1 #ifndef __ASM_ARCH_PXA3xx_U2D_H 2 #define __ASM_ARCH_PXA3xx_U2D_H 3 4 #include <mach/bitfield.h> 5 6 /* 7 * USB2 device controller registers and bits definitions 8 */ 9 #define U2DCR (0x0000) /* U2D Control Register */ 10 #define U2DCR_NDC (1 << 31) /* NAK During Config */ 11 #define U2DCR_HSTC (0x7 << 28) /* High Speed Timeout Calibration */ 12 #define U2DCR_SPEOREN (1 << 27) /* Short Packet EOR INTR generation Enable */ 13 #define U2DCR_FSTC (0x7 << 24) /* Full Speed Timeout Calibration */ 14 #define U2DCR_UCLKOVR (1 << 22) /* UTM Clock Override */ 15 #define U2DCR_ABP (1 << 21) /* Application Bus Power */ 16 #define U2DCR_ADD (1 << 20) /* Application Device Disconnect */ 17 #define U2DCR_CC (1 << 19) /* Configuration Change */ 18 #define U2DCR_HS (1 << 18) /* High Speed USB Detection */ 19 #define U2DCR_SMAC (1 << 17) /* Switch Endpoint Memory to Active Configuration */ 20 #define U2DCR_DWRE (1 << 16) /* Device Remote Wake-up Feature */ 21 #define U2DCR_ACN (0xf << 12) /* Active U2D Configuration Number */ 22 #define U2DCR_AIN (0xf << 8) /* Active U2D Interface Number */ 23 #define U2DCR_AAISN (0xf << 4) /* Active U2D Alternate Interface Setting Number */ 24 #define U2DCR_EMCE (1 << 3) /* Endpoint Memory Configuration Error */ 25 #define U2DCR_UDR (1 << 2) /* U2D Resume */ 26 #define U2DCR_UDA (1 << 1) /* U2D Active */ 27 #define U2DCR_UDE (1 << 0) /* U2D Enable */ 28 29 #define U2DICR (0x0004) /* U2D Interrupt Control Register */ 30 #define U2DISR (0x000C) /* U2D Interrupt Status Register */ 31 #define U2DINT_CC (1 << 31) /* Interrupt - Configuration Change */ 32 #define U2DINT_SOF (1 << 30) /* Interrupt - SOF */ 33 #define U2DINT_USOF (1 << 29) /* Interrupt - micro SOF */ 34 #define U2DINT_RU (1 << 28) /* Interrupt - Resume */ 35 #define U2DINT_SU (1 << 27) /* Interrupt - Suspend */ 36 #define U2DINT_RS (1 << 26) /* Interrupt - Reset */ 37 #define U2DINT_DPE (1 << 25) /* Interrupt - Data Packet Error */ 38 #define U2DINT_FIFOERR (0x4) /* Interrupt - endpoint FIFO error */ 39 #define U2DINT_PACKETCMP (0x2) /* Interrupt - endpoint packet complete */ 40 #define U2DINT_SPACKETCMP (0x1) /* Interrupt - endpoint short packet complete */ 41 42 #define U2DFNR (0x0014) /* U2D Frame Number Register */ 43 44 #define U2DINT(n, intr) (((intr) & 0x07) << (((n) & 0x07) * 3)) 45 #define U2DICR2 (0x0008) /* U2D Interrupt Control Register 2 */ 46 #define U2DISR2 (0x0010) /* U2D Interrupt Status Register 2 */ 47 48 #define U2DOTGCR (0x0020) /* U2D OTG Control Register */ 49 #define U2DOTGCR_OTGEN (1 << 31) /* On-The-Go Enable */ 50 #define U2DOTGCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation Protocal Port Support */ 51 #define U2DOTGCR_AHNP (1 << 29) /* A-device Host Negotiation Protocal Support */ 52 #define U2DOTGCR_BHNP (1 << 28) /* B-device Host Negotiation Protocal Enable */ 53 54 #ifdef CONFIG_CPU_PXA930 55 #define U2DOTGCR_LPA (1 << 15) /* ULPI low