1 /* 2 * uninorth.h: definitions for using the "UniNorth" host bridge chip 3 * from Apple. This chip is used on "Core99" machines 4 * This also includes U2 used on more recent MacRISC2/3 5 * machines and U3 (G5) 6 * 7 */ 8 #ifdef __KERNEL__ 9 #ifndef __ASM_UNINORTH_H__ 10 #define __ASM_UNINORTH_H__ 11 12 /* 13 * Uni-N and U3 config space reg. definitions 14 * 15 * (Little endian) 16 */ 17 18 /* Address ranges selection. This one should work with Bandit too */ 19 /* Not U3 */ 20 #define UNI_N_ADDR_SELECT 0x48 21 #define UNI_N_ADDR_COARSE_MASK 0xffff0000 /* 256Mb regions at *0000000 */ 22 #define UNI_N_ADDR_FINE_MASK 0x0000ffff /* 16Mb regions at f*000000 */ 23 24 /* AGP registers */ 25 /* Not U3 */ 26 #define UNI_N_CFG_GART_BASE 0x8c 27 #define UNI_N_CFG_AGP_BASE 0x90 28 #define UNI_N_CFG_GART_CTRL 0x94 29 #define UNI_N_CFG_INTERNAL_STATUS 0x98 30 #define UNI_N_CFG_GART_DUMMY_PAGE 0xa4 31 32 /* UNI_N_CFG_GART_CTRL bits definitions */ 33 #define UNI_N_CFG_GART_INVAL 0x00000001 34 #define UNI_N_CFG_GART_ENABLE 0x00000100 35 #define UNI_N_CFG_GART_2xRESET 0x00010000 36 #define UNI_N_CFG_GART_DISSBADET 0x00020000 37 /* The following seems to only be used only on U3 <j.glisse@gmail.com> */ 38 #define U3_N_CFG_GART_SYNCMODE 0x00040000 39 #define U3_N_CFG_GART_PERFRD 0x00080000 40 #define U3_N_CFG_GART_B2BGNT 0x00200000 41 #define U3_N_CFG_GART_FASTDDR 0x00400000 42 43 /* My understanding of UniNorth AGP as of UniNorth rev 1.0x, 44 * revision 1.5 (x4 AGP) may need further changes. 45 * 46 * AGP_BASE register contains the base address of the AGP aperture on 47 * the AGP bus. It doesn't seem to be visible to the CPU as of UniNorth 1.x, 48 * even if decoding of this address range is enabled in the address select 49 * register. Apparently, the only supported bases are 256Mb multiples 50 * (high 4 bits of that register). 51 * 52 * GART_BASE register appear to contain the physical address of the GART 53 * in system memory in the high address bits (page aligned), and the 54 * GART size in the low order bits (number of GART pages) 55 * 56 * The GART format itself is one 32bits word per physical memory page. 57 * This word contains, in little-endian format (!!!), the physical address 58 * of the page in the high bits, and what appears to be an "enable" bit 59 * in the LSB bit (0) that must be set to 1 when the entry is valid. 60 * 61 * Obviously, the GART is not cache coherent and so any change to it 62 * must be flushed to memory (or maybe just make the GART space non 63 * cachable). AGP memory itself doesn't seem to be cache coherent neither. 64 * 65 * In order to invalidate the GART (which is probably necessary to inval 66 * the bridge internal TLBs), the following sequence has to be written, 67 * in order, to the GART_CTRL register: 68 * 69 * UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_INVAL 70 * UNI_N_CFG_GART_ENABLE 71 * UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_2xRESET 72 * UNI_N_CFG_GART_ENABLE 73 * 74 * As far as AGP "features" are concerned, it looks like fast write may 75 * not be supported but this has to be confirmed. 