1 // SPDX-License-Identifier: GPL-2.0
2 /* Copyright (c) 2018 Intel Corporation */
3
4 #include "igc_phy.h"
5
6 /**
7 * igc_check_reset_block - Check if PHY reset is blocked
8 * @hw: pointer to the HW structure
9 *
10 * Read the PHY management control register and check whether a PHY reset
11 * is blocked. If a reset is not blocked return 0, otherwise
12 * return IGC_ERR_BLK_PHY_RESET (12).
13 */
igc_check_reset_block(struct igc_hw * hw)14 s32 igc_check_reset_block(struct igc_hw *hw)
15 {
16 u32 manc;
17
18 manc = rd32(IGC_MANC);
19
20 return (manc & IGC_MANC_BLK_PHY_RST_ON_IDE) ?
21 IGC_ERR_BLK_PHY_RESET : 0;
22 }
23
24 /**
25 * igc_get_phy_id - Retrieve the PHY ID and revision
26 * @hw: pointer to the HW structure
27 *
28 * Reads the PHY registers and stores the PHY ID and possibly the PHY
29 * revision in the hardware structure.
30 */
igc_get_phy_id(struct igc_hw * hw)31 s32 igc_get_phy_id(struct igc_hw *hw)
32 {
33 struct igc_phy_info *phy = &hw->phy;
34 s32 ret_val = 0;
35 u16 phy_id;
36
37 ret_val = phy->ops.read_reg(hw, PHY_ID1, &phy_id);
38 if (ret_val)
39 goto out;
40
41 phy->id = (u32)(phy_id << 16);
42 usleep_range(200, 500);
43 ret_val = phy->ops.read_reg(hw, PHY_ID2, &phy_id);
44 if (ret_val)
45 goto out;
46
47 phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
48 phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
49
50 out:
51 return ret_val;
52 }
53
54 /**
55 * igc_phy_has_link - Polls PHY for link
56 * @hw: pointer to the HW structure
57 * @iterations: number of times to poll for link
58 * @usec_interval: delay between polling attempts
59 * @success: pointer to whether polling was successful or not
60 *
61 * Polls the PHY status register for link, 'iterations' number of times.
62 */
igc_phy_has_link(struct igc_hw * hw,u32 iterations,u32 usec_interval,bool * success)63 s32 igc_phy_has_link(struct igc_hw *hw, u32 iterations,
64 u32 usec_interval, bool *success)
65 {
66 u16 i, phy_status;
67 s32 ret_val = 0;
68
69 for (i = 0; i < iterations; i++) {
70 /* Some PHYs require the PHY_STATUS register to be read
71 * twice due to the link bit being sticky. No harm doing
72 * it across the board.
73 */
74 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
75 if (ret_val && usec_interval > 0) {
76 /* If the first read fails, another entity may have
77 * ownership of the resources, wait and try again to
78 * see if they have relinquished the resources yet.
79 */
80 if (usec_interval >= 1000)
81 mdelay(usec_interval / 1000);
82 else
83 udelay(usec_interval);
84 }
85 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
86 if (ret_val)
87 break;
88 if (phy_status & MII_SR_LINK_STATUS)
89 break;
90 if (usec_interval >= 1000)
91 mdelay(usec_interval / 1000);
92 else
93 udelay(usec_interval);
94 }
95
96 *success = (i < iterations) ? true : false;
97
98 return ret_val;
99 }
100
101 /**
102 * igc_power_up_phy_copper - Restore copper link in case of PHY power down
103 * @hw: pointer to the HW structure
104 *
105 * In the case of a PHY power down to save power, or to turn off link during a
106 * driver unload, restore the link to previous settings.
107 */
igc_power_up_phy_copper(struct igc_hw * hw)108 void igc_power_up_phy_copper(struct igc_hw *hw)
109 {
110 u16 mii_reg = 0;
111
112 /* The PHY will retain its settings across a power down/up cycle */
113 hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg);
114 mii_reg &= ~MII_CR_POWER_DOWN;
115 hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg);
116 }
117
118 /**
119 * igc_power_down_phy_copper - Power down copper PHY
120 * @hw: pointer to the HW structure
121 *
122 * Power down PHY to save power when interface is down and wake on lan
123 * is not enabled.
