1 #ifndef LINUX_SSB_REGS_H_ 2 #define LINUX_SSB_REGS_H_ 3 4 5 /* SiliconBackplane Address Map. 6 * All regions may not exist on all chips. 7 */ 8 #define SSB_SDRAM_BASE 0x00000000U /* Physical SDRAM */ 9 #define SSB_PCI_MEM 0x08000000U /* Host Mode sb2pcitranslation0 (64 MB) */ 10 #define SSB_PCI_CFG 0x0c000000U /* Host Mode sb2pcitranslation1 (64 MB) */ 11 #define SSB_SDRAM_SWAPPED 0x10000000U /* Byteswapped Physical SDRAM */ 12 #define SSB_ENUM_BASE 0x18000000U /* Enumeration space base */ 13 #define SSB_ENUM_LIMIT 0x18010000U /* Enumeration space limit */ 14 15 #define SSB_FLASH2 0x1c000000U /* Flash Region 2 (region 1 shadowed here) */ 16 #define SSB_FLASH2_SZ 0x02000000U /* Size of Flash Region 2 */ 17 18 #define SSB_EXTIF_BASE 0x1f000000U /* External Interface region base address */ 19 #define SSB_FLASH1 0x1fc00000U /* Flash Region 1 */ 20 #define SSB_FLASH1_SZ 0x00400000U /* Size of Flash Region 1 */ 21 22 #define SSB_PCI_DMA 0x40000000U /* Client Mode sb2pcitranslation2 (1 GB) */ 23 #define SSB_PCI_DMA_SZ 0x40000000U /* Client Mode sb2pcitranslation2 size in bytes */ 24 #define SSB_PCIE_DMA_L32 0x00000000U /* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), low 32 bits */ 25 #define SSB_PCIE_DMA_H32 0x80000000U /* PCIE Client Mode sb2pcitranslation2 (2 ZettaBytes), high 32 bits */ 26 #define SSB_EUART (SSB_EXTIF_BASE + 0x00800000) 27 #define SSB_LED (SSB_EXTIF_BASE + 0x00900000) 28 29 30 /* Enumeration space constants */ 31 #define SSB_CORE_SIZE 0x1000 /* Size of a core MMIO area */ 32 #define SSB_MAX_NR_CORES ((SSB_ENUM_LIMIT - SSB_ENUM_BASE) / SSB_CORE_SIZE) 33 34 35 /* mips address */ 36 #define SSB_EJTAG 0xff200000 /* MIPS EJTAG space (2M) */ 37 38 39 /* SSB PCI config space registers. */ 40 #define SSB_PMCSR 0x44 41 #define SSB_PE 0x100 42 #define SSB_BAR0_WIN 0x80 /* Backplane address space 0 */ 43 #define SSB_BAR1_WIN 0x84 /* Backplane address space 1 */ 44 #define SSB_SPROMCTL 0x88 /* SPROM control */ 45 #define SSB_SPROMCTL_WE 0x10 /* SPROM write enable */ 46 #define SSB_BAR1_CONTROL 0x8c /* Address space 1 burst control */ 47 #define SSB_PCI_IRQS 0x90 /* PCI interrupts */ 48 #define SSB_PCI_IRQMASK 0x94 /* PCI IRQ control and mask (pcirev >= 6 only) */ 49 #define SSB_BACKPLANE_IRQS 0x98 /* Backplane Interrupts */ 50 #define SSB_GPIO_IN 0xB0 /* GPIO Input (pcirev >= 3 only) */ 51 #define SSB_GPIO_OUT 0xB4 /* GPIO Output (pcirev >= 3 only) */ 52 #define SSB_GPIO_OUT_ENABLE 0xB8 /* GPIO Output Enable/Disable (pcirev >= 3 only) */ 53 #define SSB_GPIO_SCS 0x10 /* PCI config space bit 4 for 4306c0 slow clock source */ 54 #define SSB_GPIO_HWRAD 0x20 /* PCI config space GPIO 13 for hw radio disable */ 55 #define SSB_GPIO_XTAL 0x40 /* PCI config space GPIO 14 for Xtal powerup */ 56 #define SSB_GPIO_PLL 0x80 /* PCI config space GPIO 15 for PLL powerdown */ 57 58 59 #define SSB_BAR0_MAX_RETRIES 50 60 61 /* Silicon backplane configuration register definitions */ 62 #define SSB_IPSFLAG 0x0F08 63 #define SSB_IPSFLAG_IRQ1 0x0000003F /* which sbflags get routed to mips interrupt 1 */ 64 #define SSB_IPSFLAG_IRQ1_SHIFT 0 65 #define SSB_IPSFLAG_IRQ2 0x00003F00 /* which sbflags get routed to mips interrupt 2 */ 66 #define SSB_IPSFLAG_IRQ2_SHIFT 8 67 #define SSB_IPSFLAG_IRQ3 0x003F0000 /* which sbflags get routed to mips interrupt 3 */ 68 #define SSB_IPSFLAG_IRQ3_SHIFT 16 69 #define SSB_IPSFLAG_IRQ4 0x3F000000 /* which sbflags get routed to mips interrupt 4 */ 70 #define SSB_IPSFLAG_IRQ4_SHIFT 24 71 #define SSB_TPSFLAG 0x0F18 72 #define SSB_TPSFLAG_BPFLAG 0x0000003F /* Backplane flag # */ 73 #define SSB_TPSFLAG_ALWAYSIRQ 0x00000040 /* IRQ is always sent on the Backplane */ 74 #define SSB_TMERRLOGA 0x0F48 75 #define SSB_TMERRLOG 0x0F50 76 #define SSB_ADMATCH3 0x0F60 77 #define SSB_ADMATCH2 0x0F68 78 #define SSB_ADMATCH1 0x0F70 79 #define SSB_IMSTATE 0x0F90 /* SB Initiator Agent State */ 80 #define SSB_IMSTATE_PC 0x0000000f /* Pipe Count */ 81 #define SSB_IMSTATE_AP_MASK 0x00000030 /* Arbitration Priority */ 82 #define SSB_IMSTATE_AP_BOTH 0x00000000 /* Use both timeslices and token */ 83 #define SSB_IMSTATE_AP_TS 0x00000010 /* Use timeslices only */ 84 #define SSB_IMSTATE_AP_TK 0x00000020 /* Use token only */ 85 #define SSB_IMSTATE_AP_RSV 0x00000030 /* Reserved */ 86 #define SSB_IMSTATE_IBE 0x00020000 /* In Band Error */ 87 #define SSB_IMSTATE_TO 0x00040000 /* Timeout */ 88 #define SSB_IMSTATE_BUSY 0x01800000 /* Busy (Backplane rev >= 2.3 only) */ 89 #define SSB_IMSTATE_REJECT 0x02000000 /* Reject (Backplane rev >= 2.3 only) */ 90 #define SSB_INTVEC 0x0F94 /* SB Interrupt Mask */ 91 #define SSB_INTVEC_PCI 0x00000001 /* Enable interrupts for PCI */ 92 #define SSB_INTVEC_ENET0 0x00000002 /* Enable interrupts for enet 0 */ 93 #define SSB_INTVEC_ILINE20 0x00000004 /* Enable interrupts for iline20 */ 94 #define SSB_INTVEC_CODEC 0x00000008 /* Enable interrupts for v90 codec */ 95 #define SSB_INTVEC_USB 0x00000010 /* Enable interrupts for usb */ 96 #define SSB_INTVEC_EXTIF 0x00000020 /* Enable interrupts for external i/f */ 97 #define SSB_INTVEC_ENET1 0x00000040 /* Enable interrupts for enet 1 */ 98 #define SSB_TMSLOW 0x0F98 /* SB Target State Low */ 99 #define SSB_TMSLOW_RESET 0x00000001 /* Reset */ 100 #define SSB_TMSLOW_REJECT_22 0x00000002 /* Reject (Backplane rev 2.2) */ 101 #define SSB_TMSLOW_REJECT_23 0x00000004 /* Reject (Backplane rev 2.3) */ 102 #define SSB_TMSLOW_CLOCK 0x00010000 /* Clock Enable */ 103 #define SSB_TMSLOW_FGC 0x00020000 /* Force Gated Clocks On */ 104 #define SSB_TMSLOW_PE 0x40000000 /* Power Management Enable */ 105 #define SSB_TMSLOW_BE 0x80000000 /* BIST Enable */ 106 #define SSB_TMSHIGH 0x0F9C /* SB Target State High */ 107 #define SSB_TMSHIGH_SERR 0x00000001 /* S-error */ 108 #define SSB_TMSHIGH_INT 0x00000002 /* Interrupt */ 109 #define SSB_TMSHIGH_BUSY 0x00000004 /* Busy */ 110 #define SSB_TMSHIGH_TO 0x00000020 /* Timeout. Backplane rev >= 2.3 only */ 111 #define SSB_TMSHIGH_COREFL 0x1FFF0000 /* Core specific flags */ 112 #define SSB_TMSHIGH_COREFL_SHIFT 16 113 #define SSB_TMSHIGH_DMA64 0x10000000 /* 64bit DMA supported */ 114 #define SSB_TMSHIGH_GCR 0x20000000 /* Gated Clock Request */ 115 #define SSB_TMSHIGH_BISTF 0x40000000 /* BIST Failed */ 116 #define SSB_TMSHIGH_BISTD 0x80000000 /* BIST Done */ 117 #define SSB_BWA0 0x0FA0 118 #define SSB_IMCFGLO 0x0FA8 119 #define SSB_IMCFGLO_SERTO 0x00000007 /* Service timeout */ 120 #define SSB_IMCFGLO_REQTO 0x00000070 /* Request timeout */ 121 #define SSB_IMCFGLO_REQTO_SHIFT 4 122 #define SSB_IMCFGLO_CONNID 