1 /* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
2 /*
3  * core.h - DesignWare HS OTG Controller common declarations
4  *
5  * Copyright (C) 2004-2013 Synopsys, Inc.
6  */
7 
8 #ifndef __DWC2_CORE_H__
9 #define __DWC2_CORE_H__
10 
11 #include <linux/acpi.h>
12 #include <linux/phy/phy.h>
13 #include <linux/regulator/consumer.h>
14 #include <linux/usb/gadget.h>
15 #include <linux/usb/otg.h>
16 #include <linux/usb/phy.h>
17 #include "hw.h"
18 
19 /*
20  * Suggested defines for tracers:
21  * - no_printk:    Disable tracing
22  * - pr_info:      Print this info to the console
23  * - trace_printk: Print this info to trace buffer (good for verbose logging)
24  */
25 
26 #define DWC2_TRACE_SCHEDULER		no_printk
27 #define DWC2_TRACE_SCHEDULER_VB		no_printk
28 
29 /* Detailed scheduler tracing, but won't overwhelm console */
30 #define dwc2_sch_dbg(hsotg, fmt, ...)					\
31 	DWC2_TRACE_SCHEDULER(pr_fmt("%s: SCH: " fmt),			\
32 			     dev_name(hsotg->dev), ##__VA_ARGS__)
33 
34 /* Verbose scheduler tracing */
35 #define dwc2_sch_vdbg(hsotg, fmt, ...)					\
36 	DWC2_TRACE_SCHEDULER_VB(pr_fmt("%s: SCH: " fmt),		\
37 				dev_name(hsotg->dev), ##__VA_ARGS__)
38 
39 /* Maximum number of Endpoints/HostChannels */
40 #define MAX_EPS_CHANNELS	16
41 
42 /* dwc2-hsotg declarations */
43 static const char * const dwc2_hsotg_supply_names[] = {
44 	"vusb_d",               /* digital USB supply, 1.2V */
45 	"vusb_a",               /* analog USB supply, 1.1V */
46 };
47 
48 #define DWC2_NUM_SUPPLIES ARRAY_SIZE(dwc2_hsotg_supply_names)
49 
50 /*
51  * EP0_MPS_LIMIT
52  *
53  * Unfortunately there seems to be a limit of the amount of data that can
54  * be transferred by IN transactions on EP0. This is either 127 bytes or 3
55  * packets (which practically means 1 packet and 63 bytes of data) when the
56  * MPS is set to 64.
57  *
58  * This means if we are wanting to move >127 bytes of data, we need to
59  * split the transactions up, but just doing one packet at a time does
60  * not work (this may be an implicit DATA0 PID on first packet of the
61  * transaction) and doing 2 packets is outside the controller's limits.
62  *
63  * If we try to lower the MPS size for EP0, then no transfers work properly
64  * for EP0, and the system will fail basic enumeration. As no cause for this
65  * has currently been found, we cannot support any large IN transfers for
66  * EP0.
67  */
68 #define EP0_MPS_LIMIT   64
69 
70 struct dwc2_hsotg;
71 struct dwc2_hsotg_req;
72 
73 /**
74  * struct dwc2_hsotg_ep - driver endpoint definition.
75  * @ep: The gadget layer representation of the endpoint.
76  * @name: The driver generated name for the endpoint.
77  * @queue: Queue of requests for this endpoint.
78  * @parent: Reference back to the parent device structure.
79  * @req: The current request that the endpoint is processing. This is
80  *       used to indicate an request has been loaded onto the endpoint
81  *       and has yet to be completed (maybe due to data move, or simply
82  *       awaiting an ack from the core all the data has been completed).
83  * @debugfs: File entry for debugfs file for this endpoint.
84  * @dir_in: Set to true if this endpoint is of the IN direction, which
85  *          means that it is sending data to the Host.
86  * @map_dir: Set to the value of dir_in when the DMA buffer is mapped.
87  * @index: The index for the endpoint registers.
88  * @mc: Multi Count - number of transactions per microframe
89  * @interval: Interval for periodic endpoints, in frames or microframes.
90  * @name: The name array passed to the USB core.
91  * @halted: Set if the endpoint has been halted.
92  * @periodic: Set if this is a periodic ep, such as Interrupt
93  * @isochronous: Set if this is a isochronous ep
94  * @send_zlp: Set if we need to send a zero-length packet.
95  * @wedged: Set if ep is wedged.
96  * @desc_list_dma: The DMA address of descriptor chain currently in use.
97  * @desc_list: Pointer to descriptor DMA chain head currently in use.
98  * @desc_count: Count of entries within the DMA descriptor chain of EP.
99  * @next_desc: index of next free descriptor in the ISOC chain under SW control.
100  * @compl_desc: index of next descriptor to be completed by xFerComplete
101  * @total_data: The total number of data bytes done.
102  * @fifo_size: The size of the FIFO (for periodic IN endpoints)
103  * @fifo_index: For Dedicated FIFO operation, only FIFO0 can be used for EP0.
104  * @fifo_load: The amount of data loaded into the FIFO (periodic IN)
105  * @last_load: The offset of data for the last start of request.
106  * @size_loaded: The last loaded size for DxEPTSIZE for periodic IN
107  * @target_frame: Targeted frame num to setup next ISOC transfer
108  * @frame_overrun: Indicates SOF number overrun in DSTS
109  *
110  * This is the driver's state for each registered endpoint, allowing it
111  * to keep track of transactions that need doing. Each endpoint has a
112  * lock to protect the state, to try and avoid using an overall lock
113  * for the host controller as much as possible.
114  *
115  * For periodic IN endpoints, we have fifo_size and fifo_load to try
116  * and keep track of the amount of data in the periodic FIFO for each
117  * of these as we don't have a status register that tells us how much
118  * is in each of them. (note, this may actually be useless information
119  * as in shared-fifo mode periodic in acts like a single-frame packet
120  * buffer than a fifo)
121  */
122 struct dwc2_hsotg_ep {
123 	struct usb_ep           ep;
124 	struct list_head        queue;
125 	struct dwc2_hsotg       *parent;
126 	struct dwc2_hsotg_req    *req;
127 	struct dentry           *debugfs;
128 
129 	unsigned long           total_data;
130 	unsigned int            size_loaded;
131 	unsigned int            last_load;
132 	unsigned int            fifo_load;
133 	unsigned short          fifo_size;
134 	unsigned short		fifo_index;
135 
136 	unsigned char           dir_in;
137 	unsigned char           map_dir;
138 	unsigned char           index;
139 	unsigned char           mc;
140 	u16                     interval;
141 
142 	unsigned int            halted:1;
143 	unsigned int            periodic:1;
144 	unsigned int            isochronous:1;
145 	unsigned int            send_zlp:1;
146 	unsigned int            wedged:1;
147 	unsigned int            target_frame;
148 #define TARGET_FRAME_INITIAL   0xFFFFFFFF
149 	bool			frame_overrun;
150 
151 	dma_addr_t		desc_list_dma;
152 	struct dwc2_dma_desc	*desc_list;
153 	u8			desc_count;
154 
155 	unsigned int		next_desc;
156 	unsigned int		compl_desc;
157 
158 	char                    name[10];
159 };
160 
161 /**
162  * struct dwc2_hsotg_req - data transfer request
163  * @req: The USB gadget request
164  * @queue: The list of requests for the endpoint this is queued for.
165  * @saved_req_buf: variable to save req.buf when bounce buffers are used.
166  */
167 struct dwc2_hsotg_req {
168 	struct usb_request      req;
169 	struct list_head        queue;
170 	void *saved_req_buf;
171 };
172 
173 #if IS_ENABLED(CONFIG_USB_DWC2_PERIPHERAL) || \
174 	IS_ENABLED(CONFIG_USB_DWC2_DUAL_ROLE)
175 #define call_gadget(_hs, _entry) \
176 do { \
177 	if ((_hs)->gadget.speed != USB_SPEED_UNKNOWN && \
178 		(_hs)->driver && (_hs)->driver->_entry) { \
179 		spin_unlock(&_hs->lock); \
180 		(_hs)->driver->_entry(&(_hs)->gadget); \
181 		spin_lock(&_hs->lock); \
182 	} \
183 } while (0)
184 #else
185 #define call_gadget(_hs, _entry)	do {} while (0)
186 #endif
187 
188 struct dwc2_hsotg;
189 struct dwc2_host_chan;
190 
191 /* Device States */
192 enum dwc2_lx_state {
193 	DWC2_L0,	/* On state */
194 	DWC2_L1,	/* LPM sleep state */
195 	DWC2_L2,	/* USB suspend state */
196 	DWC2_L3,	/* Off state */
197 };
198 
199 /* Gadget ep0 states */
200 enum dwc2_ep0_state {
201 	DWC2_EP0_SETUP,
202 	DWC2_EP0_DATA_IN,
203 	DWC2_EP0_DATA_OUT,
204 	DWC2_EP0_STATUS_IN,
205 	DWC2_EP0_STATUS_OUT,
206 };
207 
208 /**
209  * struct dwc2_core_params - Parameters for configuring the core
210  *
211  * @otg_caps:           Specifies the OTG capabilities. OTG caps from the platform parameters,
212  *                      used to setup the:
213  *                       - HNP and SRP capable
214  *                       - SRP Only capable
215  *                       - No HNP/SRP capable (always available)
216  *                       Defaults to best available option
217  *                       - OTG revision number the device is compliant with, in binary-coded
218  *                         decimal (i.e. 2.0 is 0200H). (see struct usb_otg_caps)
219  * @host_dma:           Specifies whether to use slave or DMA mode for accessing
220  *                      the data FIFOs. The driver will automatically detect the
221  *                      value for this parameter if none is specified.
222  *                       0 - Slave (always available)
223  *                       1 - DMA (default, if available)
224  * @dma_desc_enable:    When DMA mode is enabled, specifies whether to use
225  *                      address DMA mode or descriptor DMA mode for accessing
226  *                      the data FIFOs. The driver will automatically detect the
227  *                      value for this if none is specified.
228  *                       0 - Address DMA
229  *                       1 - Descriptor DMA (default, if available)
230  * @dma_desc_fs_enable: When DMA mode is enabled, specifies whether to use
231  *                      address DMA mode or descriptor DMA mode for accessing
232  *                      the data FIFOs in Full Speed mode only. The driver
233  *                      will automatically detect the value for this if none is
234  *                      specified.