124 */
igc_power_down_phy_copper(struct igc_hw * hw)125 void igc_power_down_phy_copper(struct igc_hw *hw)
126 {
127 u16 mii_reg = 0;
128
129 /* The PHY will retain its settings across a power down/up cycle */
130 hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg);
131 mii_reg |= MII_CR_POWER_DOWN;
132
133 /* Temporary workaround - should be removed when PHY will implement
134 * IEEE registers as properly
135 */
136 /* hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg);*/
137 usleep_range(1000, 2000);
138 }
139
140 /**
141 * igc_check_downshift - Checks whether a downshift in speed occurred
142 * @hw: pointer to the HW structure
143 *
144 * A downshift is detected by querying the PHY link health.
145 */
igc_check_downshift(struct igc_hw * hw)146 void igc_check_downshift(struct igc_hw *hw)
147 {
148 struct igc_phy_info *phy = &hw->phy;
149
150 /* speed downshift not supported */
151 phy->speed_downgraded = false;
152 }
153
154 /**
155 * igc_phy_hw_reset - PHY hardware reset
156 * @hw: pointer to the HW structure
157 *
158 * Verify the reset block is not blocking us from resetting. Acquire
159 * semaphore (if necessary) and read/set/write the device control reset
160 * bit in the PHY. Wait the appropriate delay time for the device to
161 * reset and release the semaphore (if necessary).
162 */
igc_phy_hw_reset(struct igc_hw * hw)163 s32 igc_phy_hw_reset(struct igc_hw *hw)
164 {
165 struct igc_phy_info *phy = &hw->phy;
166 u32 phpm = 0, timeout = 10000;
167 s32 ret_val;
168 u32 ctrl;
169
170 ret_val = igc_check_reset_block(hw);
171 if (ret_val) {
172 ret_val = 0;
173 goto out;
174 }
175
176 ret_val = phy->ops.acquire(hw);
177 if (ret_val)
178 goto out;
179
180 phpm = rd32(IGC_I225_PHPM);
181
182 ctrl = rd32(IGC_CTRL);
183 wr32(IGC_CTRL, ctrl | IGC_CTRL_PHY_RST);
184 wrfl();
185
186 udelay(phy->reset_delay_us);
187
188 wr32(IGC_CTRL, ctrl);
189 wrfl();
190
191 /* SW should guarantee 100us for the completion of the PHY reset */
192 usleep_range(100, 150);
193 do {
194 phpm = rd32(IGC_I225_PHPM);
195 timeout--;
196 udelay(1);
197 } while (!(phpm & IGC_PHY_RST_COMP) && timeout);
198
199 if (!timeout)
200 hw_dbg("Timeout is expired after a phy reset\n");
201
202 usleep_range(100, 150);
203
204 phy->ops.release(hw);
205
206 out:
207 return ret_val;
208 }
209
210 /**
211 * igc_phy_setup_autoneg - Configure PHY for auto-negotiation
212 * @hw: pointer to the HW structure
213 *
214 * Reads the MII auto-neg advertisement register and/or the 1000T control
215 * register and if the PHY is already setup for auto-negotiation, then
216 * return successful. Otherwise, setup advertisement and flow control to
217 * the appropriate values for the wanted auto-negotiation.