0x00FF0000 /* Connection ID */ 123 #define SSB_IMCFGLO_CONNID_SHIFT 16 124 #define SSB_IMCFGHI 0x0FAC 125 #define SSB_ADMATCH0 0x0FB0 126 #define SSB_TMCFGLO 0x0FB8 127 #define SSB_TMCFGHI 0x0FBC 128 #define SSB_BCONFIG 0x0FC0 129 #define SSB_BSTATE 0x0FC8 130 #define SSB_ACTCFG 0x0FD8 131 #define SSB_FLAGST 0x0FE8 132 #define SSB_IDLOW 0x0FF8 133 #define SSB_IDLOW_CFGSP 0x00000003 /* Config Space */ 134 #define SSB_IDLOW_ADDRNGE 0x00000038 /* Address Ranges supported */ 135 #define SSB_IDLOW_ADDRNGE_SHIFT 3 136 #define SSB_IDLOW_SYNC 0x00000040 137 #define SSB_IDLOW_INITIATOR 0x00000080 138 #define SSB_IDLOW_MIBL 0x00000F00 /* Minimum Backplane latency */ 139 #define SSB_IDLOW_MIBL_SHIFT 8 140 #define SSB_IDLOW_MABL 0x0000F000 /* Maximum Backplane latency */ 141 #define SSB_IDLOW_MABL_SHIFT 12 142 #define SSB_IDLOW_TIF 0x00010000 /* This Initiator is first */ 143 #define SSB_IDLOW_CCW 0x000C0000 /* Cycle counter width */ 144 #define SSB_IDLOW_CCW_SHIFT 18 145 #define SSB_IDLOW_TPT 0x00F00000 /* Target ports */ 146 #define SSB_IDLOW_TPT_SHIFT 20 147 #define SSB_IDLOW_INITP 0x0F000000 /* Initiator ports */ 148 #define SSB_IDLOW_INITP_SHIFT 24 149 #define SSB_IDLOW_SSBREV 0xF0000000 /* Sonics Backplane Revision code */ 150 #define SSB_IDLOW_SSBREV_22 0x00000000 /* <= 2.2 */ 151 #define SSB_IDLOW_SSBREV_23 0x10000000 /* 2.3 */ 152 #define SSB_IDLOW_SSBREV_24 0x40000000 /* ?? Found in BCM4328 */ 153 #define SSB_IDLOW_SSBREV_25 0x50000000 /* ?? Not Found yet */ 154 #define SSB_IDLOW_SSBREV_26 0x60000000 /* ?? Found in some BCM4311/2 */ 155 #define SSB_IDLOW_SSBREV_27 0x70000000 /* ?? Found in some BCM4311/2 */ 156 #define SSB_IDHIGH 0x0FFC /* SB Identification High */ 157 #define SSB_IDHIGH_RCLO 0x0000000F /* Revision Code (low part) */ 158 #define SSB_IDHIGH_CC 0x00008FF0 /* Core Code */ 159 #define SSB_IDHIGH_CC_SHIFT 4 160 #define SSB_IDHIGH_RCHI 0x00007000 /* Revision Code (high part) */ 161 #define SSB_IDHIGH_RCHI_SHIFT 8 /* yes, shift 8 is right */ 162 #define SSB_IDHIGH_VC 0xFFFF0000 /* Vendor Code */ 163 #define SSB_IDHIGH_VC_SHIFT 16 164 165 /* SPROM shadow area. If not otherwise noted, fields are 166 * two bytes wide. Note that the SPROM can _only_ be read 167 * in two-byte quantities. 168 */ 169 #define SSB_SPROMSIZE_WORDS 64 170 #define SSB_SPROMSIZE_BYTES (SSB_SPROMSIZE_WORDS * sizeof(u16)) 171 #define SSB_SPROMSIZE_WORDS_R123 64 172 #define SSB_SPROMSIZE_WORDS_R4 220 173 #define SSB_SPROMSIZE_BYTES_R123 (SSB_SPROMSIZE_WORDS_R123 * sizeof(u16)) 174 #define SSB_SPROMSIZE_BYTES_R4 (SSB_SPROMSIZE_WORDS_R4 * sizeof(u16)) 175 #define SSB_SPROM_BASE1 0x1000 176 #define SSB_SPROM_BASE31 0x0800 177 #define SSB_SPROM_REVISION 0x007E 178 #define SSB_SPROM_REVISION_REV 0x00FF /* SPROM Revision number */ 179 #define SSB_SPROM_REVISION_CRC 0xFF00 /* SPROM CRC8 value */ 180 #define SSB_SPROM_REVISION_CRC_SHIFT 8 181 182 /* SPROM Revision 1 */ 183 #define SSB_SPROM1_SPID 0x0004 /* Subsystem Product ID for PCI */ 184 #define SSB_SPROM1_SVID 0x0006 /* Subsystem Vendor ID for PCI */ 185 #define SSB_SPROM1_PID 0x0008 /* Product ID for PCI */ 186 #define SSB_SPROM1_IL0MAC 0x0048 /* 6 bytes MAC address for 802.11b/g */ 187 #define SSB_SPROM1_ET0MAC 0x004E /* 6 bytes MAC address for Ethernet */ 