235  *                       0 - Address DMA
236  *                       1 - Descriptor DMA in FS (default, if available)
237  * @speed:              Specifies the maximum speed of operation in host and
238  *                      device mode. The actual speed depends on the speed of
239  *                      the attached device and the value of phy_type.
240  *                       0 - High Speed
241  *                           (default when phy_type is UTMI+ or ULPI)
242  *                       1 - Full Speed
243  *                           (default when phy_type is Full Speed)
244  * @enable_dynamic_fifo: 0 - Use coreConsultant-specified FIFO size parameters
245  *                       1 - Allow dynamic FIFO sizing (default, if available)
246  * @en_multiple_tx_fifo: Specifies whether dedicated per-endpoint transmit FIFOs
247  *                      are enabled for non-periodic IN endpoints in device
248  *                      mode.
249  * @host_rx_fifo_size:  Number of 4-byte words in the Rx FIFO in host mode when
250  *                      dynamic FIFO sizing is enabled
251  *                       16 to 32768
252  *                      Actual maximum value is autodetected and also
253  *                      the default.
254  * @host_nperio_tx_fifo_size: Number of 4-byte words in the non-periodic Tx FIFO
255  *                      in host mode when dynamic FIFO sizing is enabled
256  *                       16 to 32768
257  *                      Actual maximum value is autodetected and also
258  *                      the default.
259  * @host_perio_tx_fifo_size: Number of 4-byte words in the periodic Tx FIFO in
260  *                      host mode when dynamic FIFO sizing is enabled
261  *                       16 to 32768
262  *                      Actual maximum value is autodetected and also
263  *                      the default.
264  * @max_transfer_size:  The maximum transfer size supported, in bytes
265  *                       2047 to 65,535
266  *                      Actual maximum value is autodetected and also
267  *                      the default.
268  * @max_packet_count:   The maximum number of packets in a transfer
269  *                       15 to 511
270  *                      Actual maximum value is autodetected and also
271  *                      the default.
272  * @host_channels:      The number of host channel registers to use
273  *                       1 to 16
274  *                      Actual maximum value is autodetected and also
275  *                      the default.
276  * @phy_type:           Specifies the type of PHY interface to use. By default,
277  *                      the driver will automatically detect the phy_type.
278  *                       0 - Full Speed Phy
279  *                       1 - UTMI+ Phy
280  *                       2 - ULPI Phy
281  *                      Defaults to best available option (2, 1, then 0)
282  * @phy_utmi_width:     Specifies the UTMI+ Data Width (in bits). This parameter
283  *                      is applicable for a phy_type of UTMI+ or ULPI. (For a
284  *                      ULPI phy_type, this parameter indicates the data width
285  *                      between the MAC and the ULPI Wrapper.) Also, this
286  *                      parameter is applicable only if the OTG_HSPHY_WIDTH cC
287  *                      parameter was set to "8 and 16 bits", meaning that the
288  *                      core has been configured to work at either data path
289  *                      width.
290  *                       8 or 16 (default 16 if available)
291  * @phy_ulpi_ddr:       Specifies whether the ULPI operates at double or single
292  *                      data rate. This parameter is only applicable if phy_type
293  *                      is ULPI.
294  *                       0 - single data rate ULPI interface with 8 bit wide
295  *                           data bus (default)
296  *                       1 - double data rate ULPI interface with 4 bit wide
297  *                           data bus
298  * @phy_ulpi_ext_vbus:  For a ULPI phy, specifies whether to use the internal or
299  *                      external supply to drive the VBus
300  *                       0 - Internal supply (default)
301  *                       1 - External supply
302  * @i2c_enable:         Specifies whether to use the I2Cinterface for a full
303  *                      speed PHY. This parameter is only applicable if phy_type
304  *                      is FS.
305  *                       0 - No (default)
306  *                       1 - Yes
307  * @ipg_isoc_en:        Indicates the IPG supports is enabled or disabled.
308  *                       0 - Disable (default)
309  *                       1 - Enable
310  * @acg_enable:		For enabling Active Clock Gating in the controller
311  *                       0 - No
312  *                       1 - Yes
313  * @ulpi_fs_ls:         Make ULPI phy operate in FS/LS mode only
314  *                       0 - No (default)
315  *                       1 - Yes
316  * @host_support_fs_ls_low_power: Specifies whether low power mode is supported
317  *                      when attached to a Full Speed or Low Speed device in
318  *                      host mode.
319  *                       0 - Don't support low power mode (default)
320  *                       1 - Support low power mode
321  * @host_ls_low_power_phy_clk: Specifies the PHY clock rate in low power mode
322  *                      when connected to a Low Speed device in host
323  *                      mode. This parameter is applicable only if
324  *                      host_support_fs_ls_low_power is enabled.
325  *                       0 - 48 MHz
326  *                           (default when phy_type is UTMI+ or ULPI)
327  *                       1 - 6 MHz
328  *                           (default when phy_type is Full Speed)
329  * @oc_disable:		Flag to disable overcurrent condition.
330  *			0 - Allow overcurrent condition to get detected
331  *			1 - Disable overcurrent condtion to get detected
332  * @ts_dline:           Enable Term Select Dline pulsing
333  *                       0 - No (default)
334  *                       1 - Yes
335  * @reload_ctl:         Allow dynamic reloading of HFIR register during runtime
336  *                       0 - No (default for core < 2.92a)
337  *                       1 - Yes (default for core >= 2.92a)
338  * @ahbcfg:             This field allows the default value of the GAHBCFG
339  *                      register to be overridden
340  *                       -1         - GAHBCFG value will be set to 0x06
341  *                                    (INCR, default)
342  *                       all others - GAHBCFG value will be overridden with
343  *                                    this value
344  *                      Not all bits can be controlled like this, the
345  *                      bits defined by GAHBCFG_CTRL_MASK are controlled
346  *                      by the driver and are ignored in this
347  *                      configuration value.
348  * @uframe_sched:       True to enable the microframe scheduler
349  * @external_id_pin_ctl: Specifies whether ID pin is handled externally.
350  *                      Disable CONIDSTSCHNG controller interrupt in such
351  *                      case.
352  *                      0 - No (default)
353  *                      1 - Yes
354  * @power_down:         Specifies whether the controller support power_down.
355  *			If power_down is enabled, the controller will enter
356  *			power_down in both peripheral and host mode when
357  *			needed.
358  *			0 - No (default)
359  *			1 - Partial power down
360  *			2 - Hibernation
361  * @no_clock_gating:	Specifies whether to avoid clock gating feature.
362  *			0 - No (use clock gating)
363  *			1 - Yes (avoid it)
364  * @lpm:		Enable LPM support.
365  *			0 - No
366  *			1 - Yes
367  * @lpm_clock_gating:		Enable core PHY clock gating.
368  *			0 - No
369  *			1 - Yes
370  * @besl:		Enable LPM Errata support.
371  *			0 - No
372  *			1 - Yes
373  * @hird_threshold_en:	HIRD or HIRD Threshold enable.
374  *			0 - No
375  *			1 - Yes
376  * @hird_threshold:	Value of BESL or HIRD Threshold.
377  * @ref_clk_per:        Indicates in terms of pico seconds the period
378  *                      of ref_clk.
379  *			62500 - 16MHz
380  *                      58823 - 17MHz
381  *                      52083 - 19.2MHz
382  *			50000 - 20MHz
383  *			41666 - 24MHz
384  *			33333 - 30MHz (default)
385  *			25000 - 40MHz
386  * @sof_cnt_wkup_alert: Indicates in term of number of SOF's after which
387  *                      the controller should generate an interrupt if the
388  *                      device had been in L1 state until that period.
389  *                      This is used by SW to initiate Remote WakeUp in the
390  *                      controller so as to sync to the uF number from the host.
391  * @activate_stm_fs_transceiver: Activate internal transceiver using GGPIO
392  *			register.
393  *			0 - Deactivate the transceiver (default)
394  *			1 - Activate the transceiver
395  * @activate_stm_id_vb_detection: Activate external ID pin and Vbus level
396  *			detection using GGPIO register.
397  *			0 - Deactivate the external level detection (default)
398  *			1 - Activate the external level detection
399  * @activate_ingenic_overcurrent_detection: Activate Ingenic overcurrent
400  *			detection.
401  *			0 - Deactivate the overcurrent detection
402  *			1 - Activate the overcurrent detection (default)
403  * @g_dma:              Enables gadget dma usage (default: autodetect).
404  * @g_dma_desc:         Enables gadget descriptor DMA (default: autodetect).
405  * @g_rx_fifo_size:	The periodic rx fifo size for the device, in
406  *			DWORDS from 16-32768 (default: 2048 if
407  *			possible, otherwise autodetect).
408  * @g_np_tx_fifo_size:	The non-periodic tx fifo size for the device in
409  *			DWORDS from 16-32768 (default: 1024 if
410  *			possible, otherwise autodetect).
411  * @g_tx_fifo_size:	An array of TX fifo sizes in dedicated fifo
412  *			mode. Each value corresponds to one EP
413  *			starting from EP1 (max 15 values). Sizes are
414  *			in DWORDS with possible values from
415  *			16-32768 (default: 256, 256, 256, 256, 768,
416  *			768, 768, 768, 0, 0, 0, 0, 0, 0, 0).
417  * @change_speed_quirk: Change speed configuration to DWC2_SPEED_PARAM_FULL
418  *                      while full&low speed device connect. And change speed
419  *                      back to DWC2_SPEED_PARAM_HIGH while device is gone.
420  *			0 - No (default)
421  *			1 - Yes
422  * @service_interval:   Enable service interval based scheduling.
423  *                      0 - No
424  *                      1 - Yes
425  *
426  * The following parameters may be specified when starting the module. These
427  * parameters define how the DWC_otg controller should be configured. A
428  * value of -1 (or any other out of range value) for any parameter means
429  * to read the value from hardware (if possible) or use the builtin
430  * default described above.