power mode active */ 56 #define U2DOTGCR_IESI (1 << 13) /* OTG interrupt Enable */ 57 #define U2DOTGCR_ISSI (1 << 12) /* OTG interrupt status */ 58 #endif 59 60 #define U2DOTGCR_CKAF (1 << 5) /* Carkit Mode Alternate Function Select */ 61 #define U2DOTGCR_UTMID (1 << 4) /* UTMI Interface Disable */ 62 #define U2DOTGCR_ULAF (1 << 3) /* ULPI Mode Alternate Function Select */ 63 #define U2DOTGCR_SMAF (1 << 2) /* Serial Mode Alternate Function Select */ 64 #define U2DOTGCR_RTSM (1 << 1) /* Return to Synchronous Mode (ULPI Mode) */ 65 #define U2DOTGCR_ULE (1 << 0) /* ULPI Wrapper Enable */ 66 67 #define U2DOTGICR (0x0024) /* U2D OTG Interrupt Control Register */ 68 #define U2DOTGISR (0x0028) /* U2D OTG Interrupt Status Register */ 69 70 #define U2DOTGINT_SF (1 << 17) /* OTG Set Feature Command Received */ 71 #define U2DOTGINT_SI (1 << 16) /* OTG Interrupt */ 72 #define U2DOTGINT_RLS1 (1 << 14) /* RXCMD Linestate[1] Change Interrupt Rise */ 73 #define U2DOTGINT_RLS0 (1 << 13) /* RXCMD Linestate[0] Change Interrupt Rise */ 74 #define U2DOTGINT_RID (1 << 12) /* RXCMD OTG ID Change Interrupt Rise */ 75 #define U2DOTGINT_RSE (1 << 11) /* RXCMD OTG Session End Interrupt Rise */ 76 #define U2DOTGINT_RSV (1 << 10) /* RXCMD OTG Session Valid Interrupt Rise */ 77 #define U2DOTGINT_RVV (1 << 9) /* RXCMD OTG Vbus Valid Interrupt Rise */ 78 #define U2DOTGINT_RCK (1 << 8) /* RXCMD Carkit Interrupt Rise */ 79 #define U2DOTGINT_FLS1 (1 << 6) /* RXCMD Linestate[1] Change Interrupt Fall */ 80 #define U2DOTGINT_FLS0 (1 << 5) /* RXCMD Linestate[0] Change Interrupt Fall */ 81 #define U2DOTGINT_FID (1 << 4) /* RXCMD OTG ID Change Interrupt Fall */ 82 #define U2DOTGINT_FSE (1 << 3) /* RXCMD OTG Session End Interrupt Fall */ 83 #define U2DOTGINT_FSV (1 << 2) /* RXCMD OTG Session Valid Interrupt Fall */ 84 #define U2DOTGINT_FVV (1 << 1) /* RXCMD OTG Vbus Valid Interrupt Fall */ 85 #define U2DOTGINT_FCK (1 << 0) /* RXCMD Carkit Interrupt Fall */ 86 87 #define U2DOTGUSR (0x002C) /* U2D OTG ULPI Status Register */ 88 #define U2DOTGUSR_LPA (1 << 31) /* ULPI Low Power Mode Active */ 89 #define U2DOTGUSR_S6A (1 << 30) /* ULPI Serial Mode (6-pin) Active */ 90 #define U2DOTGUSR_S3A (1 << 29) /* ULPI Serial Mode (3-pin) Active */ 91 #define U2DOTGUSR_CKA (1 << 28) /* ULPI Car Kit Mode Active */ 92 #define U2DOTGUSR_LS1 (1 << 6) /* RXCMD Linestate 1 Status */ 93 #define U2DOTGUSR_LS0 (1 << 5) /* RXCMD Linestate 0 Status */ 94 #define U2DOTGUSR_ID (1 << 4) /* OTG IDGnd Status */ 95 #define U2DOTGUSR_SE (1 << 3) /* OTG Session End Status */ 96 #define U2DOTGUSR_SV (1 << 2) /* OTG Session Valid Status */ 97 #define U2DOTGUSR_VV (1 << 1) /* OTG Vbus Valid Status */ 98 #define U2DOTGUSR_CK (1 << 0) /* Carkit Interrupt Status */ 99 100 #define U2DOTGUCR (0x0030) /* U2D OTG ULPI Control Register */ 101 #define U2DOTGUCR_RUN (1 << 25) /* RUN */ 102 #define U2DOTGUCR_RNW (1 << 24) /* Read or Write