1 /*****************************************************************************
2 * Copyright 2003 - 2008 Broadcom Corporation. All rights reserved.
3 *
4 * Unless you and Broadcom execute a separate written software license
5 * agreement governing use of this software, this software is licensed to you
6 * under the terms of the GNU General Public License version 2, available at
7 * http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
8 *
9 * Notwithstanding the above, under no circumstances may you combine this
10 * software in any way with any other Broadcom software provided under a
11 * license other than the GPL, without Broadcom's express prior written
12 * consent.
13 *****************************************************************************/
14
15 /****************************************************************************/
16 /**
17 * @file chipcHw_init.c
18 *
19 * @brief Low level CHIPC PLL configuration functions
20 *
21 * @note
22 *
23 * These routines provide basic PLL controlling functionality only.
24 */
25 /****************************************************************************/
26
27 /* ---- Include Files ---------------------------------------------------- */
28
29 #include <csp/errno.h>
30 #include <csp/stdint.h>
31 #include <csp/module.h>
32
33 #include <mach/csp/chipcHw_def.h>
34 #include <mach/csp/chipcHw_inline.h>
35
36 #include <csp/reg.h>
37 #include <csp/delay.h>
38 /* ---- Private Constants and Types --------------------------------------- */
39
40 /*
41 Calculation for NDIV_i to obtain VCO frequency
42 -----------------------------------------------
43
44 Freq_vco = Freq_ref * (P2 / P1) * (PLL_NDIV_i + PLL_NDIV_f)
45 for Freq_vco = VCO_FREQ_MHz
46 Freq_ref = chipcHw_XTAL_FREQ_Hz
47 PLL_P1 = PLL_P2 = 1
48 and
49 PLL_NDIV_f = 0
50
51 We get:
52 PLL_NDIV_i = Freq_vco / Freq_ref = VCO_FREQ_MHz / chipcHw_XTAL_FREQ_Hz
53
54 Calculation for PLL MDIV to obtain frequency Freq_x for channel x
55 -----------------------------------------------------------------
56 Freq_x = chipcHw_XTAL_FREQ_Hz * PLL_NDIV_i / PLL_MDIV_x = VCO_FREQ_MHz / PLL_MDIV_x
57
58 PLL_MDIV_x = VCO_FREQ_MHz / Freq_x
59 */
60
61 /* ---- Private Variables ------------------------------------------------- */
62 /****************************************************************************/
63 /**
64 * @brief Initializes the PLL2
65 *
66 * This function initializes the PLL2
67 *
68 */
69 /****************************************************************************/
chipcHw_pll2Enable(uint32_t vcoFreqHz)70 void chipcHw_pll2Enable(uint32_t vcoFreqHz)
71 {
72 uint32_t pllPreDivider2 = 0;
73
74 {
75 REG_LOCAL_IRQ_SAVE;
76 pChipcHw->PLLConfig2 =
77 chipcHw_REG_PLL_CONFIG_D_RESET |
78 chipcHw_REG_PLL_CONFIG_A_RESET;
79
80 pllPreDivider2 = chipcHw_REG_PLL_PREDIVIDER_POWER_DOWN |
81 chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_INTEGER |
82 (chipcHw_REG_PLL_PREDIVIDER_NDIV_i(vcoFreqHz) <<
83 chipcHw_REG_PLL_PREDIVIDER_NDIV_SHIFT) |
84 (chipcHw_REG_PLL_PREDIVIDER_P1 <<
85 chipcHw_REG_PLL_PREDIVIDER_P1_SHIFT) |
86 (chipcHw_REG_PLL_PREDIVIDER_P2 <<
87 chipcHw_REG_PLL_PREDIVIDER_P2_SHIFT);
88
89 /* Enable CHIPC registers to control the PLL */
90 pChipcHw->PLLStatus |= chipcHw_REG_PLL_STATUS_CONTROL_ENABLE;
91
92 /* Set pre divider to get desired VCO frequency */
93 pChipcHw->PLLPreDivider2 = pllPreDivider2;