431  */
432 struct dwc2_core_params {
433 	struct usb_otg_caps otg_caps;
434 	u8 phy_type;
435 #define DWC2_PHY_TYPE_PARAM_FS		0
436 #define DWC2_PHY_TYPE_PARAM_UTMI	1
437 #define DWC2_PHY_TYPE_PARAM_ULPI	2
438 
439 	u8 speed;
440 #define DWC2_SPEED_PARAM_HIGH	0
441 #define DWC2_SPEED_PARAM_FULL	1
442 #define DWC2_SPEED_PARAM_LOW	2
443 
444 	u8 phy_utmi_width;
445 	bool phy_ulpi_ddr;
446 	bool phy_ulpi_ext_vbus;
447 	bool enable_dynamic_fifo;
448 	bool en_multiple_tx_fifo;
449 	bool i2c_enable;
450 	bool acg_enable;
451 	bool ulpi_fs_ls;
452 	bool ts_dline;
453 	bool reload_ctl;
454 	bool uframe_sched;
455 	bool external_id_pin_ctl;
456 
457 	int power_down;
458 #define DWC2_POWER_DOWN_PARAM_NONE		0
459 #define DWC2_POWER_DOWN_PARAM_PARTIAL		1
460 #define DWC2_POWER_DOWN_PARAM_HIBERNATION	2
461 	bool no_clock_gating;
462 
463 	bool lpm;
464 	bool lpm_clock_gating;
465 	bool besl;
466 	bool hird_threshold_en;
467 	bool service_interval;
468 	u8 hird_threshold;
469 	bool activate_stm_fs_transceiver;
470 	bool activate_stm_id_vb_detection;
471 	bool activate_ingenic_overcurrent_detection;
472 	bool ipg_isoc_en;
473 	u16 max_packet_count;
474 	u32 max_transfer_size;
475 	u32 ahbcfg;
476 
477 	/* GREFCLK parameters */
478 	u32 ref_clk_per;
479 	u16 sof_cnt_wkup_alert;
480 
481 	/* Host parameters */
482 	bool host_dma;
483 	bool dma_desc_enable;
484 	bool dma_desc_fs_enable;
485 	bool host_support_fs_ls_low_power;
486 	bool host_ls_low_power_phy_clk;
487 	bool oc_disable;
488 
489 	u8 host_channels;
490 	u16 host_rx_fifo_size;
491 	u16 host_nperio_tx_fifo_size;
492 	u16 host_perio_tx_fifo_size;
493 
494 	/* Gadget parameters */
495 	bool g_dma;
496 	bool g_dma_desc;
497 	u32 g_rx_fifo_size;
498 	u32 g_np_tx_fifo_size;
499 	u32 g_tx_fifo_size[MAX_EPS_CHANNELS];
500 
501 	bool change_speed_quirk;
502 };
503 
504 /**
505  * struct dwc2_hw_params - Autodetected parameters.
506  *
507  * These parameters are the various parameters read from hardware
508  * registers during initialization. They typically contain the best
509  * supported or maximum value that can be configured in the
510  * corresponding dwc2_core_params value.
511  *
512  * The values that are not in dwc2_core_params are documented below.
513  *
514  * @op_mode:             Mode of Operation
515  *                       0 - HNP- and SRP-Capable OTG (Host & Device)
516  *                       1 - SRP-Capable OTG (Host & Device)
517  *                       2 - Non-HNP and Non-SRP Capable OTG (Host & Device)
518  *                       3 - SRP-Capable Device
519  *                       4 - Non-OTG Device
520  *                       5 - SRP-Capable Host
521  *                       6 - Non-OTG Host
522  * @arch:                Architecture
523  *                       0 - Slave only
524  *                       1 - External DMA
525  *                       2 - Internal DMA
526  * @ipg_isoc_en:        This feature indicates that the controller supports
527  *                      the worst-case scenario of Rx followed by Rx
528  *                      Interpacket Gap (IPG) (32 bitTimes) as per the utmi
529  *                      specification for any token following ISOC OUT token.
530  *                       0 - Don't support
531  *                       1 - Support
532  * @power_optimized:    Are power optimizations enabled?
533  * @num_dev_ep:         Number of device endpoints available
534  * @num_dev_in_eps:     Number of device IN endpoints available
535  * @num_dev_perio_in_ep: Number of device periodic IN endpoints
536  *                       available
537  * @dev_token_q_depth:  Device Mode IN Token Sequence Learning Queue
538  *                      Depth
539  *                       0 to 30
540  * @host_perio_tx_q_depth:
541  *                      Host Mode Periodic Request Queue Depth
542  *                       2, 4 or 8
543  * @nperio_tx_q_depth:
544  *                      Non-Periodic Request Queue Depth
545  *                       2, 4 or 8
546  * @hs_phy_type:         High-speed PHY interface type
547  *                       0 - High-speed interface not supported
548  *                       1 - UTMI+
549  *                       2 - ULPI
550  *                       3 - UTMI+ and ULPI
551  * @fs_phy_type:         Full-speed PHY interface type
552  *                       0 - Full speed interface not supported
553  *                       1 - Dedicated full speed interface
554  *                       2 - FS pins shared with UTMI+ pins
555  *                       3 - FS pins shared with ULPI pins
556  * @total_fifo_size:    Total internal RAM for FIFOs (bytes)
557  * @hibernation:	Is hibernation enabled?
558  * @utmi_phy_data_width: UTMI+ PHY data width
559  *                       0 - 8 bits
560  *                       1 - 16 bits
561  *                       2 - 8 or 16 bits
562  * @snpsid:             Value from SNPSID register
563  * @dev_ep_dirs:        Direction of device endpoints (GHWCFG1)
564  * @g_tx_fifo_size:	Power-on values of TxFIFO sizes
565  * @dma_desc_enable:    When DMA mode is enabled, specifies whether to use
566  *                      address DMA mode or descriptor DMA mode for accessing
567  *                      the data FIFOs. The driver will automatically detect the
568  *                      value for this if none is specified.
569  *                       0 - Address DMA
570  *                       1 - Descriptor DMA (default, if available)
571  * @enable_dynamic_fifo: 0 - Use coreConsultant-specified FIFO size parameters
572  *                       1 - Allow dynamic FIFO sizing (default, if available)
573  * @en_multiple_tx_fifo: Specifies whether dedicated per-endpoint transmit FIFOs
574  *                      are enabled for non-periodic IN endpoints in device
575  *                      mode.
576  * @host_nperio_tx_fifo_size: Number of 4-byte words in the non-periodic Tx FIFO
577  *                      in host mode when dynamic FIFO sizing is enabled
578  *                       16 to 32768
579  *                      Actual maximum value is autodetected and also
580  *                      the default.
581  * @host_perio_tx_fifo_size: Number of 4-byte words in the periodic Tx FIFO in
582  *                      host mode when dynamic FIFO sizing is enabled
583  *                       16 to 32768
584  *                      Actual maximum value is autodetected and also
585  *                      the default.
586  * @max_transfer_size:  The maximum transfer size supported, in bytes
587  *                       2047 to 65,535
588  *                      Actual maximum value is autodetected and also
589  *                      the default.
590  * @max_packet_count:   The maximum number of packets in a transfer
591  *                       15 to 511
592  *                      Actual maximum value is autodetected and also
593  *                      the default.
594  * @host_channels:      The number of host channel registers to use
595  *                       1 to 16
596  *                      Actual maximum value is autodetected and also
597  *                      the default.
598  * @dev_nperio_tx_fifo_size: Number of 4-byte words in the non-periodic Tx FIFO
599  *			     in device mode when dynamic FIFO sizing is enabled
600  *			     16 to 32768
601  *			     Actual maximum value is autodetected and also
602  *			     the default.
603  * @i2c_enable:         Specifies whether to use the I2Cinterface for a full
604  *                      speed PHY. This parameter is only applicable if phy_type
605  *                      is FS.
606  *                       0 - No (default)
607  *                       1 - Yes
608  * @acg_enable:		For enabling Active Clock Gating in the controller
609  *                       0 - Disable
610  *                       1 - Enable
611  * @lpm_mode:		For enabling Link Power Management in the controller
612  *                       0 - Disable
613  *                       1 - Enable
614  * @rx_fifo_size:	Number of 4-byte words in the  Rx FIFO when dynamic
615  *			FIFO sizing is enabled 16 to 32768
616  *			Actual maximum value is autodetected and also
617  *			the default.
618  * @service_interval_mode: For enabling service interval based scheduling in the
619  *                         controller.
620  *                           0 - Disable
621  *                           1 - Enable
622  */
623 struct dwc2_hw_params {
624 	unsigned op_mode:3;
625 	unsigned arch:2;
626 	unsigned dma_desc_enable:1;
627 	unsigned enable_dynamic_fifo:1;
628 	unsigned en_multiple_tx_fifo:1;
629 	unsigned rx_fifo_size:16;
630 	unsigned host_nperio_tx_fifo_size:16;
631 	unsigned dev_nperio_tx_fifo_size:16;
632 	unsigned host_perio_tx_fifo_size:16;
633 	unsigned nperio_tx_q_depth:3;
634 	unsigned host_perio_tx_q_depth:3;
635 	unsigned dev_token_q_depth:5;
636 	unsigned max_transfer_size:26;
637 	unsigned max_packet_count:11;
638 	unsigned host_channels:5;
639 	unsigned hs_phy_type:2;
640 	unsigned fs_phy_type:2;
641 	unsigned i2c_enable:1;
642 	unsigned acg_enable:1;
643 	unsigned num_dev_ep:4;
644 	unsigned num_dev_in_eps : 4;
645 	unsigned num_dev_perio_in_ep:4;
646 	unsigned total_fifo_size:16;
647 	unsigned power_optimized:1;
648 	unsigned hibernation:1;
649 	unsigned utmi_phy_data_width:2;
650 	unsigned lpm_mode:1;
651 	unsigned ipg_isoc_en:1;
652 	unsigned service_interval_mode:1;
653 	u32 snpsid;
654 	u32 dev_ep_dirs;
655 	u32 g_tx_fifo_size[MAX_EPS_CHANNELS];
656 };
657 
658 /* Size of control and EP0 buffers */
659 #define DWC2_CTRL_BUFF_SIZE 8
660 
661 /**
662  * struct dwc2_gregs_backup - Holds global registers state before
663  * entering partial power down
664  * @gotgctl:		Backup of GOTGCTL register
665  * @gintmsk:		Backup of GINTMSK register
666  * @gahbcfg:		Backup of GAHBCFG register
667  * @gusbcfg:		Backup of GUSBCFG register
668  * @grxfsiz:		Backup of GRXFSIZ register
669  * @gnptxfsiz:		Backup of GNPTXFSIZ register
670  * @gi2cctl:		Backup of GI2CCTL register
671  * @glpmcfg:		Backup of GLPMCFG register
672  * @gdfifocfg:		Backup of GDFIFOCFG register
673  * @pcgcctl:		Backup of PCGCCTL register
674  * @pcgcctl1:		Backup of PCGCCTL1 register
675  * @dtxfsiz:		Backup of DTXFSIZ registers for each endpoint
676  * @gpwrdn:		Backup of GPWRDN register
677  * @valid:		True if registers values backuped.