operation */ 103 #define U2DOTGUCR_ADDR (0x3f << 16) /* Address of the ULPI PHY register */ 104 #define U2DOTGUCR_WDATA (0xff << 8) /* The data for a WRITE command */ 105 #define U2DOTGUCR_RDATA (0xff << 0) /* The data for a READ command */ 106 107 #define U2DP3CR (0x0034) /* U2D Port 3 Control Register */ 108 #define U2DP3CR_P2SS (0x3 << 8) /* Host Port 2 Serial Mode Select */ 109 #define U2DP3CR_P3SS (0x7 << 4) /* Host Port 3 Serial Mode Select */ 110 #define U2DP3CR_VPVMBEN (0x1 << 2) /* Host Port 3 Vp/Vm Block Enable */ 111 #define U2DP3CR_CFG (0x3 << 0) /* Host Port 3 Configuration */ 112 113 #define U2DCSR0 (0x0100) /* U2D Control/Status Register - Endpoint 0 */ 114 #define U2DCSR0_IPA (1 << 8) /* IN Packet Adjusted */ 115 #define U2DCSR0_SA (1 << 7) /* SETUP Active */ 116 #define U2DCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */ 117 #define U2DCSR0_FST (1 << 5) /* Force Stall */ 118 #define U2DCSR0_SST (1 << 4) /* Send Stall */ 119 #define U2DCSR0_DME (1 << 3) /* DMA Enable */ 120 #define U2DCSR0_FTF (1 << 2) /* Flush Transmit FIFO */ 121 #define U2DCSR0_IPR (1 << 1) /* IN Packet Ready */ 122 #define U2DCSR0_OPC (1 << 0) /* OUT Packet Complete */ 123 124 #define U2DCSR(x) (0x0100 + ((x) << 2)) /* U2D Control/Status Register - Endpoint x */ 125 #define U2DCSR_BF (1 << 10) /* Buffer Full, for OUT eps */ 126 #define U2DCSR_BE (1 << 10) /* Buffer Empty, for IN eps */ 127 #define U2DCSR_DPE (1 << 9) /* Data Packet Error, for ISO eps only */ 128 #define U2DCSR_FEF (1 << 8) /* Flush Endpoint FIFO */ 129 #define U2DCSR_SP (1 << 7) /* Short Packet Control/Status, for OUT eps only, readonly */ 130 #define U2DCSR_BNE (1 << 6) /* Buffer Not Empty, for OUT eps */ 131 #define U2DCSR_BNF (1 << 6) /* Buffer Not Full, for IN eps */ 132 #define U2DCSR_FST (1 << 5) /* Force STALL, write 1 set */ 133 #define U2DCSR_SST (1 << 4) /* Sent STALL, write 1 clear */ 134 #define U2DCSR_DME (1 << 3) /* DMA Enable */ 135 #define U2DCSR_TRN (1 << 2) /* Tx/Rx NAK, write 1 clear */ 136 #define U2DCSR_PC (1 << 1) /* Packet Complete, write 1 clear */ 137 #define U2DCSR_FS (1 << 0) /* FIFO needs Service */ 138 139 #define U2DBCR0 (0x0200) /* U2D Byte Count Register - Endpoint 0 */ 140 #define U2DBCR(x) (0x0200 + ((x) << 2)) /* U2D Byte Count Register - Endpoint x */ 141 142 #define U2DDR0 (0x0300) /* U2D Data Register - Endpoint 0 */ 143 144 #define U2DEPCR(x) (0x0400 + ((x) << 2)) /* U2D Configuration Register - Endpoint x */ 145 #define U2DEPCR_EE (1 << 0) /* Endpoint Enable */ 146 #define U2DEPCR_BS_MASK (0x3FE) /* Buffer Size, BS*8=FIFO size, max 8184B = 8KB */ 147 148 #define U2DSCA (0x0500) /* U2D Setup Command Address */ 149 #define U2DSCA_VALUE (0x0120) 150 151 #define U2DEN0 (0x0504) /* U2D Endpoint Information Register - Endpoint 0 */ 152 #define U2DEN(x) (0x0504 + ((x) << 2)) /* U2D Endpoint Information Register - Endpoint x */ 153 154 /* U2DMA registers */ 155 #define