188 #define SSB_SPROM1_ET1MAC 0x0054 /* 6 bytes MAC address for 802.11a */ 189 #define SSB_SPROM1_ETHPHY 0x005A /* Ethernet PHY settings */ 190 #define SSB_SPROM1_ETHPHY_ET0A 0x001F /* MII Address for enet0 */ 191 #define SSB_SPROM1_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */ 192 #define SSB_SPROM1_ETHPHY_ET1A_SHIFT 5 193 #define SSB_SPROM1_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */ 194 #define SSB_SPROM1_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */ 195 #define SSB_SPROM1_BINF 0x005C /* Board info */ 196 #define SSB_SPROM1_BINF_BREV 0x00FF /* Board Revision */ 197 #define SSB_SPROM1_BINF_CCODE 0x0F00 /* Country Code */ 198 #define SSB_SPROM1_BINF_CCODE_SHIFT 8 199 #define SSB_SPROM1_BINF_ANTBG 0x3000 /* Available B-PHY and G-PHY antennas */ 200 #define SSB_SPROM1_BINF_ANTBG_SHIFT 12 201 #define SSB_SPROM1_BINF_ANTA 0xC000 /* Available A-PHY antennas */ 202 #define SSB_SPROM1_BINF_ANTA_SHIFT 14 203 #define SSB_SPROM1_PA0B0 0x005E 204 #define SSB_SPROM1_PA0B1 0x0060 205 #define SSB_SPROM1_PA0B2 0x0062 206 #define SSB_SPROM1_GPIOA 0x0064 /* General Purpose IO pins 0 and 1 */ 207 #define SSB_SPROM1_GPIOA_P0 0x00FF /* Pin 0 */ 208 #define SSB_SPROM1_GPIOA_P1 0xFF00 /* Pin 1 */ 209 #define SSB_SPROM1_GPIOA_P1_SHIFT 8 210 #define SSB_SPROM1_GPIOB 0x0066 /* General Purpuse IO pins 2 and 3 */ 211 #define SSB_SPROM1_GPIOB_P2 0x00FF /* Pin 2 */ 212 #define SSB_SPROM1_GPIOB_P3 0xFF00 /* Pin 3 */ 213 #define SSB_SPROM1_GPIOB_P3_SHIFT 8 214 #define SSB_SPROM1_MAXPWR 0x0068 /* Power Amplifier Max Power */ 215 #define SSB_SPROM1_MAXPWR_BG 0x00FF /* B-PHY and G-PHY (in dBm Q5.2) */ 216 #define SSB_SPROM1_MAXPWR_A 0xFF00 /* A-PHY (in dBm Q5.2) */ 217 #define SSB_SPROM1_MAXPWR_A_SHIFT 8 218 #define SSB_SPROM1_PA1B0 0x006A 219 #define SSB_SPROM1_PA1B1 0x006C 220 #define SSB_SPROM1_PA1B2 0x006E 221 #define SSB_SPROM1_ITSSI 0x0070 /* Idle TSSI Target */ 222 #define SSB_SPROM1_ITSSI_BG 0x00FF /* B-PHY and G-PHY*/ 223 #define SSB_SPROM1_ITSSI_A 0xFF00 /* A-PHY */ 224 #define SSB_SPROM1_ITSSI_A_SHIFT 8 225 #define SSB_SPROM1_BFLLO 0x0072 /* Boardflags (low 16 bits) */ 226 #define SSB_SPROM1_AGAIN 0x0074 /* Antenna Gain (in dBm Q5.2) */ 227 #define SSB_SPROM1_AGAIN_BG 0x00FF /* B-PHY and G-PHY */ 228 #define SSB_SPROM1_AGAIN_BG_SHIFT 0 229 #define SSB_SPROM1_AGAIN_A 0xFF00 /* A-PHY */ 230 #define SSB_SPROM1_AGAIN_A_SHIFT 8 231 232 /* SPROM Revision 2 (inherits from rev 1) */ 233 #define SSB_SPROM2_BFLHI 0x0038 /* Boardflags (high 16 bits) */ 234 #define SSB_SPROM2_MAXP_A 0x003A /* A-PHY Max Power */ 235 #define SSB_SPROM2_MAXP_A_HI 0x00FF /* Max Power High */ 236 #define SSB_SPROM2_MAXP_A_LO 0xFF00 /* Max Power Low */ 237 #define SSB_SPROM2_MAXP_A_LO_SHIFT 8 238 #define SSB_SPROM2_PA1LOB0 0x003C /* A-PHY PowerAmplifier Low Settings */ 239 #define SSB_SPROM2_PA1LOB1 0x003E /* A-PHY PowerAmplifier Low Settings */ 240 #define SSB_SPROM2_PA1LOB2 0x0040 /* A-PHY PowerAmplifier Low Settings */ 241 #define SSB_SPROM2_PA1HIB0 0x0042 /* A-PHY PowerAmplifier High Settings */ 242 #define SSB_SPROM2_PA1HIB1 0x0044 /* A-PHY PowerAmplifier High Settings */ 243 #define SSB_SPROM2_PA1HIB2 0x0046 /* A-PHY PowerAmplifier High Settings */ 244 #define SSB_SPROM2_OPO 0x0078 /* OFDM Power Offset from