678  */
679 struct dwc2_gregs_backup {
680 	u32 gotgctl;
681 	u32 gintmsk;
682 	u32 gahbcfg;
683 	u32 gusbcfg;
684 	u32 grxfsiz;
685 	u32 gnptxfsiz;
686 	u32 gi2cctl;
687 	u32 glpmcfg;
688 	u32 pcgcctl;
689 	u32 pcgcctl1;
690 	u32 gdfifocfg;
691 	u32 gpwrdn;
692 	bool valid;
693 };
694 
695 /**
696  * struct dwc2_dregs_backup - Holds device registers state before
697  * entering partial power down
698  * @dcfg:		Backup of DCFG register
699  * @dctl:		Backup of DCTL register
700  * @daintmsk:		Backup of DAINTMSK register
701  * @diepmsk:		Backup of DIEPMSK register
702  * @doepmsk:		Backup of DOEPMSK register
703  * @diepctl:		Backup of DIEPCTL register
704  * @dieptsiz:		Backup of DIEPTSIZ register
705  * @diepdma:		Backup of DIEPDMA register
706  * @doepctl:		Backup of DOEPCTL register
707  * @doeptsiz:		Backup of DOEPTSIZ register
708  * @doepdma:		Backup of DOEPDMA register
709  * @dtxfsiz:		Backup of DTXFSIZ registers for each endpoint
710  * @valid:      True if registers values backuped.
711  */
712 struct dwc2_dregs_backup {
713 	u32 dcfg;
714 	u32 dctl;
715 	u32 daintmsk;
716 	u32 diepmsk;
717 	u32 doepmsk;
718 	u32 diepctl[MAX_EPS_CHANNELS];
719 	u32 dieptsiz[MAX_EPS_CHANNELS];
720 	u32 diepdma[MAX_EPS_CHANNELS];
721 	u32 doepctl[MAX_EPS_CHANNELS];
722 	u32 doeptsiz[MAX_EPS_CHANNELS];
723 	u32 doepdma[MAX_EPS_CHANNELS];
724 	u32 dtxfsiz[MAX_EPS_CHANNELS];
725 	bool valid;
726 };
727 
728 /**
729  * struct dwc2_hregs_backup - Holds host registers state before
730  * entering partial power down
731  * @hcfg:		Backup of HCFG register
732  * @haintmsk:		Backup of HAINTMSK register
733  * @hcintmsk:		Backup of HCINTMSK register
734  * @hprt0:		Backup of HPTR0 register
735  * @hfir:		Backup of HFIR register
736  * @hptxfsiz:		Backup of HPTXFSIZ register
737  * @valid:      True if registers values backuped.
738  */
739 struct dwc2_hregs_backup {
740 	u32 hcfg;
741 	u32 haintmsk;
742 	u32 hcintmsk[MAX_EPS_CHANNELS];
743 	u32 hprt0;
744 	u32 hfir;
745 	u32 hptxfsiz;
746 	bool valid;
747 };
748 
749 /*
750  * Constants related to high speed periodic scheduling
751  *
752  * We have a periodic schedule that is DWC2_HS_SCHEDULE_UFRAMES long.  From a
753  * reservation point of view it's assumed that the schedule goes right back to
754  * the beginning after the end of the schedule.
755  *
756  * What does that mean for scheduling things with a long interval?  It means
757  * we'll reserve time for them in every possible microframe that they could
758  * ever be scheduled in.  ...but we'll still only actually schedule them as
759  * often as they were requested.
760  *
761  * We keep our schedule in a "bitmap" structure.  This simplifies having
762  * to keep track of and merge intervals: we just let the bitmap code do most
763  * of the heavy lifting.  In a way scheduling is much like memory allocation.
764  *
765  * We schedule 100us per uframe or 80% of 125us (the maximum amount you're
766  * supposed to schedule for periodic transfers).  That's according to spec.
767  *
768  * Note that though we only schedule 80% of each microframe, the bitmap that we
769  * keep the schedule in is tightly packed (AKA it doesn't have 100us worth of
770  * space for each uFrame).
771  *
772  * Requirements:
773  * - DWC2_HS_SCHEDULE_UFRAMES must even divide 0x4000 (HFNUM_MAX_FRNUM + 1)
774  * - DWC2_HS_SCHEDULE_UFRAMES must be 8 times DWC2_LS_SCHEDULE_FRAMES (probably
775  *   could be any multiple of 8 times DWC2_LS_SCHEDULE_FRAMES, but there might
776  *   be bugs).  The 8 comes from the USB spec: number of microframes per frame.
777  */
778 #define DWC2_US_PER_UFRAME		125
779 #define DWC2_HS_PERIODIC_US_PER_UFRAME	100
780 
781 #define DWC2_HS_SCHEDULE_UFRAMES	8
782 #define DWC2_HS_SCHEDULE_US		(DWC2_HS_SCHEDULE_UFRAMES * \
783 					 DWC2_HS_PERIODIC_US_PER_UFRAME)
784 
785 /*
786  * Constants related to low speed scheduling
787  *
788  * For high speed we schedule every 1us.  For low speed that's a bit overkill,
789  * so we make up a unit called a "slice" that's worth 25us.  There are 40
790  * slices in a full frame and we can schedule 36 of those (90%) for periodic
791  * transfers.
792  *
793  * Our low speed schedule can be as short as 1 frame or could be longer.  When
794  * we only schedule 1 frame it means that we'll need to reserve a time every
795  * frame even for things that only transfer very rarely, so something that runs
796  * every 2048 frames will get time reserved in every frame.  Our low speed
797  * schedule can be longer and we'll be able to handle more overlap, but that
798  * will come at increased memory cost and increased time to schedule.
799  *
800  * Note: one other advantage of a short low speed schedule is that if we mess
801  * up and miss scheduling we can jump in and use any of the slots that we
802  * happened to reserve.
803  *
804  * With 25 us per slice and 1 frame in the schedule, we only need 4 bytes for
805  * the schedule.  There will be one schedule per TT.
806  *
807  * Requirements:
808  * - DWC2_US_PER_SLICE must evenly divide DWC2_LS_PERIODIC_US_PER_FRAME.
809  */
810 #define DWC2_US_PER_SLICE	25
811 #define DWC2_SLICES_PER_UFRAME	(DWC2_US_PER_UFRAME / DWC2_US_PER_SLICE)
812 
813 #define DWC2_ROUND_US_TO_SLICE(us) \
814 				(DIV_ROUND_UP((us), DWC2_US_PER_SLICE) * \
815 				 DWC2_US_PER_SLICE)
816 
817 #define DWC2_LS_PERIODIC_US_PER_FRAME \
818 				900
819 #define DWC2_LS_PERIODIC_SLICES_PER_FRAME \
820 				(DWC2_LS_PERIODIC_US_PER_FRAME / \
821 				 DWC2_US_PER_SLICE)
822 
823 #define DWC2_LS_SCHEDULE_FRAMES	1
824 #define DWC2_LS_SCHEDULE_SLICES	(DWC2_LS_SCHEDULE_FRAMES * \
825 				 DWC2_LS_PERIODIC_SLICES_PER_FRAME)
826 
827 /**
828  * struct dwc2_hsotg - Holds the state of the driver, including the non-periodic
829  * and periodic schedules
830  *
831  * These are common for both host and peripheral modes:
832  *
833  * @dev:                The struct device pointer
834  * @regs:		Pointer to controller regs
835  * @hw_params:          Parameters that were autodetected from the
836  *                      hardware registers
837  * @params:	Parameters that define how the core should be configured
838  * @op_state:           The operational State, during transitions (a_host=>
839  *                      a_peripheral and b_device=>b_host) this may not match
840  *                      the core, but allows the software to determine
841  *                      transitions
842  * @dr_mode:            Requested mode of operation, one of following:
843  *                      - USB_DR_MODE_PERIPHERAL
844  *                      - USB_DR_MODE_HOST
845  *                      - USB_DR_MODE_OTG
846  * @role_sw:		usb_role_switch handle
847  * @role_sw_default_mode: default operation mode of controller while usb role
848  *			is USB_ROLE_NONE
849  * @hcd_enabled:	Host mode sub-driver initialization indicator.
850  * @gadget_enabled:	Peripheral mode sub-driver initialization indicator.
851  * @ll_hw_enabled:	Status of low-level hardware resources.
852  * @hibernated:		True if core is hibernated
853  * @in_ppd:		True if core is partial power down mode.
854  * @bus_suspended:	True if bus is suspended
855  * @reset_phy_on_wake:	Quirk saying that we should assert PHY reset on a
856  *			remote wakeup.
857  * @phy_off_for_suspend: Status of whether we turned the PHY off at suspend.
858  * @need_phy_for_wake:	Quirk saying that we should keep the PHY on at
859  *			suspend if we need USB to wake us up.
860  * @frame_number:       Frame number read from the core. For both device
861  *			and host modes. The value ranges are from 0
862  *			to HFNUM_MAX_FRNUM.
863  * @phy:                The otg phy transceiver structure for phy control.
864  * @uphy:               The otg phy transceiver structure for old USB phy
865  *                      control.
866  * @plat:               The platform specific configuration data. This can be
867  *                      removed once all SoCs support usb transceiver.
868  * @supplies:           Definition of USB power supplies
869  * @vbus_supply:        Regulator supplying vbus.
870  * @usb33d:		Optional 3.3v regulator used on some stm32 devices to
871  *			supply ID and VBUS detection hardware.