218 */
igc_phy_setup_autoneg(struct igc_hw * hw)219 static s32 igc_phy_setup_autoneg(struct igc_hw *hw)
220 {
221 struct igc_phy_info *phy = &hw->phy;
222 u16 aneg_multigbt_an_ctrl = 0;
223 u16 mii_1000t_ctrl_reg = 0;
224 u16 mii_autoneg_adv_reg;
225 s32 ret_val;
226
227 phy->autoneg_advertised &= phy->autoneg_mask;
228
229 /* Read the MII Auto-Neg Advertisement Register (Address 4). */
230 ret_val = phy->ops.read_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
231 if (ret_val)
232 return ret_val;
233
234 if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
235 /* Read the MII 1000Base-T Control Register (Address 9). */
236 ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL,
237 &mii_1000t_ctrl_reg);
238 if (ret_val)
239 return ret_val;
240 }
241
242 if (phy->autoneg_mask & ADVERTISE_2500_FULL) {
243 /* Read the MULTI GBT AN Control Register - reg 7.32 */
244 ret_val = phy->ops.read_reg(hw, (STANDARD_AN_REG_MASK <<
245 MMD_DEVADDR_SHIFT) |
246 ANEG_MULTIGBT_AN_CTRL,
247 &aneg_multigbt_an_ctrl);
248
249 if (ret_val)
250 return ret_val;
251 }
252
253 /* Need to parse both autoneg_advertised and fc and set up
254 * the appropriate PHY registers. First we will parse for
255 * autoneg_advertised software override. Since we can advertise
256 * a plethora of combinations, we need to check each bit
257 * individually.
258 */
259
260 /* First we clear all the 10/100 mb speed bits in the Auto-Neg
261 * Advertisement Register (Address 4) and the 1000 mb speed bits in
262 * the 1000Base-T Control Register (Address 9).
263 */
264 mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS |
265 NWAY_AR_100TX_HD_CAPS |
266 NWAY_AR_10T_FD_CAPS |
267 NWAY_AR_10T_HD_CAPS);
268 mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS);
269
270 hw_dbg("autoneg_advertised %x\n", phy->autoneg_advertised);
271
272 /* Do we want to advertise 10 Mb Half Duplex? */
273 if (phy->autoneg_advertised & ADVERTISE_10_HALF) {
274 hw_dbg("Advertise 10mb Half duplex\n");
275 mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
276 }
277
278 /* Do we want to advertise 10 Mb Full Duplex? */
279 if (phy->autoneg_advertised & ADVERTISE_10_FULL) {
280 hw_dbg("Advertise 10mb Full duplex\n");
281 mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
282 }
283
284 /* Do we want to advertise 100 Mb Half Duplex? */
285 if (phy->autoneg_advertised & ADVERTISE_100_HALF) {
286 hw_dbg("Advertise 100mb Half duplex\n");
287 mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
288 }
289
290 /* Do we want to advertise 100 Mb Full Duplex? */
291 if (phy->autoneg_advertised & ADVERTISE_100_FULL) {
292 hw_dbg("Advertise 100mb Full duplex\n");
293 mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
294 }
295
296 /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
297 if (phy->autoneg_advertised & ADVERTISE_1000_HALF)
298 hw_dbg("Advertise 1000mb Half duplex request denied!\n");
299
300 /* Do we want to advertise 1000 Mb Full Duplex? */
301 if (phy->autoneg_advertised & ADVERTISE_1000_FULL) {
302 hw_dbg("Advertise 1000mb Full duplex\n");
303 mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
304 }
305
306 /* We do not allow the Phy to advertise 2500 Mb Half Duplex */
307 if (phy->autoneg_advertised & ADVERTISE_2500_HALF)
308 hw_dbg("Advertise 2500mb Half duplex request denied!\n");
309
310 /* Do we want to advertise 2500 Mb Full Duplex? */
311 if (phy->autoneg_advertised & ADVERTISE_2500_FULL) {
312 hw_dbg("Advertise 2500mb Full duplex\n");
313 aneg_multigbt_an_ctrl |= CR_2500T_FD_CAPS;
314 } else {
315 aneg_multigbt_an_ctrl &= ~CR_2500T_FD_CAPS;
316 }
317
318 /* Check for a software override of the flow control settings, and
319 * setup the PHY advertisement registers accordingly. If
320 * auto-negotiation is enabled, then software will have to set the
321 * "PAUSE" bits to the correct value in the Auto-Negotiation
322 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-
323 * negotiation.
324 *
325 * The possible values of the "fc" parameter are:
326 * 0: Flow control is completely disabled
327 * 1: Rx flow control is enabled (we can receive pause frames
328 * but not send pause frames).
329 * 2: Tx flow control is enabled (we can send pause frames
330 * but we do not support receiving pause frames).
331 * 3: Both Rx and Tx flow control (symmetric) are enabled.
