1 /****************************************************************************
2  * Driver for Solarflare Solarstorm network controllers and boards
3  * Copyright 2005 Fen Systems Ltd.
4  * Copyright 2006-2010 Solarflare Communications Inc.
5  *
6  * This program is free software; you can redistribute it and/or modify it
7  * under the terms of the GNU General Public License version 2 as published
8  * by the Free Software Foundation, incorporated herein by reference.
9  */
10 
11 #ifndef EFX_SPI_H
12 #define EFX_SPI_H
13 
14 #include "net_driver.h"
15 
16 /**************************************************************************
17  *
18  * Basic SPI command set and bit definitions
19  *
20  *************************************************************************/
21 
22 #define SPI_WRSR 0x01		/* Write status register */
23 #define SPI_WRITE 0x02		/* Write data to memory array */
24 #define SPI_READ 0x03		/* Read data from memory array */
25 #define SPI_WRDI 0x04		/* Reset write enable latch */
26 #define SPI_RDSR 0x05		/* Read status register */
27 #define SPI_WREN 0x06		/* Set write enable latch */
28 #define SPI_SST_EWSR 0x50	/* SST: Enable write to status register */
29 
30 #define SPI_STATUS_WPEN 0x80	/* Write-protect pin enabled */
31 #define SPI_STATUS_BP2 0x10	/* Block protection bit 2 */
32 #define SPI_STATUS_BP1 0x08	/* Block protection bit 1 */
33 #define SPI_STATUS_BP0 0x04	/* Block protection bit 0 */
34 #define SPI_STATUS_WEN 0x02	/* State of the write enable latch */
35 #define SPI_STATUS_NRDY 0x01	/* Device busy flag */
36 
37 /**
38  * struct efx_spi_device - an Efx SPI (Serial Peripheral Interface) device
39  * @device_id:		Controller's id for the device
40  * @size:		Size (in bytes)
41  * @addr_len:		Number of address bytes in read/write commands
42  * @munge_address:	Flag whether addresses should be munged.
43  *	Some devices with 9-bit addresses (e.g. AT25040A EEPROM)
44  *	use bit 3 of the command byte as address bit A8, rather
45  *	than having a two-byte address.  If this flag is set, then
46  *	commands should be munged in this way.
47  * @erase_command:	Erase command (or 0 if sector erase not needed).
48  * @erase_size:		Erase sector size (in bytes)
49  *	Erase commands affect sectors with this size and alignment.
50  *	This must be a power of two.
51  * @block_size:		Write block size (in bytes).
52  *	Write commands are limited to blocks with this size and alignment.
53  */
54 struct efx_spi_device {
55 	int device_id;
56 	unsigned int size;
57 	unsigned int addr_len;
58 	unsigned int munge_address:1;
59 	u8 erase_command;
60 	unsigned int erase_size;
61 	unsigned int block_size;
62 };
63 
efx_spi_present(const struct efx_spi_device * spi)64 static inline bool efx_spi_present(const struct efx_spi_device *spi)
65 {
66 	return spi->size != 0;
67 }
68 
69 int falcon_spi_cmd(struct efx_nic *efx,
70 		   const struct efx_spi_device *spi, unsigned int command,
71 		   int address, const void *in, void *out, size_t len);
72 int falcon_spi_wait_write(struct efx_nic *efx,
73 			  const struct efx_spi_device *spi);
74 int falcon_spi_read(struct efx_nic *efx,
75 		    const struct efx_spi_device *spi, loff_t start,
76 		    size_t len, size_t *retlen, u8 *buffer);
77 int falcon_spi_write(struct efx_nic *efx,
78 		     const struct efx_spi_device *spi, loff_t start,
79 		     size_t len, size_t *retlen, const u8 *buffer);
80 
81 /*
82  * SFC4000 flash is partitioned into:
83  *     0-0x400       chip and board config (see falcon_hwdefs.h)
84  *     0x400-0x8000  unused (or may contain VPD if EEPROM not present)
85  *     0x8000-end    boot code (mapped to PCI expansion ROM)
86  * SFC4000 small EEPROM (size < 0x400) is used for VPD only.
87  * SFC4000 large EEPROM (size >= 0x400) is partitioned into:
88  *     0-0x400       chip and board config
89  *     configurable  VPD
90  *     0x800-0x1800  boot config
91  * Aside from the chip and board config, all of these are optional and may
92  * be absent or truncated depending on the devices used.
93  */
94 #define FALCON_NVCONFIG_END 0x400U
95 #define FALCON_FLASH_BOOTCODE_START 0x8000U
96 #define EFX_EEPROM_BOOTCONFIG_START 0x800U
97 #define EFX_EEPROM_BOOTCONFIG_END 0x1800U
98 
99 #endif /* EFX_SPI_H */
100