872  * @lock:		Spinlock that protects all the driver data structures
873  * @priv:		Stores a pointer to the struct usb_hcd
874  * @queuing_high_bandwidth: True if multiple packets of a high-bandwidth
875  *                      transfer are in process of being queued
876  * @srp_success:        Stores status of SRP request in the case of a FS PHY
877  *                      with an I2C interface
878  * @wq_otg:             Workqueue object used for handling of some interrupts
879  * @wf_otg:             Work object for handling Connector ID Status Change
880  *                      interrupt
881  * @wkp_timer:          Timer object for handling Wakeup Detected interrupt
882  * @lx_state:           Lx state of connected device
883  * @gr_backup: Backup of global registers during suspend
884  * @dr_backup: Backup of device registers during suspend
885  * @hr_backup: Backup of host registers during suspend
886  * @needs_byte_swap:		Specifies whether the opposite endianness.
887  *
888  * These are for host mode:
889  *
890  * @flags:              Flags for handling root port state changes
891  * @flags.d32:          Contain all root port flags
892  * @flags.b:            Separate root port flags from each other
893  * @flags.b.port_connect_status_change: True if root port connect status
894  *                      changed
895  * @flags.b.port_connect_status: True if device connected to root port
896  * @flags.b.port_reset_change: True if root port reset status changed
897  * @flags.b.port_enable_change: True if root port enable status changed
898  * @flags.b.port_suspend_change: True if root port suspend status changed
899  * @flags.b.port_over_current_change: True if root port over current state
900  *                       changed.
901  * @flags.b.port_l1_change: True if root port l1 status changed
902  * @flags.b.reserved:   Reserved bits of root port register
903  * @non_periodic_sched_inactive: Inactive QHs in the non-periodic schedule.
904  *                      Transfers associated with these QHs are not currently
905  *                      assigned to a host channel.
906  * @non_periodic_sched_active: Active QHs in the non-periodic schedule.
907  *                      Transfers associated with these QHs are currently
908  *                      assigned to a host channel.
909  * @non_periodic_qh_ptr: Pointer to next QH to process in the active
910  *                      non-periodic schedule
911  * @non_periodic_sched_waiting: Waiting QHs in the non-periodic schedule.
912  *                      Transfers associated with these QHs are not currently
913  *                      assigned to a host channel.
914  * @periodic_sched_inactive: Inactive QHs in the periodic schedule. This is a
915  *                      list of QHs for periodic transfers that are _not_
916  *                      scheduled for the next frame. Each QH in the list has an
917  *                      interval counter that determines when it needs to be
918  *                      scheduled for execution. This scheduling mechanism
919  *                      allows only a simple calculation for periodic bandwidth
920  *                      used (i.e. must assume that all periodic transfers may
921  *                      need to execute in the same frame). However, it greatly
922  *                      simplifies scheduling and should be sufficient for the
923  *                      vast majority of OTG hosts, which need to connect to a
924  *                      small number of peripherals at one time. Items move from
925  *                      this list to periodic_sched_ready when the QH interval
926  *                      counter is 0 at SOF.
927  * @periodic_sched_ready:  List of periodic QHs that are ready for execution in
928  *                      the next frame, but have not yet been assigned to host
929  *                      channels. Items move from this list to
930  *                      periodic_sched_assigned as host channels become
931  *                      available during the current frame.
932  * @periodic_sched_assigned: List of periodic QHs to be executed in the next
933  *                      frame that are assigned to host channels. Items move
934  *                      from this list to periodic_sched_queued as the
935  *                      transactions for the QH are queued to the DWC_otg
936  *                      controller.
937  * @periodic_sched_queued: List of periodic QHs that have been queued for
938  *                      execution. Items move from this list to either
939  *                      periodic_sched_inactive or periodic_sched_ready when the
940  *                      channel associated with the transfer is released. If the
941  *                      interval for the QH is 1, the item moves to
942  *                      periodic_sched_ready because it must be rescheduled for
943  *                      the next frame. Otherwise, the item moves to
944  *                      periodic_sched_inactive.
945  * @split_order:        List keeping track of channels doing splits, in order.
946  * @periodic_usecs:     Total bandwidth claimed so far for periodic transfers.
947  *                      This value is in microseconds per (micro)frame. The
948  *                      assumption is that all periodic transfers may occur in
949  *                      the same (micro)frame.
950  * @hs_periodic_bitmap: Bitmap used by the microframe scheduler any time the
951  *                      host is in high speed mode; low speed schedules are
952  *                      stored elsewhere since we need one per TT.
953  * @periodic_qh_count:  Count of periodic QHs, if using several eps. Used for
954  *                      SOF enable/disable.
955  * @free_hc_list:       Free host channels in the controller. This is a list of
956  *                      struct dwc2_host_chan items.
957  * @periodic_channels:  Number of host channels assigned to periodic transfers.
958  *                      Currently assuming that there is a dedicated host
959  *                      channel for each periodic transaction and at least one
960  *                      host channel is available for non-periodic transactions.
961  * @non_periodic_channels: Number of host channels assigned to non-periodic
962  *                      transfers
963  * @available_host_channels: Number of host channels available for the
964  *			     microframe scheduler to use
965  * @hc_ptr_array:       Array of pointers to the host channel descriptors.
966  *                      Allows accessing a host channel descriptor given the
967  *                      host channel number. This is useful in interrupt
968  *                      handlers.
969  * @status_buf:         Buffer used for data received during the status phase of
970  *                      a control transfer.
971  * @status_buf_dma:     DMA address for status_buf
972  * @start_work:         Delayed work for handling host A-cable connection
973  * @reset_work:         Delayed work for handling a port reset
974  * @phy_reset_work:     Work structure for doing a PHY reset
975  * @otg_port:           OTG port number
976  * @frame_list:         Frame list
977  * @frame_list_dma:     Frame list DMA address
978  * @frame_list_sz:      Frame list size
979  * @desc_gen_cache:     Kmem cache for generic descriptors
980  * @desc_hsisoc_cache:  Kmem cache for hs isochronous descriptors
981  * @unaligned_cache:    Kmem cache for DMA mode to handle non-aligned buf
982  *
983  * These are for peripheral mode:
984  *
985  * @driver:             USB gadget driver
986  * @dedicated_fifos:    Set if the hardware has dedicated IN-EP fifos.
987  * @num_of_eps:         Number of available EPs (excluding EP0)
988  * @debug_root:         Root directrory for debugfs.
989  * @ep0_reply:          Request used for ep0 reply.
990  * @ep0_buff:           Buffer for EP0 reply data, if needed.
991  * @ctrl_buff:          Buffer for EP0 control requests.
992  * @ctrl_req:           Request for EP0 control packets.
993  * @ep0_state:          EP0 control transfers state
994  * @delayed_status:		true when gadget driver asks for delayed status
995  * @test_mode:          USB test mode requested by the host
996  * @remote_wakeup_allowed: True if device is allowed to wake-up host by
997  *                      remote-wakeup signalling
998  * @setup_desc_dma:	EP0 setup stage desc chain DMA address
999  * @setup_desc:		EP0 setup stage desc chain pointer
1000  * @ctrl_in_desc_dma:	EP0 IN data phase desc chain DMA address
1001  * @ctrl_in_desc:	EP0 IN data phase desc chain pointer
1002  * @ctrl_out_desc_dma:	EP0 OUT data phase desc chain DMA address
1003  * @ctrl_out_desc:	EP0 OUT data phase desc chain pointer
1004  * @irq:		Interrupt request line number
1005  * @clk:		Pointer to otg clock
1006  * @utmi_clk:		Pointer to utmi_clk clock
1007  * @reset:		Pointer to dwc2 reset controller
1008  * @reset_ecc:          Pointer to dwc2 optional reset controller in Stratix10.
1009  * @regset:		A pointer to a struct debugfs_regset32, which contains
1010  *			a pointer to an array of register definitions, the
1011  *			array size and the base address where the register bank
1012  *			is to be found.
1013  * @last_frame_num:	Number of last frame. Range from 0 to  32768
1014  * @frame_num_array:    Used only  if CONFIG_USB_DWC2_TRACK_MISSED_SOFS is
1015  *			defined, for missed SOFs tracking. Array holds that
1016  *			frame numbers, which not equal to last_frame_num +1
1017  * @last_frame_num_array:   Used only  if CONFIG_USB_DWC2_TRACK_MISSED_SOFS is
1018  *			    defined, for missed SOFs tracking.