332 * other: No software override. The flow control configuration
333 * in the EEPROM is used.
334 */
335 switch (hw->fc.current_mode) {
336 case igc_fc_none:
337 /* Flow control (Rx & Tx) is completely disabled by a
338 * software over-ride.
339 */
340 mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
341 break;
342 case igc_fc_rx_pause:
343 /* Rx Flow control is enabled, and Tx Flow control is
344 * disabled, by a software over-ride.
345 *
346 * Since there really isn't a way to advertise that we are
347 * capable of Rx Pause ONLY, we will advertise that we
348 * support both symmetric and asymmetric Rx PAUSE. Later
349 * (in igc_config_fc_after_link_up) we will disable the
350 * hw's ability to send PAUSE frames.
351 */
352 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
353 break;
354 case igc_fc_tx_pause:
355 /* Tx Flow control is enabled, and Rx Flow control is
356 * disabled, by a software over-ride.
357 */
358 mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
359 mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
360 break;
361 case igc_fc_full:
362 /* Flow control (both Rx and Tx) is enabled by a software
363 * over-ride.
364 */
365 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
366 break;
367 default:
368 hw_dbg("Flow control param set incorrectly\n");
369 return -IGC_ERR_CONFIG;
370 }
371
372 ret_val = phy->ops.write_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
373 if (ret_val)
374 return ret_val;
375
376 hw_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
377
378 if (phy->autoneg_mask & ADVERTISE_1000_FULL)
379 ret_val = phy->ops.write_reg(hw, PHY_1000T_CTRL,
380 mii_1000t_ctrl_reg);
381
382 if (phy->autoneg_mask & ADVERTISE_2500_FULL)
383 ret_val = phy->ops.write_reg(hw,
384 (STANDARD_AN_REG_MASK <<
385 MMD_DEVADDR_SHIFT) |
386 ANEG_MULTIGBT_AN_CTRL,
387 aneg_multigbt_an_ctrl);
388
389 return ret_val;
390 }
391
392 /**
393 * igc_wait_autoneg - Wait for auto-neg completion
394 * @hw: pointer to the HW structure
395 *
396 * Waits for auto-negotiation to complete or for the auto-negotiation time
397 * limit to expire, which ever happens first.
398 */
igc_wait_autoneg(struct igc_hw * hw)399 static s32 igc_wait_autoneg(struct igc_hw *hw)
400 {
401 u16 i, phy_status;
402 s32 ret_val = 0;
403
404 /* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
405 for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
406 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
407 if (ret_val)
408 break;
409 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
410 if (ret_val)
411 break;
412 if (phy_status & MII_SR_AUTONEG_COMPLETE)
413 break;
414 msleep(100);
415 }
416
417 /* PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation
418 * has completed.
419 */
420 return ret_val;
421 }
422
423 /**
424 * igc_copper_link_autoneg - Setup/Enable autoneg for copper link
425 * @hw: pointer to the HW structure
426 *
427 * Performs initial bounds checking on autoneg advertisement parameter, then
428 * configure to advertise the full capability. Setup the PHY to autoneg
429 * and restart the negotiation process between the link partner. If
430 * autoneg_wait_to_complete, then wait for autoneg to complete before exiting.
431 */
igc_copper_link_autoneg(struct igc_hw * hw)432 static s32 igc_copper_link_autoneg(struct igc_hw *hw)
433 {
434 struct igc_phy_info *phy = &hw->phy;
435 u16 phy_ctrl;
436 s32 ret_val;
437
438 /* Perform some bounds checking on the autoneg advertisement
439 * parameter.
440 */
441 phy->autoneg_advertised &= phy->autoneg_mask;
442
443 /* If autoneg_advertised is zero, we assume it was not defaulted
444 * by the calling code so we set to advertise full capability.
445 */
446 if (phy->autoneg_advertised == 0)
447 phy->autoneg_advertised = phy->autoneg_mask;
448
449 hw_dbg("Reconfiguring auto-neg advertisement params\n");
450 ret_val = igc_phy_setup_autoneg(hw);
451 if (ret_val) {
452 hw_dbg("Error Setting up Auto-Negotiation\n");
453 goto out;
454 }
455 hw_dbg("Restarting Auto-Neg\n");
456
457 /* Restart auto-negotiation by setting the Auto Neg Enable bit and
458 * the Auto Neg Restart bit in the PHY control register.