CCK Level */ 245 #define SSB_SPROM2_OPO_VALUE 0x00FF 246 #define SSB_SPROM2_OPO_UNUSED 0xFF00 247 #define SSB_SPROM2_CCODE 0x007C /* Two char Country Code */ 248 249 /* SPROM Revision 3 (inherits most data from rev 2) */ 250 #define SSB_SPROM3_OFDMAPO 0x002C /* A-PHY OFDM Mid Power Offset (4 bytes, BigEndian) */ 251 #define SSB_SPROM3_OFDMALPO 0x0030 /* A-PHY OFDM Low Power Offset (4 bytes, BigEndian) */ 252 #define SSB_SPROM3_OFDMAHPO 0x0034 /* A-PHY OFDM High Power Offset (4 bytes, BigEndian) */ 253 #define SSB_SPROM3_GPIOLDC 0x0042 /* GPIO LED Powersave Duty Cycle (4 bytes, BigEndian) */ 254 #define SSB_SPROM3_GPIOLDC_OFF 0x0000FF00 /* Off Count */ 255 #define SSB_SPROM3_GPIOLDC_OFF_SHIFT 8 256 #define SSB_SPROM3_GPIOLDC_ON 0x00FF0000 /* On Count */ 257 #define SSB_SPROM3_GPIOLDC_ON_SHIFT 16 258 #define SSB_SPROM3_IL0MAC 0x004A /* 6 bytes MAC address for 802.11b/g */ 259 #define SSB_SPROM3_CCKPO 0x0078 /* CCK Power Offset */ 260 #define SSB_SPROM3_CCKPO_1M 0x000F /* 1M Rate PO */ 261 #define SSB_SPROM3_CCKPO_2M 0x00F0 /* 2M Rate PO */ 262 #define SSB_SPROM3_CCKPO_2M_SHIFT 4 263 #define SSB_SPROM3_CCKPO_55M 0x0F00 /* 5.5M Rate PO */ 264 #define SSB_SPROM3_CCKPO_55M_SHIFT 8 265 #define SSB_SPROM3_CCKPO_11M 0xF000 /* 11M Rate PO */ 266 #define SSB_SPROM3_CCKPO_11M_SHIFT 12 267 #define SSB_SPROM3_OFDMGPO 0x107A /* G-PHY OFDM Power Offset (4 bytes, BigEndian) */ 268 269 /* SPROM Revision 4 */ 270 #define SSB_SPROM4_BFLLO 0x0044 /* Boardflags (low 16 bits) */ 271 #define SSB_SPROM4_BFLHI 0x0046 /* Board Flags Hi */ 272 #define SSB_SPROM4_BFL2LO 0x0048 /* Board flags 2 (low 16 bits) */ 273 #define SSB_SPROM4_BFL2HI 0x004A /* Board flags 2 Hi */ 274 #define SSB_SPROM4_IL0MAC 0x004C /* 6 byte MAC address for a/b/g/n */ 275 #define SSB_SPROM4_CCODE 0x0052 /* Country Code (2 bytes) */ 276 #define SSB_SPROM4_GPIOA 0x0056 /* Gen. Purpose IO # 0 and 1 */ 277 #define SSB_SPROM4_GPIOA_P0 0x00FF /* Pin 0 */ 278 #define SSB_SPROM4_GPIOA_P1 0xFF00 /* Pin 1 */ 279 #define SSB_SPROM4_GPIOA_P1_SHIFT 8 280 #define SSB_SPROM4_GPIOB 0x0058 /* Gen. Purpose IO # 2 and 3 */ 281 #define SSB_SPROM4_GPIOB_P2 0x00FF /* Pin 2 */ 282 #define SSB_SPROM4_GPIOB_P3 0xFF00 /* Pin 3 */ 283 #define SSB_SPROM4_GPIOB_P3_SHIFT 8 284 #define SSB_SPROM4_ETHPHY 0x005A /* Ethernet PHY settings ?? */ 285 #define SSB_SPROM4_ETHPHY_ET0A 0x001F /* MII Address for enet0 */ 286 #define SSB_SPROM4_ETHPHY_ET1A 0x03E0 /* MII Address for enet1 */ 287 #define SSB_SPROM4_ETHPHY_ET1A_SHIFT 5 288 #define SSB_SPROM4_ETHPHY_ET0M (1<<14) /* MDIO for enet0 */ 289 #define SSB_SPROM4_ETHPHY_ET1M (1<<15) /* MDIO for enet1 */ 290 #define SSB_SPROM4_ANTAVAIL 0x005D /* Antenna available bitfields */ 291 #define SSB_SPROM4_ANTAVAIL_A 0x00FF /* A-PHY bitfield */ 292 #define SSB_SPROM4_ANTAVAIL_A_SHIFT 0 293 #define SSB_SPROM4_ANTAVAIL_BG 0xFF00 /* B-PHY and G-PHY bitfield */ 294 #define SSB_SPROM4_ANTAVAIL_BG_SHIFT 8 295 #define SSB_SPROM4_AGAIN01 0x005E /* Antenna Gain (in dBm Q5.2) */ 296 #define SSB_SPROM4_AGAIN0 0x00FF /* Antenna 0 */ 297 #define SSB_SPROM4_AGAIN0_SHIFT 0 298 #define SSB_SPROM4_AGAIN1 0xFF00 /* Antenna 1 */ 299 #define SSB_SPROM4_AGAIN1_SHIFT 8 300 #define SSB_SPROM4_AGAIN23 0x0060 301 #define SSB_SPROM4_AGAIN2 0x00FF /* Antenna 2 */ 