1019  *			    If current_frame_number != last_frame_num+1
1020  *			    then last_frame_num added to this array
1021  * @frame_num_idx:	Actual size of frame_num_array and last_frame_num_array
1022  * @dumped_frame_num_array:	1 - if missed SOFs frame numbers dumbed
1023  *				0 - if missed SOFs frame numbers not dumbed
1024  * @fifo_mem:			Total internal RAM for FIFOs (bytes)
1025  * @fifo_map:		Each bit intend for concrete fifo. If that bit is set,
1026  *			then that fifo is used
1027  * @gadget:		Represents a usb gadget device
1028  * @connected:		Used in slave mode. True if device connected with host
1029  * @eps_in:		The IN endpoints being supplied to the gadget framework
1030  * @eps_out:		The OUT endpoints being supplied to the gadget framework
1031  * @new_connection:	Used in host mode. True if there are new connected
1032  *			device
1033  * @enabled:		Indicates the enabling state of controller
1034  *
1035  */
1036 struct dwc2_hsotg {
1037 	struct device *dev;
1038 	void __iomem *regs;
1039 	/** Params detected from hardware */
1040 	struct dwc2_hw_params hw_params;
1041 	/** Params to actually use */
1042 	struct dwc2_core_params params;
1043 	enum usb_otg_state op_state;
1044 	enum usb_dr_mode dr_mode;
1045 	struct usb_role_switch *role_sw;
1046 	enum usb_dr_mode role_sw_default_mode;
1047 	unsigned int hcd_enabled:1;
1048 	unsigned int gadget_enabled:1;
1049 	unsigned int ll_hw_enabled:1;
1050 	unsigned int hibernated:1;
1051 	unsigned int in_ppd:1;
1052 	bool bus_suspended;
1053 	unsigned int reset_phy_on_wake:1;
1054 	unsigned int need_phy_for_wake:1;
1055 	unsigned int phy_off_for_suspend:1;
1056 	u16 frame_number;
1057 
1058 	struct phy *phy;
1059 	struct usb_phy *uphy;
1060 	struct dwc2_hsotg_plat *plat;
1061 	struct regulator_bulk_data supplies[DWC2_NUM_SUPPLIES];
1062 	struct regulator *vbus_supply;
1063 	struct regulator *usb33d;
1064 
1065 	spinlock_t lock;
1066 	void *priv;
1067 	int     irq;
1068 	struct clk *clk;
1069 	struct clk *utmi_clk;
1070 	struct reset_control *reset;
1071 	struct reset_control *reset_ecc;
1072 
1073 	unsigned int queuing_high_bandwidth:1;
1074 	unsigned int srp_success:1;
1075 
1076 	struct workqueue_struct *wq_otg;
1077 	struct work_struct wf_otg;
1078 	struct timer_list wkp_timer;
1079 	enum dwc2_lx_state lx_state;
1080 	struct dwc2_gregs_backup gr_backup;
1081 	struct dwc2_dregs_backup dr_backup;
1082 	struct dwc2_hregs_backup hr_backup;
1083 
1084 	struct dentry *debug_root;
1085 	struct debugfs_regset32 *regset;
1086 	bool needs_byte_swap;
1087 
1088 	/* DWC OTG HW Release versions */
1089 #define DWC2_CORE_REV_2_71a	0x4f54271a
1090 #define DWC2_CORE_REV_2_72a     0x4f54272a
1091 #define DWC2_CORE_REV_2_80a	0x4f54280a
1092 #define DWC2_CORE_REV_2_90a	0x4f54290a
1093 #define DWC2_CORE_REV_2_91a	0x4f54291a
1094 #define DWC2_CORE_REV_2_92a	0x4f54292a
1095 #define DWC2_CORE_REV_2_94a	0x4f54294a
1096 #define DWC2_CORE_REV_3_00a	0x4f54300a
1097 #define DWC2_CORE_REV_3_10a	0x4f54310a
1098 #define DWC2_CORE_REV_4_00a	0x4f54400a
1099 #define DWC2_CORE_REV_4_20a	0x4f54420a
1100 #define DWC2_FS_IOT_REV_1_00a	0x5531100a
1101 #define DWC2_HS_IOT_REV_1_00a	0x5532100a
1102 #define DWC2_CORE_REV_MASK	0x0000ffff
1103 
1104 	/* DWC OTG HW Core ID */
1105 #define DWC2_OTG_ID		0x4f540000
1106 #define DWC2_FS_IOT_ID		0x55310000
1107 #define DWC2_HS_IOT_ID		0x55320000
1108 
1109 #if IS_ENABLED(CONFIG_USB_DWC2_HOST) || IS_ENABLED(CONFIG_USB_DWC2_DUAL_ROLE)
1110 	union dwc2_hcd_internal_flags {
1111 		u32 d32;
1112 		struct {
1113 			unsigned port_connect_status_change:1;
1114 			unsigned port_connect_status:1;
1115 			unsigned port_reset_change:1;
1116 			unsigned port_enable_change:1;
1117 			unsigned port_suspend_change:1;
1118 			unsigned port_over_current_change:1;
1119 			unsigned port_l1_change:1;
1120 			unsigned reserved:25;
1121 		} b;
1122 	} flags;
1123 
1124 	struct list_head non_periodic_sched_inactive;
1125 	struct list_head non_periodic_sched_waiting;
1126 	struct list_head non_periodic_sched_active;
1127 	struct list_head *non_periodic_qh_ptr;
1128 	struct list_head periodic_sched_inactive;
1129 	struct list_head periodic_sched_ready;
1130 	struct list_head periodic_sched_assigned;
1131 	struct list_head periodic_sched_queued;
1132 	struct list_head split_order;
1133 	u16 periodic_usecs;
1134 	DECLARE_BITMAP(hs_periodic_bitmap, DWC2_HS_SCHEDULE_US);
1135 	u16 periodic_qh_count;
1136 	bool new_connection;
1137 
1138 	u16 last_frame_num;
1139 
1140 #ifdef CONFIG_USB_DWC2_TRACK_MISSED_SOFS
1141 #define FRAME_NUM_ARRAY_SIZE 1000
1142 	u16 *frame_num_array;
1143 	u16 *last_frame_num_array;
1144 	int frame_num_idx;
1145 	int dumped_frame_num_array;
1146 #endif
1147 
1148 	struct list_head free_hc_list;
1149 	int periodic_channels;
1150 	int non_periodic_channels;
1151 	int available_host_channels;
1152 	struct dwc2_host_chan *hc_ptr_array[MAX_EPS_CHANNELS];
1153 	u8 *status_buf;
1154 	dma_addr_t status_buf_dma;
1155 #define DWC2_HCD_STATUS_BUF_SIZE 64
1156 
1157 	struct delayed_work start_work;
1158 	struct delayed_work reset_work;
1159 	struct work_struct phy_reset_work;
1160 	u8 otg_port;
1161 	u32 *frame_list;
1162 	dma_addr_t frame_list_dma;
1163 	u32 frame_list_sz;
1164 	struct kmem_cache *desc_gen_cache;
1165 	struct kmem_cache *desc_hsisoc_cache;
1166 	struct kmem_cache *unaligned_cache;
1167 #define DWC2_KMEM_UNALIGNED_BUF_SIZE 1024
1168 
1169 #endif /* CONFIG_USB_DWC2_HOST || CONFIG_USB_DWC2_DUAL_ROLE */
1170 
1171 #if IS_ENABLED(CONFIG_USB_DWC2_PERIPHERAL) || \
1172 	IS_ENABLED(CONFIG_USB_DWC2_DUAL_ROLE)
1173 	/* Gadget structures */
1174 	struct usb_gadget_driver *driver;
1175 	int fifo_mem;
1176 	unsigned int dedicated_fifos:1;
1177 	unsigned char num_of_eps;
1178 	u32 fifo_map;
1179 
1180 	struct usb_request *ep0_reply;
1181 	struct usb_request *ctrl_req;
1182 	void *ep0_buff;
1183 	void *ctrl_buff;
1184 	enum dwc2_ep0_state ep0_state;
1185 	unsigned delayed_status : 1;
1186 	u8 test_mode;
1187 
1188 	dma_addr_t setup_desc_dma[2];
1189 	struct dwc2_dma_desc *setup_desc[2];
1190 	dma_addr_t ctrl_in_desc_dma;
1191 	struct dwc2_dma_desc *ctrl_in_desc;
1192 	dma_addr_t ctrl_out_desc_dma;
1193 	struct dwc2_dma_desc *ctrl_out_desc;
1194 
1195 	struct usb_gadget gadget;
1196 	unsigned int enabled:1;
1197 	unsigned int connected:1;
1198 	unsigned int remote_wakeup_allowed:1;
1199 	struct dwc2_hsotg_ep *eps_in[MAX_EPS_CHANNELS];
1200 	struct dwc2_hsotg_ep *eps_out[MAX_EPS_CHANNELS];
1201 #endif /* CONFIG_USB_DWC2_PERIPHERAL || CONFIG_USB_DWC2_DUAL_ROLE */
1202 };
1203 
1204 /* Normal architectures just use readl/write */
dwc2_readl(struct dwc2_hsotg * hsotg,u32 offset)1205 static inline u32 dwc2_readl(struct dwc2_hsotg *hsotg, u32 offset)
1206 {
1207 	u32 val;
1208 
1209 	val = readl(hsotg->regs + offset);
1210 	if (hsotg->needs_byte_swap)
1211 		return swab32(val);
1212 	else
1213 		return val;
1214 }
1215 
dwc2_writel(struct dwc2_hsotg * hsotg,u32 value,u32 offset)1216 static inline void dwc2_writel(struct dwc2_hsotg *hsotg, u32 value, u32 offset)
1217 {
1218 	if (hsotg->needs_byte_swap)
1219 		writel(swab32(value), hsotg->regs + offset);
1220 	else
1221 		writel(value, hsotg->regs + offset);
1222 
1223 #ifdef DWC2_LOG_WRITES
1224 	pr_info("info:: wrote %08x to %p\n", value, hsotg->regs + offset);
1225 #endif
1226 }
1227 
dwc2_readl_rep(struct dwc2_hsotg * hsotg,u32 offset,void * buffer,unsigned int count)1228 static inline void dwc2_readl_rep(struct dwc2_hsotg *hsotg, u32 offset,
1229 				  void *buffer, unsigned int count)
1230 {
1231 	if (count) {
1232 		u32 *buf = buffer;
1233 
1234 		do {
1235 			u32 x = dwc2_readl(hsotg, offset);
1236 			*buf++ = x;
1237 		} while (--count);
1238 	}
1239 }
1240 
dwc2_writel_rep(struct dwc2_hsotg * hsotg,u32 offset,const void * buffer,unsigned int count)1241 static inline void dwc2_writel_rep(struct dwc2_hsotg *hsotg, u32 offset,
1242 				   const void *buffer, unsigned int count)
1243 {
1244 	if (count) {
1245 		const u32 *buf = buffer;
1246 
1247 		do {
1248 			dwc2_writel(hsotg, *buf++, offset);
1249 		} while (--count);
1250 	}
1251 }
1252 
1253 /* Reasons for halting a host channel */
1254 enum dwc2_halt_status {
1255 	DWC2_HC_XFER_NO_HALT_STATUS,
1256 	DWC2_HC_XFER_COMPLETE,
1257 	DWC2_HC_XFER_URB_COMPLETE,
1258 	DWC2_HC_XFER_ACK,
1259 	DWC2_HC_XFER_NAK,
1260 	DWC2_HC_XFER_NYET,
1261 	DWC2_HC_XFER_STALL,
1262 	DWC2_HC_XFER_XACT_ERR,
1263 	DWC2_HC_XFER_FRAME_OVERRUN,
1264 	DWC2_HC_XFER_BABBLE_ERR,
1265 	DWC2_HC_XFER_DATA_TOGGLE_ERR,
1266 	DWC2_HC_XFER_AHB_ERR,
1267 	DWC2_HC_XFER_PERIODIC_INCOMPLETE,
1268 	DWC2_HC_XFER_URB_DEQUEUE,
1269 };
1270 
1271 /* Core version information */
dwc2_is_iot(struct dwc2_hsotg * hsotg)1272 static inline bool dwc2_is_iot(struct dwc2_hsotg *hsotg)
1273 {
1274 	return (hsotg->hw_params.snpsid & 0xfff00000) == 0x55300000;
1275 }
1276 
dwc2_is_fs_iot(struct dwc2_hsotg * hsotg)1277 static inline bool dwc2_is_fs_iot(struct dwc2_hsotg *hsotg)
1278 {
1279 	return (hsotg->hw_params.snpsid & 0xffff0000) == 0x55310000;
1280 }
1281 
dwc2_is_hs_iot(struct dwc2_hsotg * hsotg)1282 static inline bool dwc2_is_hs_iot(struct dwc2_hsotg *hsotg)
1283 {
1284 	return (hsotg->hw_params.snpsid & 0xffff0000) == 0x55320000;
1285 }
1286 
1287 /*
1288  * The following functions support initialization of the core driver component
1289  * and the DWC_otg controller
1290  */
1291 int dwc2_core_reset(struct dwc2_hsotg *hsotg, bool skip_wait);
1292 int dwc2_enter_partial_power_down(struct dwc2_hsotg *hsotg);
1293 int dwc2_exit_partial_power_down(struct dwc2_hsotg *hsotg, int rem_wakeup,
1294 				 bool restore);
1295 int dwc2_enter_hibernation(struct dwc2_hsotg *hsotg, int is_host);
1296 int dwc2_exit_hibernation(struct dwc2_hsotg *hsotg, int rem_wakeup,
1297 		int reset, int is_host);
1298 void dwc2_init_fs_ls_pclk_sel(struct dwc2_hsotg *hsotg);
1299 int dwc2_phy_init(struct dwc2_hsotg *hsotg, bool select_phy);
1300 
1301 void dwc2_force_mode(struct dwc2_hsotg *hsotg, bool host);
1302 void dwc2_force_dr_mode(struct dwc2_hsotg *hsotg);
1303 
1304 bool dwc2_is_controller_alive(struct dwc2_hsotg *hsotg);
1305 
1306 int dwc2_check_core_version(struct dwc2_hsotg *hsotg);
1307 
1308 /*
1309  * Common core Functions.