459 */
460 ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_ctrl);
461 if (ret_val)
462 goto out;
463
464 phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
465 ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_ctrl);
466 if (ret_val)
467 goto out;
468
469 /* Does the user want to wait for Auto-Neg to complete here, or
470 * check at a later time (for example, callback routine).
471 */
472 if (phy->autoneg_wait_to_complete) {
473 ret_val = igc_wait_autoneg(hw);
474 if (ret_val) {
475 hw_dbg("Error while waiting for autoneg to complete\n");
476 goto out;
477 }
478 }
479
480 hw->mac.get_link_status = true;
481
482 out:
483 return ret_val;
484 }
485
486 /**
487 * igc_setup_copper_link - Configure copper link settings
488 * @hw: pointer to the HW structure
489 *
490 * Calls the appropriate function to configure the link for auto-neg or forced
491 * speed and duplex. Then we check for link, once link is established calls
492 * to configure collision distance and flow control are called. If link is
493 * not established, we return -IGC_ERR_PHY (-2).
494 */
igc_setup_copper_link(struct igc_hw * hw)495 s32 igc_setup_copper_link(struct igc_hw *hw)
496 {
497 s32 ret_val = 0;
498 bool link;
499
500 if (hw->mac.autoneg) {
501 /* Setup autoneg and flow control advertisement and perform
502 * autonegotiation.
503 */
504 ret_val = igc_copper_link_autoneg(hw);
505 if (ret_val)
506 goto out;
507 } else {
508 /* PHY will be set to 10H, 10F, 100H or 100F
509 * depending on user settings.
510 */
511 hw_dbg("Forcing Speed and Duplex\n");
512 ret_val = hw->phy.ops.force_speed_duplex(hw);
513 if (ret_val) {
514 hw_dbg("Error Forcing Speed and Duplex\n");
515 goto out;
516 }
517 }
518
519 /* Check link status. Wait up to 100 microseconds for link to become
520 * valid.
521 */
522 ret_val = igc_phy_has_link(hw, COPPER_LINK_UP_LIMIT, 10, &link);
523 if (ret_val)
524 goto out;
525
526 if (link) {
527 hw_dbg("Valid link established!!!\n");
528 igc_config_collision_dist(hw);
529 ret_val = igc_config_fc_after_link_up(hw);
530 } else {
531 hw_dbg("Unable to establish link!!!\n");
532 }
533
534 out:
535 return ret_val;
536 }
537
538 /**
539 * igc_read_phy_reg_mdic - Read MDI control register
540 * @hw: pointer to the HW structure
541 * @offset: register offset to be read
542 * @data: pointer to the read data
543 *
544 * Reads the MDI control register in the PHY at offset and stores the
545 * information read to data.
546 */
igc_read_phy_reg_mdic(struct igc_hw * hw,u32 offset,u16 * data)547 static s32 igc_read_phy_reg_mdic(struct igc_hw *hw, u32 offset, u16 *data)
548 {
549 struct igc_phy_info *phy = &hw->phy;
550 u32 i, mdic = 0;
551 s32 ret_val = 0;
552
553 if (offset > MAX_PHY_REG_ADDRESS) {
554 hw_dbg("PHY Address %d is out of range\n", offset);
555 ret_val = -IGC_ERR_PARAM;
556 goto out;
557 }
558
559 /* Set up Op-code, Phy Address, and register offset in the MDI
560 * Control register. The MAC will take care of interfacing with the
561 * PHY to retrieve the desired data.