302 #define SSB_SPROM4_AGAIN2_SHIFT 0 303 #define SSB_SPROM4_AGAIN3 0xFF00 /* Antenna 3 */ 304 #define SSB_SPROM4_AGAIN3_SHIFT 8 305 #define SSB_SPROM4_TXPID2G01 0x0062 /* TX Power Index 2GHz */ 306 #define SSB_SPROM4_TXPID2G0 0x00FF 307 #define SSB_SPROM4_TXPID2G0_SHIFT 0 308 #define SSB_SPROM4_TXPID2G1 0xFF00 309 #define SSB_SPROM4_TXPID2G1_SHIFT 8 310 #define SSB_SPROM4_TXPID2G23 0x0064 /* TX Power Index 2GHz */ 311 #define SSB_SPROM4_TXPID2G2 0x00FF 312 #define SSB_SPROM4_TXPID2G2_SHIFT 0 313 #define SSB_SPROM4_TXPID2G3 0xFF00 314 #define SSB_SPROM4_TXPID2G3_SHIFT 8 315 #define SSB_SPROM4_TXPID5G01 0x0066 /* TX Power Index 5GHz middle subband */ 316 #define SSB_SPROM4_TXPID5G0 0x00FF 317 #define SSB_SPROM4_TXPID5G0_SHIFT 0 318 #define SSB_SPROM4_TXPID5G1 0xFF00 319 #define SSB_SPROM4_TXPID5G1_SHIFT 8 320 #define SSB_SPROM4_TXPID5G23 0x0068 /* TX Power Index 5GHz middle subband */ 321 #define SSB_SPROM4_TXPID5G2 0x00FF 322 #define SSB_SPROM4_TXPID5G2_SHIFT 0 323 #define SSB_SPROM4_TXPID5G3 0xFF00 324 #define SSB_SPROM4_TXPID5G3_SHIFT 8 325 #define SSB_SPROM4_TXPID5GL01 0x006A /* TX Power Index 5GHz low subband */ 326 #define SSB_SPROM4_TXPID5GL0 0x00FF 327 #define SSB_SPROM4_TXPID5GL0_SHIFT 0 328 #define SSB_SPROM4_TXPID5GL1 0xFF00 329 #define SSB_SPROM4_TXPID5GL1_SHIFT 8 330 #define SSB_SPROM4_TXPID5GL23 0x006C /* TX Power Index 5GHz low subband */ 331 #define SSB_SPROM4_TXPID5GL2 0x00FF 332 #define SSB_SPROM4_TXPID5GL2_SHIFT 0 333 #define SSB_SPROM4_TXPID5GL3 0xFF00 334 #define SSB_SPROM4_TXPID5GL3_SHIFT 8 335 #define SSB_SPROM4_TXPID5GH01 0x006E /* TX Power Index 5GHz high subband */ 336 #define SSB_SPROM4_TXPID5GH0 0x00FF 337 #define SSB_SPROM4_TXPID5GH0_SHIFT 0 338 #define SSB_SPROM4_TXPID5GH1 0xFF00 339 #define SSB_SPROM4_TXPID5GH1_SHIFT 8 340 #define SSB_SPROM4_TXPID5GH23 0x0070 /* TX Power Index 5GHz high subband */ 341 #define SSB_SPROM4_TXPID5GH2 0x00FF 342 #define SSB_SPROM4_TXPID5GH2_SHIFT 0 343 #define SSB_SPROM4_TXPID5GH3 0xFF00 344 #define SSB_SPROM4_TXPID5GH3_SHIFT 8 345 #define SSB_SPROM4_MAXP_BG 0x0080 /* Max Power BG in path 1 */ 346 #define SSB_SPROM4_MAXP_BG_MASK 0x00FF /* Mask for Max Power BG */ 347 #define SSB_SPROM4_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */ 348 #define SSB_SPROM4_ITSSI_BG_SHIFT 8 349 #define SSB_SPROM4_MAXP_A 0x008A /* Max Power A in path 1 */ 350 #define SSB_SPROM4_MAXP_A_MASK 0x00FF /* Mask for Max Power A */ 351 #define SSB_SPROM4_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */ 352 #define SSB_SPROM4_ITSSI_A_SHIFT 8 353 #define SSB_SPROM4_PA0B0 0x0082 /* The paXbY locations are */ 354 #define SSB_SPROM4_PA0B1 0x0084 /* only guesses */ 355 #define SSB_SPROM4_PA0B2 0x0086 356 #define SSB_SPROM4_PA1B0 0x008E 357 #define SSB_SPROM4_PA1B1 0x0090 358 #define SSB_SPROM4_PA1B2 0x0092 359 360 /* SPROM Revision 5 (inherits most data from rev 4) */ 361 #define SSB_SPROM5_CCODE 0x0044 /* Country Code (2 bytes) */ 362 #define SSB_SPROM5_BFLLO 0x004A /* Boardflags (low 16 bits) */ 363 #define SSB_SPROM5_BFLHI 0x004C /* Board Flags Hi */ 364 #define SSB_SPROM5_BFL2LO 0x004E /* Board flags 2 (low 16 bits) */ 365 #define SSB_SPROM5_BFL2HI 0x0050 /* Board flags 2 Hi */ 366 #define SSB_SPROM5_IL0MAC 0x0052 /* 6 byte MAC address for a/b/g/n */ 367 #define SSB_SPROM5_GPIOA 0x0076 /* Gen. Purpose IO # 0 and 1 */ 368 #define SSB_SPROM5_GPIOA_P0 0x00FF /* Pin 0 */ 369 #define SSB_SPROM5_GPIOA_P1 0xFF00 /* Pin 1 */ 370 #define SSB_SPROM5_GPIOA_P1_SHIFT 8 371 #define SSB_SPROM5_GPIOB 0x0078 /* Gen. Purpose IO # 2 and 3 */ 372 #define SSB_SPROM5_GPIOB_P2 0x00FF /* Pin 2 */ 373 #define SSB_SPROM5_GPIOB_P3 0xFF00 /* Pin 3 */ 374 #define SSB_SPROM5_GPIOB_P3_SHIFT 8 375 376 /* SPROM Revision 8 */ 377 #define SSB_SPROM8_BOARDREV 0x0082 /* Board revision */ 378 #define SSB_SPROM8_BFLLO 0x0084 /* Board flags (bits 0-15) */ 379 #define SSB_SPROM8_BFLHI 0x0086 /* Board flags (bits 16-31) */ 380 #define SSB_SPROM8_BFL2LO 0x0088 /* Board flags (bits 32-47) */ 381 #define SSB_SPROM8_BFL2HI 0x008A /* Board flags (bits 48-63) */ 382 #define SSB_SPROM8_IL0MAC 0x008C /* 6 byte MAC address */ 383 #define SSB_SPROM8_CCODE 0x0092 /* 2 byte country code */ 384 #define SSB_SPROM8_GPIOA 0x0096 /*Gen. Purpose IO # 0 and 1 */ 385 #define SSB_SPROM8_GPIOA_P0 0x00FF /* Pin 0 */ 386 #define SSB_SPROM8_GPIOA_P1 0xFF00 /* Pin 1 */ 387 #define SSB_SPROM8_GPIOA_P1_SHIFT 8 388 #define SSB_SPROM8_GPIOB 0x0098 /* Gen. Purpose IO # 2 and 3 */ 389 #define SSB_SPROM8_GPIOB_P2 0x00FF /* Pin 2 */ 390 #define SSB_SPROM8_GPIOB_P3 0xFF00 /* Pin 3 */ 391 #define SSB_SPROM8_GPIOB_P3_SHIFT 8 392 #define SSB_SPROM8_ANTAVAIL 0x009C /* Antenna available bitfields*/ 393 #define SSB_SPROM8_ANTAVAIL_A 0xFF00 /* A-PHY bitfield */ 394 #define SSB_SPROM8_ANTAVAIL_A_SHIFT 8 395 #define SSB_SPROM8_ANTAVAIL_BG 0x00FF /* B-PHY and G-PHY bitfield */ 396 #define SSB_SPROM8_ANTAVAIL_BG_SHIFT 0 397 #define SSB_SPROM8_AGAIN01 0x009E /* Antenna Gain (in dBm Q5.2) */ 398 #define SSB_SPROM8_AGAIN0 0x00FF /* Antenna 0 */ 399 #define SSB_SPROM8_AGAIN0_SHIFT 0 400 #define SSB_SPROM8_AGAIN1 0xFF00 /* Antenna 1 */ 401 #define SSB_SPROM8_AGAIN1_SHIFT 8 402 #define SSB_SPROM8_AGAIN23 0x00A0 403 #define SSB_SPROM8_AGAIN2 0x00FF /* Antenna 2 */ 404 #define SSB_SPROM8_AGAIN2_SHIFT 0 405 #define SSB_SPROM8_AGAIN3 0xFF00 /* Antenna 3 */ 406 #define SSB_SPROM8_AGAIN3_SHIFT 8 407 #define SSB_SPROM8_RSSIPARM2G 0x00A4 /* RSSI params for 2GHz */ 408 #define SSB_SPROM8_RSSISMF2G 0x000F 409 #define SSB_SPROM8_RSSISMC2G 0x00F0 410 #define SSB_SPROM8_RSSISMC2G_SHIFT 4 411 #define SSB_SPROM8_RSSISAV2G 0x0700 412 #define SSB_SPROM8_RSSISAV2G_SHIFT 8 413 #define SSB_SPROM8_BXA2G 0x1800 414 #define SSB_SPROM8_BXA2G_SHIFT 11 415 #define SSB_SPROM8_RSSIPARM5G 0x00A6 /* RSSI params for 5GHz */ 416 #define SSB_SPROM8_RSSISMF5G 0x000F 417 #define SSB_SPROM8_RSSISMC5G 0x00F0 418 #define SSB_SPROM8_RSSISMC5G_SHIFT 4 419 #define SSB_SPROM8_RSSISAV5G 0x0700 420 #define SSB_SPROM8_RSSISAV5G_SHIFT 8 421 #define SSB_SPROM8_BXA5G 0x1800 422 #define SSB_SPROM8_BXA5G_SHIFT 11 423 #define SSB_SPROM8_TRI25G 0x00A8 /* TX isolation 2.4&5.3GHz */ 424 #define SSB_SPROM8_TRI2G 0x00FF /* TX isolation 2.4GHz */ 425 #define SSB_SPROM8_TRI5G 0xFF00 /* TX isolation 5.3GHz */ 426 #define SSB_SPROM8_TRI5G_SHIFT 8 427 #define SSB_SPROM8_TRI5GHL 0x00AA /* TX isolation 5.2/5.8GHz */ 428 #define SSB_SPROM8_TRI5GL 0x00FF /* TX isolation 5.2GHz */ 429 #define SSB_SPROM8_TRI5GH 0xFF00 /* TX isolation 5.8GHz */ 430 #define SSB_SPROM8_TRI5GH_SHIFT 8 431 #define SSB_SPROM8_RXPO 0x00AC /* RX power offsets */ 432 #define SSB_SPROM8_RXPO2G 0x00FF /* 2GHz RX power offset */ 433 #define SSB_SPROM8_RXPO5G 0xFF00 /* 5GHz RX power offset */ 434 #define SSB_SPROM8_RXPO5G_SHIFT 8 435 #define SSB_SPROM8_MAXP_BG 0x00C0 /* Max Power 2GHz in path 1 */ 436 #define SSB_SPROM8_MAXP_BG_MASK 0x00FF /* Mask for Max Power 2GHz */ 437 #define SSB_SPROM8_ITSSI_BG 0xFF00 /* Mask for path 1 itssi_bg */ 438 #define SSB_SPROM8_ITSSI_BG_SHIFT 8 439 #define SSB_SPROM8_PA0B0 0x00C2 /* 2GHz power amp settings */ 440 #define SSB_SPROM8_PA0B1 0x00C4 441 #define SSB_SPROM8_PA0B2 0x00C6 442 #define SSB_SPROM8_MAXP_A 0x00C8 /* Max Power 5.3GHz */ 443 #define SSB_SPROM8_MAXP_A_MASK 0x00FF /* Mask for Max Power 5.3GHz */ 444 #define SSB_SPROM8_ITSSI_A 0xFF00 /* Mask for path 1 itssi_a */ 445 #define SSB_SPROM8_ITSSI_A_SHIFT 8 446 #define SSB_SPROM8_MAXP_AHL 0x00CA /* Max Power 5.2/5.8GHz */ 447 #define SSB_SPROM8_MAXP_AH_MASK 0x00FF /* Mask for Max Power 5.8GHz */ 448 #define SSB_SPROM8_MAXP_AL_MASK 0xFF00 /* Mask for Max Power 5.2GHz */ 449 #define SSB_SPROM8_MAXP_AL_SHIFT 8 450 #define SSB_SPROM8_PA1B0 0x00CC /* 5.3GHz power amp settings */ 451 #define SSB_SPROM8_PA1B1 0x00CE 452 #define SSB_SPROM8_PA1B2 0x00D0 453 #define SSB_SPROM8_PA1LOB0 0x00D2 /* 5.2GHz power amp settings */ 454 #define SSB_SPROM8_PA1LOB1 0x00D4 455 #define SSB_SPROM8_PA1LOB2 0x00D6 456 #define SSB_SPROM8_PA1HIB0 0x00D8 /* 5.8GHz power amp settings */ 457 #define SSB_SPROM8_PA1HIB1 0x00DA 458 #define SSB_SPROM8_PA1HIB2 0x00DC 459 #define SSB_SPROM8_CCK2GPO 0x0140 /* CCK power offset */ 460 #define SSB_SPROM8_OFDM2GPO 0x0142 /* 2.4GHz OFDM power offset */ 461 #define SSB_SPROM8_OFDM5GPO 0x0146 /* 5.3GHz OFDM power offset */ 462 #define SSB_SPROM8_OFDM5GLPO 0x014A /* 5.2GHz OFDM power offset */ 463 #define SSB_SPROM8_OFDM5GHPO 0x014E /* 5.8GHz OFDM power offset */ 464 465 /* Values for SSB_SPROM1_BINF_CCODE */ 466 enum { 467 SSB_SPROM1CCODE_WORLD = 0, 468 SSB_SPROM1CCODE_THAILAND, 469 SSB_SPROM1CCODE_ISRAEL, 470 SSB_SPROM1CCODE_JORDAN, 471 SSB_SPROM1CCODE_CHINA, 472 SSB_SPROM1CCODE_JAPAN, 473 SSB_SPROM1CCODE_USA_CANADA_ANZ, 474 SSB_SPROM1CCODE_EUROPE, 475 SSB_SPROM1CCODE_USA_LOW, 476 SSB_SPROM1CCODE_JAPAN_HIGH, 477 SSB_SPROM1CCODE_ALL, 478 SSB_SPROM1CCODE_NONE, 479 }; 480 481 /* Address-Match values and masks (SSB_ADMATCHxxx) */ 482 #define SSB_ADM_TYPE 0x00000003 /* Address type */ 483 #define SSB_ADM_TYPE0 0 484 #define SSB_ADM_TYPE1 1 485 #define SSB_ADM_TYPE2 2 486 #define SSB_ADM_AD64 0x00000004 487 #define SSB_ADM_SZ0 0x000000F8 /* Type0 size */ 488 #define SSB_ADM_SZ0_SHIFT 3 489 #define SSB_ADM_SZ1 0x000001F8 /* Type1 size */ 490 #define SSB_ADM_SZ1_SHIFT 3 491 #define SSB_ADM_SZ2 0x000001F8 /* Type2 size */ 492 #define SSB_ADM_SZ2_SHIFT 3 493 #define SSB_ADM_EN 0x00000400 /* Enable */ 494 #define SSB_ADM_NEG 0x00000800 /* Negative decode */ 495 #define SSB_ADM_BASE0 0xFFFFFF00 /* Type0 base address */ 496 #define SSB_ADM_BASE0_SHIFT 8 497 #define SSB_ADM_BASE1 0xFFFFF000 /* Type1 base address for the core */ 498 #define SSB_ADM_BASE1_SHIFT 12 499 #define SSB_ADM_BASE2 0xFFFF0000 /* Type2 base address for the core */ 500 #define SSB_ADM_BASE2_SHIFT 16 501 502 503 #endif /* LINUX_SSB_REGS_H_ */ 504