1310  * The following functions support managing the DWC_otg controller in either
1311  * device or host mode.
1312  */
1313 void dwc2_read_packet(struct dwc2_hsotg *hsotg, u8 *dest, u16 bytes);
1314 void dwc2_flush_tx_fifo(struct dwc2_hsotg *hsotg, const int num);
1315 void dwc2_flush_rx_fifo(struct dwc2_hsotg *hsotg);
1316 
1317 void dwc2_enable_global_interrupts(struct dwc2_hsotg *hcd);
1318 void dwc2_disable_global_interrupts(struct dwc2_hsotg *hcd);
1319 
1320 void dwc2_hib_restore_common(struct dwc2_hsotg *hsotg, int rem_wakeup,
1321 			     int is_host);
1322 int dwc2_backup_global_registers(struct dwc2_hsotg *hsotg);
1323 int dwc2_restore_global_registers(struct dwc2_hsotg *hsotg);
1324 
1325 void dwc2_enable_acg(struct dwc2_hsotg *hsotg);
1326 
1327 /* This function should be called on every hardware interrupt. */
1328 irqreturn_t dwc2_handle_common_intr(int irq, void *dev);
1329 
1330 /* The device ID match table */
1331 extern const struct of_device_id dwc2_of_match_table[];
1332 extern const struct acpi_device_id dwc2_acpi_match[];
1333 extern const struct pci_device_id dwc2_pci_ids[];
1334 
1335 int dwc2_lowlevel_hw_enable(struct dwc2_hsotg *hsotg);
1336 int dwc2_lowlevel_hw_disable(struct dwc2_hsotg *hsotg);
1337 
1338 /* Common polling functions */
1339 int dwc2_hsotg_wait_bit_set(struct dwc2_hsotg *hs_otg, u32 reg, u32 bit,
1340 			    u32 timeout);
1341 int dwc2_hsotg_wait_bit_clear(struct dwc2_hsotg *hs_otg, u32 reg, u32 bit,
1342 			      u32 timeout);
1343 /* Parameters */
1344 int dwc2_get_hwparams(struct dwc2_hsotg *hsotg);
1345 int dwc2_init_params(struct dwc2_hsotg *hsotg);
1346 
1347 /*
1348  * The following functions check the controller's OTG operation mode
1349  * capability (GHWCFG2.OTG_MODE).
1350  *
1351  * These functions can be used before the internal hsotg->hw_params
1352  * are read in and cached so they always read directly from the
1353  * GHWCFG2 register.
1354  */
1355 unsigned int dwc2_op_mode(struct dwc2_hsotg *hsotg);
1356 bool dwc2_hw_is_otg(struct dwc2_hsotg *hsotg);
1357 bool dwc2_hw_is_host(struct dwc2_hsotg *hsotg);
1358 bool dwc2_hw_is_device(struct dwc2_hsotg *hsotg);
1359 
1360 /*
1361  * Returns the mode of operation, host or device
1362  */
dwc2_is_host_mode(struct dwc2_hsotg * hsotg)1363 static inline int dwc2_is_host_mode(struct dwc2_hsotg *hsotg)
1364 {
1365 	return (dwc2_readl(hsotg, GINTSTS) & GINTSTS_CURMODE_HOST) != 0;
1366 }
1367 
dwc2_is_device_mode(struct dwc2_hsotg * hsotg)1368 static inline int dwc2_is_device_mode(struct dwc2_hsotg *hsotg)
1369 {
1370 	return (dwc2_readl(hsotg, GINTSTS) & GINTSTS_CURMODE_HOST) == 0;
1371 }
1372 
1373 int dwc2_drd_init(struct dwc2_hsotg *hsotg);
1374 void dwc2_drd_suspend(struct dwc2_hsotg *hsotg);
1375 void dwc2_drd_resume(struct dwc2_hsotg *hsotg);
1376 void dwc2_drd_exit(struct dwc2_hsotg *hsotg);
1377 
1378 /*
1379  * Dump core registers and SPRAM
1380  */
1381 void dwc2_dump_dev_registers(struct dwc2_hsotg *hsotg);
1382 void dwc2_dump_host_registers(struct dwc2_hsotg *hsotg);
1383 void dwc2_dump_global_registers(struct dwc2_hsotg *hsotg);
1384 
1385 /* Gadget defines */
1386 #if IS_ENABLED(CONFIG_USB_DWC2_PERIPHERAL) || \
1387 	IS_ENABLED(CONFIG_USB_DWC2_DUAL_ROLE)
1388 int dwc2_hsotg_remove(struct dwc2_hsotg *hsotg);
1389 int dwc2_hsotg_suspend(struct dwc2_hsotg *dwc2);
1390 int dwc2_hsotg_resume(struct dwc2_hsotg *dwc2);
1391 int dwc2_gadget_init(struct dwc2_hsotg *hsotg);
1392 void dwc2_hsotg_core_init_disconnected(struct dwc2_hsotg *dwc2,
1393 				       bool reset);
1394 void dwc2_hsotg_core_disconnect(struct dwc2_hsotg *hsotg);
1395 void dwc2_hsotg_core_connect(struct dwc2_hsotg *hsotg);
1396 void dwc2_hsotg_disconnect(struct dwc2_hsotg *dwc2);
1397 int dwc2_hsotg_set_test_mode(struct dwc2_hsotg *hsotg, int testmode);
1398 #define dwc2_is_device_connected(hsotg) (hsotg->connected)
1399 #define dwc2_is_device_enabled(hsotg) (hsotg->enabled)
1400 int dwc2_backup_device_registers(struct dwc2_hsotg *hsotg);
1401 int dwc2_restore_device_registers(struct dwc2_hsotg *hsotg, int remote_wakeup);
1402 int dwc2_gadget_enter_hibernation(struct dwc2_hsotg *hsotg);
1403 int dwc2_gadget_exit_hibernation(struct dwc2_hsotg *hsotg,
1404 				 int rem_wakeup, int reset);
1405 int dwc2_gadget_enter_partial_power_down(struct dwc2_hsotg *hsotg);
1406 int dwc2_gadget_exit_partial_power_down(struct dwc2_hsotg *hsotg,
1407 					bool restore);
1408 void dwc2_gadget_enter_clock_gating(struct dwc2_hsotg *hsotg);
1409 void dwc2_gadget_exit_clock_gating(struct dwc2_hsotg *hsotg,
1410 				   int rem_wakeup);
1411 int dwc2_hsotg_tx_fifo_count(struct dwc2_hsotg *hsotg);
1412 int dwc2_hsotg_tx_fifo_total_depth(struct dwc2_hsotg *hsotg);
1413 int dwc2_hsotg_tx_fifo_average_depth(struct dwc2_hsotg *hsotg);
1414 void dwc2_gadget_init_lpm(struct dwc2_hsotg *hsotg);
1415 void dwc2_gadget_program_ref_clk(struct dwc2_hsotg *hsotg);
dwc2_clear_fifo_map(struct dwc2_hsotg * hsotg)1416 static inline void dwc2_clear_fifo_map(struct dwc2_hsotg *hsotg)
1417 { hsotg->fifo_map = 0; }
1418 #else
dwc2_hsotg_remove(struct dwc2_hsotg * dwc2)1419 static inline int dwc2_hsotg_remove(struct dwc2_hsotg *dwc2)
1420 { return 0; }
dwc2_hsotg_suspend(struct dwc2_hsotg * dwc2)1421 static inline int dwc2_hsotg_suspend(struct dwc2_hsotg *dwc2)
1422 { return 0; }
dwc2_hsotg_resume(struct dwc2_hsotg * dwc2)1423 static inline int dwc2_hsotg_resume(struct dwc2_hsotg *dwc2)
1424 { return 0; }
dwc2_gadget_init(struct dwc2_hsotg * hsotg)1425 static inline int dwc2_gadget_init(struct dwc2_hsotg *hsotg)
1426 { return 0; }
dwc2_hsotg_core_init_disconnected(struct dwc2_hsotg * dwc2,bool reset)1427 static inline void dwc2_hsotg_core_init_disconnected(struct dwc2_hsotg *dwc2,
1428 						     bool reset) {}
dwc2_hsotg_core_disconnect(struct dwc2_hsotg * hsotg)1429 static inline void dwc2_hsotg_core_disconnect(struct dwc2_hsotg *hsotg) {}
dwc2_hsotg_core_connect(struct dwc2_hsotg * hsotg)1430 static inline void dwc2_hsotg_core_connect(struct dwc2_hsotg *hsotg) {}
dwc2_hsotg_disconnect(struct dwc2_hsotg * dwc2)1431 static inline void dwc2_hsotg_disconnect(struct dwc2_hsotg *dwc2) {}
dwc2_hsotg_set_test_mode(struct dwc2_hsotg * hsotg,int testmode)1432 static inline int dwc2_hsotg_set_test_mode(struct dwc2_hsotg *hsotg,
1433 					   int testmode)
1434 { return 0; }
1435 #define dwc2_is_device_connected(hsotg) (0)
1436 #define dwc2_is_device_enabled(hsotg) (0)
dwc2_backup_device_registers(struct dwc2_hsotg * hsotg)1437 static inline int dwc2_backup_device_registers(struct dwc2_hsotg *hsotg)
1438 { return 0; }
dwc2_restore_device_registers(struct dwc2_hsotg * hsotg,int remote_wakeup)1439 static inline int dwc2_restore_device_registers(struct dwc2_hsotg *hsotg,
