1 #ifndef _SCSI_LOGGING_H
2 #define _SCSI_LOGGING_H
3 
4 
5 /*
6  * This defines the scsi logging feature.  It is a means by which the user
7  * can select how much information they get about various goings on, and it
8  * can be really useful for fault tracing.  The logging word is divided into
9  * 8 nibbles, each of which describes a loglevel.  The division of things is
10  * somewhat arbitrary, and the division of the word could be changed if it
11  * were really needed for any reason.  The numbers below are the only place
12  * where these are specified.  For a first go-around, 3 bits is more than
13  * enough, since this gives 8 levels of logging (really 7, since 0 is always
14  * off).  Cutting to 2 bits might be wise at some point.
15  */
16 
17 #define SCSI_LOG_ERROR_SHIFT              0
18 #define SCSI_LOG_TIMEOUT_SHIFT            3
19 #define SCSI_LOG_SCAN_SHIFT               6
20 #define SCSI_LOG_MLQUEUE_SHIFT            9
21 #define SCSI_LOG_MLCOMPLETE_SHIFT         12
22 #define SCSI_LOG_LLQUEUE_SHIFT            15
23 #define SCSI_LOG_LLCOMPLETE_SHIFT         18
24 #define SCSI_LOG_HLQUEUE_SHIFT            21
25 #define SCSI_LOG_HLCOMPLETE_SHIFT         24
26 #define SCSI_LOG_IOCTL_SHIFT              27
27 
28 #define SCSI_LOG_ERROR_BITS               3
29 #define SCSI_LOG_TIMEOUT_BITS             3
30 #define SCSI_LOG_SCAN_BITS                3
31 #define SCSI_LOG_MLQUEUE_BITS             3
32 #define SCSI_LOG_MLCOMPLETE_BITS          3
33 #define SCSI_LOG_LLQUEUE_BITS             3
34 #define SCSI_LOG_LLCOMPLETE_BITS          3
35 #define SCSI_LOG_HLQUEUE_BITS             3
36 #define SCSI_LOG_HLCOMPLETE_BITS          3
37 #define SCSI_LOG_IOCTL_BITS               3
38 
39 extern unsigned int scsi_logging_level;
40 
41 #ifdef CONFIG_SCSI_LOGGING
42 
43 #define SCSI_LOG_LEVEL(SHIFT, BITS)				\
44         ((scsi_logging_level >> (SHIFT)) & ((1 << (BITS)) - 1))
45 
46 #define SCSI_CHECK_LOGGING(SHIFT, BITS, LEVEL, CMD)		\
47 do {								\
48         if (unlikely((SCSI_LOG_LEVEL(SHIFT, BITS)) > (LEVEL)))	\
49 		do {						\
50 			CMD;					\
51 		} while (0);					\
52 } while (0)
53 #else
54 #define SCSI_CHECK_LOGGING(SHIFT, BITS, LEVEL, CMD)
55 #endif /* CONFIG_SCSI_LOGGING */
56 
57 /*
58  * These are the macros that are actually used throughout the code to
59  * log events.  If logging isn't enabled, they are no-ops and will be
60  * completely absent from the user's code.
61  */
62 #define SCSI_LOG_ERROR_RECOVERY(LEVEL,CMD)  \
63         SCSI_CHECK_LOGGING(SCSI_LOG_ERROR_SHIFT, SCSI_LOG_ERROR_BITS, LEVEL,CMD);
64 #define SCSI_LOG_TIMEOUT(LEVEL,CMD)  \
65         SCSI_CHECK_LOGGING(SCSI_LOG_TIMEOUT_SHIFT, SCSI_LOG_TIMEOUT_BITS, LEVEL,CMD);
66 #define SCSI_LOG_SCAN_BUS(LEVEL,CMD)  \
67         SCSI_CHECK_LOGGING(SCSI_LOG_SCAN_SHIFT, SCSI_LOG_SCAN_BITS, LEVEL,CMD);
68 #define SCSI_LOG_MLQUEUE(LEVEL,CMD)  \
69         SCSI_CHECK_LOGGING(SCSI_LOG_MLQUEUE_SHIFT, SCSI_LOG_MLQUEUE_BITS, LEVEL,CMD);
70 #define SCSI_LOG_MLCOMPLETE(LEVEL,CMD)  \
71         SCSI_CHECK_LOGGING(SCSI_LOG_MLCOMPLETE_SHIFT, SCSI_LOG_MLCOMPLETE_BITS, LEVEL,CMD);
72 #define SCSI_LOG_LLQUEUE(LEVEL,CMD)  \
73         SCSI_CHECK_LOGGING(SCSI_LOG_LLQUEUE_SHIFT, SCSI_LOG_LLQUEUE_BITS, LEVEL,CMD);
74 #define SCSI_LOG_LLCOMPLETE(LEVEL,CMD)  \
75         SCSI_CHECK_LOGGING(SCSI_LOG_LLCOMPLETE_SHIFT, SCSI_LOG_LLCOMPLETE_BITS, LEVEL,CMD);
76 #define SCSI_LOG_HLQUEUE(LEVEL,CMD)  \
77         SCSI_CHECK_LOGGING(SCSI_LOG_HLQUEUE_SHIFT, SCSI_LOG_HLQUEUE_BITS, LEVEL,CMD);
78 #define SCSI_LOG_HLCOMPLETE(LEVEL,CMD)  \
79         SCSI_CHECK_LOGGING(SCSI_LOG_HLCOMPLETE_SHIFT, SCSI_LOG_HLCOMPLETE_BITS, LEVEL,CMD);
80 #define SCSI_LOG_IOCTL(LEVEL,CMD)  \
81         SCSI_CHECK_LOGGING(SCSI_LOG_IOCTL_SHIFT, SCSI_LOG_IOCTL_BITS, LEVEL,CMD);
82 
83 #endif /* _SCSI_LOGGING_H */
84