562 */
563 mdic = ((offset << IGC_MDIC_REG_SHIFT) |
564 (phy->addr << IGC_MDIC_PHY_SHIFT) |
565 (IGC_MDIC_OP_READ));
566
567 wr32(IGC_MDIC, mdic);
568
569 /* Poll the ready bit to see if the MDI read completed
570 * Increasing the time out as testing showed failures with
571 * the lower time out
572 */
573 for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) {
574 udelay(50);
575 mdic = rd32(IGC_MDIC);
576 if (mdic & IGC_MDIC_READY)
577 break;
578 }
579 if (!(mdic & IGC_MDIC_READY)) {
580 hw_dbg("MDI Read did not complete\n");
581 ret_val = -IGC_ERR_PHY;
582 goto out;
583 }
584 if (mdic & IGC_MDIC_ERROR) {
585 hw_dbg("MDI Error\n");
586 ret_val = -IGC_ERR_PHY;
587 goto out;
588 }
589 *data = (u16)mdic;
590
591 out:
592 return ret_val;
593 }
594
595 /**
596 * igc_write_phy_reg_mdic - Write MDI control register
597 * @hw: pointer to the HW structure
598 * @offset: register offset to write to
599 * @data: data to write to register at offset
600 *
601 * Writes data to MDI control register in the PHY at offset.
602 */
igc_write_phy_reg_mdic(struct igc_hw * hw,u32 offset,u16 data)603 static s32 igc_write_phy_reg_mdic(struct igc_hw *hw, u32 offset, u16 data)
604 {
605 struct igc_phy_info *phy = &hw->phy;
606 u32 i, mdic = 0;
607 s32 ret_val = 0;
608
609 if (offset > MAX_PHY_REG_ADDRESS) {
610 hw_dbg("PHY Address %d is out of range\n", offset);
611 ret_val = -IGC_ERR_PARAM;
612 goto out;
613 }
614
615 /* Set up Op-code, Phy Address, and register offset in the MDI
616 * Control register. The MAC will take care of interfacing with the
617 * PHY to write the desired data.
618 */
619 mdic = (((u32)data) |
620 (offset << IGC_MDIC_REG_SHIFT) |
621 (phy->addr << IGC_MDIC_PHY_SHIFT) |
622 (IGC_MDIC_OP_WRITE));
623
624 wr32(IGC_MDIC, mdic);
625
626 /* Poll the ready bit to see if the MDI read completed
627 * Increasing the time out as testing showed failures with
628 * the lower time out
629 */
630 for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) {
631 udelay(50);
632 mdic = rd32(IGC_MDIC);
633 if (mdic & IGC_MDIC_READY)
634 break;
635 }
636 if (!(mdic & IGC_MDIC_READY)) {
637 hw_dbg("MDI Write did not complete\n");
638 ret_val = -IGC_ERR_PHY;
639 goto out;
640 }
641 if (mdic & IGC_MDIC_ERROR) {
642 hw_dbg("MDI Error\n");
643 ret_val = -IGC_ERR_PHY;
644 goto out;
645 }
646
647 out:
648 return ret_val;
649 }
650
651 /**
652 * __igc_access_xmdio_reg - Read/write XMDIO register
653 * @hw: pointer to the HW structure
654 * @address: XMDIO address to program
655 * @dev_addr: device address to program
656 * @data: pointer to value to read/write from/to the XMDIO address
657 * @read: boolean flag to indicate read or write
658 */
__igc_access_xmdio_reg(struct igc_hw * hw,u16 address,u8 dev_addr,u16 * data,bool read)659 static s32 __igc_access_xmdio_reg(struct igc_hw *hw, u16 address,
660 u8 dev_addr, u16 *data, bool read)
661 {
662 s32 ret_val;
663
664 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, dev_addr);
665 if (ret_val)
666 return ret_val;
667
668 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAAD, address);
669 if (ret_val)
670 return ret_val;
671
672 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, IGC_MMDAC_FUNC_DATA |
673 dev_addr);
674 if (ret_val)
675 return ret_val;
676
677 if (read)
678 ret_val = hw->phy.ops.read_reg(hw, IGC_MMDAAD, data);
679 else
680 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAAD, *data);
681 if (ret_val)
682 return ret_val;
683
684 /* Recalibrate the device back to 0 */