1440 						int remote_wakeup)
1441 { return 0; }
dwc2_gadget_enter_hibernation(struct dwc2_hsotg * hsotg)1442 static inline int dwc2_gadget_enter_hibernation(struct dwc2_hsotg *hsotg)
1443 { return 0; }
dwc2_gadget_exit_hibernation(struct dwc2_hsotg * hsotg,int rem_wakeup,int reset)1444 static inline int dwc2_gadget_exit_hibernation(struct dwc2_hsotg *hsotg,
1445 					       int rem_wakeup, int reset)
1446 { return 0; }
dwc2_gadget_enter_partial_power_down(struct dwc2_hsotg * hsotg)1447 static inline int dwc2_gadget_enter_partial_power_down(struct dwc2_hsotg *hsotg)
1448 { return 0; }
dwc2_gadget_exit_partial_power_down(struct dwc2_hsotg * hsotg,bool restore)1449 static inline int dwc2_gadget_exit_partial_power_down(struct dwc2_hsotg *hsotg,
1450 						      bool restore)
1451 { return 0; }
dwc2_gadget_enter_clock_gating(struct dwc2_hsotg * hsotg)1452 static inline void dwc2_gadget_enter_clock_gating(struct dwc2_hsotg *hsotg) {}
dwc2_gadget_exit_clock_gating(struct dwc2_hsotg * hsotg,int rem_wakeup)1453 static inline void dwc2_gadget_exit_clock_gating(struct dwc2_hsotg *hsotg,
1454 						 int rem_wakeup) {}
dwc2_hsotg_tx_fifo_count(struct dwc2_hsotg * hsotg)1455 static inline int dwc2_hsotg_tx_fifo_count(struct dwc2_hsotg *hsotg)
1456 { return 0; }
dwc2_hsotg_tx_fifo_total_depth(struct dwc2_hsotg * hsotg)1457 static inline int dwc2_hsotg_tx_fifo_total_depth(struct dwc2_hsotg *hsotg)
1458 { return 0; }
dwc2_hsotg_tx_fifo_average_depth(struct dwc2_hsotg * hsotg)1459 static inline int dwc2_hsotg_tx_fifo_average_depth(struct dwc2_hsotg *hsotg)
1460 { return 0; }
dwc2_gadget_init_lpm(struct dwc2_hsotg * hsotg)1461 static inline void dwc2_gadget_init_lpm(struct dwc2_hsotg *hsotg) {}
dwc2_gadget_program_ref_clk(struct dwc2_hsotg * hsotg)1462 static inline void dwc2_gadget_program_ref_clk(struct dwc2_hsotg *hsotg) {}
dwc2_clear_fifo_map(struct dwc2_hsotg * hsotg)1463 static inline void dwc2_clear_fifo_map(struct dwc2_hsotg *hsotg) {}
1464 #endif
1465 
1466 #if IS_ENABLED(CONFIG_USB_DWC2_HOST) || IS_ENABLED(CONFIG_USB_DWC2_DUAL_ROLE)
1467 int dwc2_hcd_get_frame_number(struct dwc2_hsotg *hsotg);
1468 int dwc2_hcd_get_future_frame_number(struct dwc2_hsotg *hsotg, int us);
1469 void dwc2_hcd_connect(struct dwc2_hsotg *hsotg);
1470 void dwc2_hcd_disconnect(struct dwc2_hsotg *hsotg, bool force);
1471 void dwc2_hcd_start(struct dwc2_hsotg *hsotg);
1472 int dwc2_core_init(struct dwc2_hsotg *hsotg, bool initial_setup);
1473 int dwc2_port_suspend(struct dwc2_hsotg *hsotg, u16 windex);
1474 int dwc2_port_resume(struct dwc2_hsotg *hsotg);
1475 int dwc2_backup_host_registers(struct dwc2_hsotg *hsotg);
1476 int dwc2_restore_host_registers(struct dwc2_hsotg *hsotg);
1477 int dwc2_host_enter_hibernation(struct dwc2_hsotg *hsotg);
1478 int dwc2_host_exit_hibernation(struct dwc2_hsotg *hsotg,
1479 			       int rem_wakeup, int reset);
1480 int dwc2_host_enter_partial_power_down(struct dwc2_hsotg *hsotg);
1481 int dwc2_host_exit_partial_power_down(struct dwc2_hsotg *hsotg,
1482 				      int rem_wakeup, bool restore);
1483 void dwc2_host_enter_clock_gating(struct dwc2_hsotg *hsotg);
1484 void dwc2_host_exit_clock_gating(struct dwc2_hsotg *hsotg, int rem_wakeup);
1485 bool dwc2_host_can_poweroff_phy(struct dwc2_hsotg *dwc2);
dwc2_host_schedule_phy_reset(struct dwc2_hsotg * hsotg)1486 static inline void dwc2_host_schedule_phy_reset(struct dwc2_hsotg *hsotg)
1487 { schedule_work(&hsotg->phy_reset_work); }
1488 #else
dwc2_hcd_get_frame_number(struct dwc2_hsotg * hsotg)1489 static inline int dwc2_hcd_get_frame_number(struct dwc2_hsotg *hsotg)
1490 { return 0; }
dwc2_hcd_get_future_frame_number(struct dwc2_hsotg * hsotg,int us)1491 static inline int dwc2_hcd_get_future_frame_number(struct dwc2_hsotg *hsotg,
1492 						   int us)
1493 { return 0; }
dwc2_hcd_connect(struct dwc2_hsotg * hsotg)1494 static inline void dwc2_hcd_connect(struct dwc2_hsotg *hsotg) {}
dwc2_hcd_disconnect(struct dwc2_hsotg * hsotg,bool force)1495 static inline void dwc2_hcd_disconnect(struct dwc2_hsotg *hsotg, bool force) {}
dwc2_hcd_start(struct dwc2_hsotg * hsotg)1496 static inline void dwc2_hcd_start(struct dwc2_hsotg *hsotg) {}
dwc2_hcd_remove(struct dwc2_hsotg * hsotg)1497 static inline void dwc2_hcd_remove(struct dwc2_hsotg *hsotg) {}
dwc2_core_init(struct dwc2_hsotg * hsotg,bool initial_setup)1498 static inline int dwc2_core_init(struct dwc2_hsotg *hsotg, bool initial_setup)
1499 { return 0; }
dwc2_port_suspend(struct dwc2_hsotg * hsotg,u16 windex)1500 static inline int dwc2_port_suspend(struct dwc2_hsotg *hsotg, u16 windex)
1501 { return 0; }
dwc2_port_resume(struct dwc2_hsotg * hsotg)1502 static inline int dwc2_port_resume(struct dwc2_hsotg *hsotg)
1503 { return 0; }
dwc2_hcd_init(struct dwc2_hsotg * hsotg)1504 static inline int dwc2_hcd_init(struct dwc2_hsotg *hsotg)
1505 { return 0; }
dwc2_backup_host_registers(struct dwc2_hsotg * hsotg)1506 static inline int dwc2_backup_host_registers(struct dwc2_hsotg *hsotg)
1507 { return 0; }
dwc2_restore_host_registers(struct dwc2_hsotg * hsotg)1508 static inline int dwc2_restore_host_registers(struct dwc2_hsotg *hsotg)
1509 { return 0; }
dwc2_host_enter_hibernation(struct dwc2_hsotg * hsotg)1510 static inline int dwc2_host_enter_hibernation(struct dwc2_hsotg *hsotg)
1511 { return 0; }
dwc2_host_exit_hibernation(struct dwc2_hsotg * hsotg,int rem_wakeup,int reset)1512 static inline int dwc2_host_exit_hibernation(struct dwc2_hsotg *hsotg,
1513 					     int rem_wakeup, int reset)
1514 { return 0; }
dwc2_host_enter_partial_power_down(struct dwc2_hsotg * hsotg)1515 static inline int dwc2_host_enter_partial_power_down(struct dwc2_hsotg *hsotg)
1516 { return 0; }
dwc2_host_exit_partial_power_down(struct dwc2_hsotg * hsotg,int rem_wakeup,bool restore)1517 static inline int dwc2_host_exit_partial_power_down(struct dwc2_hsotg *hsotg,
1518 						    int rem_wakeup, bool restore)
1519 { return 0; }
dwc2_host_enter_clock_gating(struct dwc2_hsotg * hsotg)1520 static inline void dwc2_host_enter_clock_gating(struct dwc2_hsotg *hsotg) {}
dwc2_host_exit_clock_gating(struct dwc2_hsotg * hsotg,int rem_wakeup)1521 static inline void dwc2_host_exit_clock_gating(struct dwc2_hsotg *hsotg,
1522 					       int rem_wakeup) {}
dwc2_host_can_poweroff_phy(struct dwc2_hsotg * dwc2)1523 static inline bool dwc2_host_can_poweroff_phy(struct dwc2_hsotg *dwc2)
1524 { return false; }
dwc2_host_schedule_phy_reset(struct dwc2_hsotg * hsotg)1525 static inline void dwc2_host_schedule_phy_reset(struct dwc2_hsotg *hsotg) {}
1526 
1527 #endif
1528 
1529 #endif /* __DWC2_CORE_H__ */
1530