76 * 77 * Turning on AGP seem to require a double invalidate operation, one before 78 * setting the AGP command register, on after. 79 * 80 * Turning off AGP seems to require the following sequence: first wait 81 * for the AGP to be idle by reading the internal status register, then 82 * write in that order to the GART_CTRL register: 83 * 84 * UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_INVAL 85 * 0 86 * UNI_N_CFG_GART_2xRESET 87 * 0 88 */ 89 90 /* 91 * Uni-N memory mapped reg. definitions 92 * 93 * Those registers are Big-Endian !! 94 * 95 * Their meaning come from either Darwin and/or from experiments I made with 96 * the bootrom, I'm not sure about their exact meaning yet 97 * 98 */ 99 100 /* Version of the UniNorth chip */ 101 #define UNI_N_VERSION 0x0000 /* Known versions: 3,7 and 8 */ 102 103 #define UNI_N_VERSION_107 0x0003 /* 1.0.7 */ 104 #define UNI_N_VERSION_10A 0x0007 /* 1.0.10 */ 105 #define UNI_N_VERSION_150 0x0011 /* 1.5 */ 106 #define UNI_N_VERSION_200 0x0024 /* 2.0 */ 107 #define UNI_N_VERSION_PANGEA 0x00C0 /* Integrated U1 + K */ 108 #define UNI_N_VERSION_INTREPID 0x00D2 /* Integrated U2 + K */ 109 #define UNI_N_VERSION_300 0x0030 /* 3.0 (U3 on G5) */ 110 111 /* This register is used to enable/disable various clocks */ 112 #define UNI_N_CLOCK_CNTL 0x0020 113 #define UNI_N_CLOCK_CNTL_PCI 0x00000001 /* PCI2 clock control */ 114 #define UNI_N_CLOCK_CNTL_GMAC 0x00000002 /* GMAC clock control */ 115 #define UNI_N_CLOCK_CNTL_FW 0x00000004 /* FireWire clock control */ 116 #define UNI_N_CLOCK_CNTL_ATA100 0x00000010 /* ATA-100 clock control (U2) */ 117 118 /* Power Management control */ 119 #define UNI_N_POWER_MGT 0x0030 120 #define UNI_N_POWER_MGT_NORMAL 0x00 121 #define UNI_N_POWER_MGT_IDLE2 0x01 122 #define UNI_N_POWER_MGT_SLEEP 0x02 123 124 /* This register is configured by Darwin depending on the UniN 125 * revision 126 */ 127 #define UNI_N_ARB_CTRL 0x0040 128 #define UNI_N_ARB_CTRL_QACK_DELAY_SHIFT 15 129 #define UNI_N_ARB_CTRL_QACK_DELAY_MASK 0x0e1f8000 130 #define UNI_N_ARB_CTRL_QACK_DELAY 0x30 131 #define UNI_N_ARB_CTRL_QACK_DELAY105 0x00 132 133 /* This one _might_ return the CPU number of the CPU reading it; 134 * the bootROM decides whether to boot or to sleep/spinloop depending 135 * on this register beeing 0 or not 136 */ 137 #define UNI_N_CPU_NUMBER 0x0050 138 139 /* This register appear to be read by the bootROM to decide what 140 * to do on a non-recoverable reset (powerup or wakeup) 141 */ 142 #define UNI_N_HWINIT_STATE 0x0070 143 #define UNI_N_HWINIT_STATE_SLEEPING 0x01 144 #define UNI_N_HWINIT_STATE_RUNNING 0x02 145 /* This last bit appear to be used by the bootROM to know the second 146 * CPU has started and will enter it's sleep loop with IP=0 147 */ 148 #define UNI_N_HWINIT_STATE_CPU1_FLAG 0x10000000 149 150 /* This register controls AACK delay, which is set when 2004 iBook/PowerBook 151 * is in low speed mode. 152 */ 153 #define UNI_N_AACK_DELAY 0x0100 154 #define UNI_N_AACK_DELAY_ENABLE 0x00000001 155 156 /* Clock status for Intrepid */ 157 #define UNI_N_CLOCK_STOP_STATUS0 0x0150 158 #define UNI_N_CLOCK_STOPPED_EXTAGP 0x00200000 159 #define UNI_N_CLOCK_STOPPED_AGPDEL 0x00100000 160 #define UNI_N_CLOCK_STOPPED_I2S0_45_49 0x00080000 161 #define UNI_N_CLOCK_STOPPED_I2S0_18 0x00040000 162 #define UNI_N_CLOCK_STOPPED_I2S1_45_49 0x00020000 163 #define UNI_N_CLOCK_STOPPED_I2S1_18 0x00010000 164 #define UNI_N_CLOCK_STOPPED_TIMER 0x00008000 165 #define UNI_N_CLOCK_STOPPED_SCC_RTCLK18 0x00004000 166 #define UNI_N_CLOCK_STOPPED_SCC_RTCLK32 0x00002000 167 #define UNI_N_CLOCK_STOPPED_SCC_VIA32 0x00001000 168 #define UNI_N_CLOCK_STOPPED_SCC_SLOT0 0x00000800 169 #define UNI_N_CLOCK_STOPPED_SCC_SLOT1 0x00000400 170 #define UNI_N_CLOCK_STOPPED_SCC_SLOT2 0x00000200 171 #define UNI_N_CLOCK_STOPPED_PCI_FBCLKO 0x00000100 172 #define UNI_N_CLOCK_STOPPED_VEO0 0x00000080 173 #define UNI_N_CLOCK_STOPPED_VEO1 0x00000040 174 #define UNI_N_CLOCK_STOPPED_USB0 0x00000020 175 #define UNI_N_CLOCK_STOPPED_USB1 0x00000010 176 #define UNI_N_CLOCK_STOPPED_USB2 0x00000008 177 #define UNI_N_CLOCK_STOPPED_32 0x00000004 178 #define UNI_N_CLOCK_STOPPED_45 0x00000002 179 #define UNI_N_CLOCK_STOPPED_49 0x00000001 180 181 #define UNI_N_CLOCK_STOP_STATUS1 0x0160 182 #define UNI_N_CLOCK_STOPPED_PLL4REF 0x00080000 183 #define UNI_N_CLOCK_STOPPED_CPUDEL 0x00040000 184 #define UNI_N_CLOCK_STOPPED_CPU 0x00020000 185 #define UNI_N_CLOCK_STOPPED_BUF_REFCKO 0x00010000 186 #define UNI_N_CLOCK_STOPPED_PCI2 0x00008000 187 #define UNI_N_CLOCK_STOPPED_FW 0x00004000 188 #define UNI_N_CLOCK_STOPPED_GB 0x00002000 189 #define UNI_N_CLOCK_STOPPED_ATA66 0x00001000 190 #define UNI_N_CLOCK_STOPPED_ATA100 0x00000800 191 #define UNI_N_CLOCK_STOPPED_MAX 0x00000400 192 #define UNI_N_CLOCK_STOPPED_PCI1 0x00000200 193 #define UNI_N_CLOCK_STOPPED_KLPCI 0x00000100 194 #define UNI_N_CLOCK_STOPPED_USB0PCI 0x00000080 195 #define UNI_N_CLOCK_STOPPED_USB1PCI 0x00000040 196 #define UNI_N_CLOCK_STOPPED_USB2PCI 0x00000020 197 #define UNI_N_CLOCK_STOPPED_7PCI1 0x00000008 198 #define UNI_N_CLOCK_STOPPED_AGP 0x00000004 199 #define UNI_N_CLOCK_STOPPED_PCI0 0x00000002 200 #define UNI_N_CLOCK_STOPPED_18 0x00000001 201 202 /* Intrepid registe to OF do-platform-clockspreading */ 203 #define UNI_N_CLOCK_SPREADING 0x190 204 205 /* Uninorth 1.5 rev. has additional perf. monitor registers at 0xf00-0xf50 */ 206 207 208 /* 209 * U3 specific registers 210 */ 211 212 213 /* U3 Toggle */ 214 #define U3_TOGGLE_REG 0x00e0 215 #define U3_PMC_START_STOP 0x0001 216 #define U3_MPIC_RESET 0x0002 217 #define U3_MPIC_OUTPUT_ENABLE 0x0004 218 219 /* U3 API PHY Config 1 */ 220 #define U3_API_PHY_CONFIG_1 0x23030 221 222 /* U3 HyperTransport registers */ 223 #define U3_HT_CONFIG_BASE 0x70000 224 #define U3_HT_LINK_COMMAND 0x100 225 #define U3_HT_LINK_CONFIG 0x110 226 #define U3_HT_LINK_FREQ 0x120 227 228 #endif /* __ASM_UNINORTH_H__ */ 229 #endif /* __KERNEL__ */ 230