94 /* Set NDIV Frac */
95 pChipcHw->PLLDivider2 = chipcHw_REG_PLL_DIVIDER_NDIV_f;
96
97 /* This has to be removed once the default values are fixed for PLL2. */
98 pChipcHw->PLLControl12 = 0x38000700;
99 pChipcHw->PLLControl22 = 0x00000015;
100
101 /* Reset PLL2 */
102 if (vcoFreqHz > chipcHw_REG_PLL_CONFIG_VCO_SPLIT_FREQ) {
103 pChipcHw->PLLConfig2 = chipcHw_REG_PLL_CONFIG_D_RESET |
104 chipcHw_REG_PLL_CONFIG_A_RESET |
105 chipcHw_REG_PLL_CONFIG_VCO_1601_3200 |
106 chipcHw_REG_PLL_CONFIG_POWER_DOWN;
107 } else {
108 pChipcHw->PLLConfig2 = chipcHw_REG_PLL_CONFIG_D_RESET |
109 chipcHw_REG_PLL_CONFIG_A_RESET |
110 chipcHw_REG_PLL_CONFIG_VCO_800_1600 |
111 chipcHw_REG_PLL_CONFIG_POWER_DOWN;
112 }
113 REG_LOCAL_IRQ_RESTORE;
114 }
115
116 /* Insert certain amount of delay before deasserting ARESET. */
117 udelay(1);
118
119 {
120 REG_LOCAL_IRQ_SAVE;
121 /* Remove analog reset and Power on the PLL */
122 pChipcHw->PLLConfig2 &=
123 ~(chipcHw_REG_PLL_CONFIG_A_RESET |
124 chipcHw_REG_PLL_CONFIG_POWER_DOWN);
125
126 REG_LOCAL_IRQ_RESTORE;
127
128 }
129
130 /* Wait until PLL is locked */
131 while (!(pChipcHw->PLLStatus2 & chipcHw_REG_PLL_STATUS_LOCKED))
132 ;
133
134 {
135 REG_LOCAL_IRQ_SAVE;
136 /* Remove digital reset */
137 pChipcHw->PLLConfig2 &= ~chipcHw_REG_PLL_CONFIG_D_RESET;
138
139 REG_LOCAL_IRQ_RESTORE;
140 }
141 }
142
143 EXPORT_SYMBOL(chipcHw_pll2Enable);
144
145 /****************************************************************************/
146 /**
147 * @brief Initializes the PLL1
148 *
149 * This function initializes the PLL1
150 *
151 */
152 /****************************************************************************/
chipcHw_pll1Enable(uint32_t vcoFreqHz,chipcHw_SPREAD_SPECTRUM_e ssSupport)153 void chipcHw_pll1Enable(uint32_t vcoFreqHz, chipcHw_SPREAD_SPECTRUM_e ssSupport)
154 {
155 uint32_t pllPreDivider = 0;
156
157 {
158 REG_LOCAL_IRQ_SAVE;
159
160 pChipcHw->PLLConfig =
161 chipcHw_REG_PLL_CONFIG_D_RESET |
162 chipcHw_REG_PLL_CONFIG_A_RESET;
163 /* Setting VCO frequency */
164 if (ssSupport == chipcHw_SPREAD_SPECTRUM_ALLOW) {
165 pllPreDivider =
166 chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_MASH_1_8 |
167 ((chipcHw_REG_PLL_PREDIVIDER_NDIV_i(vcoFreqHz) -
168 1) << chipcHw_REG_PLL_PREDIVIDER_NDIV_SHIFT) |
169 (chipcHw_REG_PLL_PREDIVIDER_P1 <<
170 chipcHw_REG_PLL_PREDIVIDER_P1_SHIFT) |
171 (chipcHw_REG_PLL_PREDIVIDER_P2 <<
172 chipcHw_REG_PLL_PREDIVIDER_P2_SHIFT);
173 } else {
174 pllPreDivider = chipcHw_REG_PLL_PREDIVIDER_POWER_DOWN |
175 chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_INTEGER |
176 (chipcHw_REG_PLL_PREDIVIDER_NDIV_i(vcoFreqHz) <<
177 chipcHw_REG_PLL_PREDIVIDER_NDIV_SHIFT) |
178 (chipcHw_REG_PLL_PREDIVIDER_P1 <<
179 chipcHw_REG_PLL_PREDIVIDER_P1_SHIFT) |
180 (chipcHw_REG_PLL_PREDIVIDER_P2 <<
181 chipcHw_REG_PLL_PREDIVIDER_P2_SHIFT);
182 }
183
184 /* Enable CHIPC registers to control the PLL */
185 pChipcHw->PLLStatus |= chipcHw_REG_PLL_STATUS_CONTROL_ENABLE;
186
187 /* Set pre divider to get desired VCO frequency */
188 pChipcHw->PLLPreDivider = pllPreDivider;
189 /* Set NDIV Frac */
190 if (ssSupport == chipcHw_SPREAD_SPECTRUM_ALLOW) {
191 pChipcHw->PLLDivider = chipcHw_REG_PLL_DIVIDER_M1DIV |
192 chipcHw_REG_PLL_DIVIDER_NDIV_f_SS;
193 } else {
194 pChipcHw->PLLDivider = chipcHw_REG_PLL_DIVIDER_M1DIV |
195 chipcHw_REG_PLL_DIVIDER_NDIV_f;