685 ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, 0);
686 if (ret_val)
687 return ret_val;
688
689 return ret_val;
690 }
691
692 /**
693 * igc_read_xmdio_reg - Read XMDIO register
694 * @hw: pointer to the HW structure
695 * @addr: XMDIO address to program
696 * @dev_addr: device address to program
697 * @data: value to be read from the EMI address
698 */
igc_read_xmdio_reg(struct igc_hw * hw,u16 addr,u8 dev_addr,u16 * data)699 static s32 igc_read_xmdio_reg(struct igc_hw *hw, u16 addr,
700 u8 dev_addr, u16 *data)
701 {
702 return __igc_access_xmdio_reg(hw, addr, dev_addr, data, true);
703 }
704
705 /**
706 * igc_write_xmdio_reg - Write XMDIO register
707 * @hw: pointer to the HW structure
708 * @addr: XMDIO address to program
709 * @dev_addr: device address to program
710 * @data: value to be written to the XMDIO address
711 */
igc_write_xmdio_reg(struct igc_hw * hw,u16 addr,u8 dev_addr,u16 data)712 static s32 igc_write_xmdio_reg(struct igc_hw *hw, u16 addr,
713 u8 dev_addr, u16 data)
714 {
715 return __igc_access_xmdio_reg(hw, addr, dev_addr, &data, false);
716 }
717
718 /**
719 * igc_write_phy_reg_gpy - Write GPY PHY register
720 * @hw: pointer to the HW structure
721 * @offset: register offset to write to
722 * @data: data to write at register offset
723 *
724 * Acquires semaphore, if necessary, then writes the data to PHY register
725 * at the offset. Release any acquired semaphores before exiting.
726 */
igc_write_phy_reg_gpy(struct igc_hw * hw,u32 offset,u16 data)727 s32 igc_write_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 data)
728 {
729 u8 dev_addr = (offset & GPY_MMD_MASK) >> GPY_MMD_SHIFT;
730 s32 ret_val;
731
732 offset = offset & GPY_REG_MASK;
733
734 if (!dev_addr) {
735 ret_val = hw->phy.ops.acquire(hw);
736 if (ret_val)
737 return ret_val;
738 ret_val = igc_write_phy_reg_mdic(hw, offset, data);
739 hw->phy.ops.release(hw);
740 } else {
741 ret_val = igc_write_xmdio_reg(hw, (u16)offset, dev_addr,
742 data);
743 }
744
745 return ret_val;
746 }
747
748 /**
749 * igc_read_phy_reg_gpy - Read GPY PHY register
750 * @hw: pointer to the HW structure
751 * @offset: lower half is register offset to read to
752 * upper half is MMD to use.
753 * @data: data to read at register offset
754 *
755 * Acquires semaphore, if necessary, then reads the data in the PHY register
756 * at the offset. Release any acquired semaphores before exiting.
757 */
igc_read_phy_reg_gpy(struct igc_hw * hw,u32 offset,u16 * data)758 s32 igc_read_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 *data)
759 {
760 u8 dev_addr = (offset & GPY_MMD_MASK) >> GPY_MMD_SHIFT;
761 s32 ret_val;
762
763 offset = offset & GPY_REG_MASK;
764
765 if (!dev_addr) {
766 ret_val = hw->phy.ops.acquire(hw);
767 if (ret_val)
768 return ret_val;
769 ret_val = igc_read_phy_reg_mdic(hw, offset, data);
770 hw->phy.ops.release(hw);
771 } else {
772 ret_val = igc_read_xmdio_reg(hw, (u16)offset, dev_addr,
773 data);
774 }
775
776 return ret_val;
777 }
778
779 /**
780 * igc_read_phy_fw_version - Read gPHY firmware version
781 * @hw: pointer to the HW structure
782 */
igc_read_phy_fw_version(struct igc_hw * hw)783 u16 igc_read_phy_fw_version(struct igc_hw *hw)
784 {
785 struct igc_phy_info *phy = &hw->phy;
786 u16 gphy_version = 0;
787 u16 ret_val;
788
789 /* NVM image version is reported as firmware version for i225 device */
790 ret_val = phy->ops.read_reg(hw, IGC_GPHY_VERSION, &gphy_version);
791 if (ret_val)
792 hw_dbg("igc_phy: read wrong gphy version\n");
793
794 return gphy_version;
795 }
796