U2DMACSR0 (0x1000) /* U2DMA Control/Status Register - Channel 0 */ 156 #define U2DMACSR(x) (0x1000 + ((x) << 2)) /* U2DMA Control/Status Register - Channel x */ 157 #define U2DMACSR_RUN (1 << 31) /* Run Bit (read / write) */ 158 #define U2DMACSR_STOPIRQEN (1 << 29) /* Stop Interrupt Enable (read / write) */ 159 #define U2DMACSR_EORIRQEN (1 << 28) /* End of Receive Interrupt Enable (R/W) */ 160 #define U2DMACSR_EORJMPEN (1 << 27) /* Jump to next descriptor on EOR */ 161 #define U2DMACSR_EORSTOPEN (1 << 26) /* STOP on an EOR */ 162 #define U2DMACSR_RASIRQEN (1 << 23) /* Request After Cnannel Stopped Interrupt Enable */ 163 #define U2DMACSR_MASKRUN (1 << 22) /* Mask Run */ 164 #define U2DMACSR_SCEMC (3 << 18) /* System Bus Split Completion Error Message Class */ 165 #define U2DMACSR_SCEMI (0x1f << 13) /* System Bus Split Completion Error Message Index */ 166 #define U2DMACSR_BUSERRTYPE (7 << 10) /* PX Bus Error Type */ 167 #define U2DMACSR_EORINTR (1 << 9) /* End Of Receive */ 168 #define U2DMACSR_REQPEND (1 << 8) /* Request Pending */ 169 #define U2DMACSR_RASINTR (1 << 4) /* Request After Channel Stopped (read / write 1 clear) */ 170 #define U2DMACSR_STOPINTR (1 << 3) /* Stop Interrupt (read only) */ 171 #define U2DMACSR_ENDINTR (1 << 2) /* End Interrupt (read / write 1 clear) */ 172 #define U2DMACSR_STARTINTR (1 << 1) /* Start Interrupt (read / write 1 clear) */ 173 #define U2DMACSR_BUSERRINTR (1 << 0) /* Bus Error Interrupt (read / write 1 clear) */ 174 175 #define U2DMACR (0x1080) /* U2DMA Control Register */ 176 #define U2DMAINT (0x10F0) /* U2DMA Interrupt Register */ 177 178 #define U2DMABR0 (0x1100) /* U2DMA Branch Register - Channel 0 */ 179 #define U2DMABR(x) (0x1100 + (x) << 2) /* U2DMA Branch Register - Channel x */ 180 181 #define U2DMADADR0 (0x1200) /* U2DMA Descriptor Address Register - Channel 0 */ 182 #define U2DMADADR(x) (0x1200 + (x) * 0x10) /* U2DMA Descriptor Address Register - Channel x */ 183 184 #define U2DMADADR_STOP (1U << 0) 185 186 #define U2DMASADR0 (0x1204) /* U2DMA Source Address Register - Channel 0 */ 187 #define U2DMASADR(x) (0x1204 + (x) * 0x10) /* U2DMA Source Address Register - Channel x */ 188 #define U2DMATADR0 (0x1208) /* U2DMA Target Address Register - Channel 0 */ 189 #define U2DMATADR(x) (0x1208 + (x) * 0x10) /* U2DMA Target Address Register - Channel x */ 190 191 #define U2DMACMDR0 (0x120C) /* U2DMA Command Address Register - Channel 0 */ 192 #define U2DMACMDR(x) (0x120C + (x) * 0x10) /* U2DMA Command Address Register - Channel x */ 193 194 #define U2DMACMDR_XFRDIS (1 << 31) /* Transfer Direction */ 195 #define U2DMACMDR_STARTIRQEN (1 << 22) /* Start Interrupt Enable */ 196 #define U2DMACMDR_ENDIRQEN (1 << 21) /* End Interrupt Enable */ 197 #define U2DMACMDR_PACKCOMP (1 << 13) /* Packet Complete */ 198 #define U2DMACMDR_LEN (0x07ff) /* length mask (max = 2K - 1) */ 199 200 #endif /* __ASM_ARCH_PXA3xx_U2D_H */ 201