196 }
197
198 /* Reset PLL1 */
199 if (vcoFreqHz > chipcHw_REG_PLL_CONFIG_VCO_SPLIT_FREQ) {
200 pChipcHw->PLLConfig = chipcHw_REG_PLL_CONFIG_D_RESET |
201 chipcHw_REG_PLL_CONFIG_A_RESET |
202 chipcHw_REG_PLL_CONFIG_VCO_1601_3200 |
203 chipcHw_REG_PLL_CONFIG_POWER_DOWN;
204 } else {
205 pChipcHw->PLLConfig = chipcHw_REG_PLL_CONFIG_D_RESET |
206 chipcHw_REG_PLL_CONFIG_A_RESET |
207 chipcHw_REG_PLL_CONFIG_VCO_800_1600 |
208 chipcHw_REG_PLL_CONFIG_POWER_DOWN;
209 }
210
211 REG_LOCAL_IRQ_RESTORE;
212
213 /* Insert certain amount of delay before deasserting ARESET. */
214 udelay(1);
215
216 {
217 REG_LOCAL_IRQ_SAVE;
218 /* Remove analog reset and Power on the PLL */
219 pChipcHw->PLLConfig &=
220 ~(chipcHw_REG_PLL_CONFIG_A_RESET |
221 chipcHw_REG_PLL_CONFIG_POWER_DOWN);
222 REG_LOCAL_IRQ_RESTORE;
223 }
224
225 /* Wait until PLL is locked */
226 while (!(pChipcHw->PLLStatus & chipcHw_REG_PLL_STATUS_LOCKED)
227 || !(pChipcHw->
228 PLLStatus2 & chipcHw_REG_PLL_STATUS_LOCKED))
229 ;
230
231 /* Remove digital reset */
232 {
233 REG_LOCAL_IRQ_SAVE;
234 pChipcHw->PLLConfig &= ~chipcHw_REG_PLL_CONFIG_D_RESET;
235 REG_LOCAL_IRQ_RESTORE;
236 }
237 }
238 }
239
240 EXPORT_SYMBOL(chipcHw_pll1Enable);
241
242 /****************************************************************************/
243 /**
244 * @brief Initializes the chipc module
245 *
246 * This function initializes the PLLs and core system clocks
247 *
248 */
249 /****************************************************************************/
250
chipcHw_Init(chipcHw_INIT_PARAM_t * initParam)251 void chipcHw_Init(chipcHw_INIT_PARAM_t *initParam /* [ IN ] Misc chip initialization parameter */
252 ) {
253 #if !(defined(__KERNEL__) && !defined(STANDALONE))
254 delay_init();
255 #endif
256
257 /* Do not program PLL, when warm reset */
258 if (!(chipcHw_getStickyBits() & chipcHw_REG_STICKY_CHIP_WARM_RESET)) {
259 chipcHw_pll1Enable(initParam->pllVcoFreqHz,
260 initParam->ssSupport);
261 chipcHw_pll2Enable(initParam->pll2VcoFreqHz);
262 } else {
263 /* Clear sticky bits */
264 chipcHw_clearStickyBits(chipcHw_REG_STICKY_CHIP_WARM_RESET);
265 }
266 /* Clear sticky bits */
267 chipcHw_clearStickyBits(chipcHw_REG_STICKY_CHIP_SOFT_RESET);
268
269 /* Before configuring the ARM clock, atleast we need to make sure BUS clock maintains the proper ratio with ARM clock */
270 pChipcHw->ACLKClock =
271 (pChipcHw->
272 ACLKClock & ~chipcHw_REG_ACLKClock_CLK_DIV_MASK) | (initParam->
273 armBusRatio &
274 chipcHw_REG_ACLKClock_CLK_DIV_MASK);
275
276 /* Set various core component frequencies. The order in which this is done is important for some. */
277 /* The RTBUS (DDR PHY) is derived from the BUS, and the BUS from the ARM, and VPM needs to know BUS */
278 /* frequency to find its ratio with the BUS. Hence we must set the ARM first, followed by the BUS, */
279 /* then VPM and RTBUS. */
280
281 chipcHw_setClockFrequency(chipcHw_CLOCK_ARM,
282 initParam->busClockFreqHz *
283 initParam->armBusRatio);
284 chipcHw_setClockFrequency(chipcHw_CLOCK_BUS, initParam->busClockFreqHz);
285 chipcHw_setClockFrequency(chipcHw_CLOCK_VPM,
286 initParam->busClockFreqHz *
287 initParam->vpmBusRatio);
288 chipcHw_setClockFrequency(chipcHw_CLOCK_DDR,
289 initParam->busClockFreqHz *
290 initParam->ddrBusRatio);
291 chipcHw_setClockFrequency(chipcHw_CLOCK_RTBUS,
292 initParam->busClockFreqHz / 2);
293 }
294