef SM501_OHCI_DRIVER
1261 platform_driver_unregister(&SM501_OHCI_DRIVER);
1262 #endif
1263 #ifdef SSB_OHCI_DRIVER
1264 ssb_driver_unregister(&SSB_OHCI_DRIVER);
1265 #endif
1266 #ifdef PCI_DRIVER
1267 pci_unregister_driver(&PCI_DRIVER);
1268 #endif
1269 #ifdef SA1111_DRIVER
1270 sa1111_driver_unregister(&SA1111_DRIVER);
1271 #endif
1272 #ifdef OF_PLATFORM_DRIVER
1273 platform_driver_unregister(&OF_PLATFORM_DRIVER);
1274 #endif
1275 #ifdef PLATFORM_DRIVER
1276 platform_driver_unregister(&PLATFORM_DRIVER);
1277 #endif
1278 #ifdef OMAP3_PLATFORM_DRIVER
1279 platform_driver_unregister(&OMAP3_PLATFORM_DRIVER);
1280 #endif
1281 #ifdef PS3_SYSTEM_BUS_DRIVER
1282 ps3_ohci_driver_unregister(&PS3_SYSTEM_BUS_DRIVER);
1283 #endif
1284 #ifdef DEBUG
1285 debugfs_remove(ohci_debug_root);
1286 #endif
1287 clear_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
1288 }
1289 module_exit(ohci_hcd_mod_exit);
1290
1291