1 /* SPDX-License-Identifier: GPL-2.0-only */
2 /*
3 * Interface the generic pinconfig portions of the pinctrl subsystem
4 *
5 * Copyright (C) 2011 ST-Ericsson SA
6 * Written on behalf of Linaro for ST-Ericsson
7 * This interface is used in the core to keep track of pins.
8 *
9 * Author: Linus Walleij <linus.walleij@linaro.org>
10 */
11 #ifndef __LINUX_PINCTRL_PINCONF_GENERIC_H
12 #define __LINUX_PINCTRL_PINCONF_GENERIC_H
13
14 #include <linux/device.h>
15 #include <linux/pinctrl/machine.h>
16
17 struct pinctrl_dev;
18 struct pinctrl_map;
19
20 /**
21 * enum pin_config_param - possible pin configuration parameters
22 * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it
23 * weakly drives the last value on a tristate bus, also known as a "bus
24 * holder", "bus keeper" or "repeater". This allows another device on the
25 * bus to change the value by driving the bus high or low and switching to
26 * tristate. The argument is ignored.
27 * @PIN_CONFIG_BIAS_DISABLE: disable any pin bias on the pin, a
28 * transition from say pull-up to pull-down implies that you disable
29 * pull-up in the process, this setting disables all biasing.
30 * @PIN_CONFIG_BIAS_HIGH_IMPEDANCE: the pin will be set to a high impedance
31 * mode, also know as "third-state" (tristate) or "high-Z" or "floating".
32 * On output pins this effectively disconnects the pin, which is useful
33 * if for example some other pin is going to drive the signal connected
34 * to it for a while. Pins used for input are usually always high
35 * impedance.
36 * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high
37 * impedance to GROUND). If the argument is != 0 pull-down is enabled,
38 * if it is 0, pull-down is total, i.e. the pin is connected to GROUND.
39 * @PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: the pin will be pulled up or down based
40 * on embedded knowledge of the controller hardware, like current mux
41 * function. The pull direction and possibly strength too will normally
42 * be decided completely inside the hardware block and not be readable
43 * from the kernel side.
44 * If the argument is != 0 pull up/down is enabled, if it is 0, the
45 * configuration is ignored. The proper way to disable it is to use
46 * @PIN_CONFIG_BIAS_DISABLE.
47 * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
48 * impedance to VDD). If the argument is != 0 pull-up is enabled,
49 * if it is 0, pull-up is total, i.e. the pin is connected to VDD.
50 * @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open
51 * collector) which means it is usually wired with other output ports
52 * which are then pulled up with an external resistor. Setting this
53 * config will enable open drain mode, the argument is ignored.
54 * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source
55 * (open emitter). Setting this config will enable open source mode, the
56 * argument is ignored.
57 * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and
58 * low, this is the most typical case and is typically achieved with two
59 * active transistors on the output. Setting this config will enable
60 * push-pull mode, the argument is ignored.
61 * @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current
62 * passed as argument. The argument is in mA.
63 * @PIN_CONFIG_DRIVE_STRENGTH_UA: the pin will sink or source at most the current
64 * passed as argument. The argument is in uA.
65 * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode,
66 * which means it will wait for signals to settle when reading inputs. The
67 * argument gives the debounce time in usecs. Setting the
68 * argument to zero turns debouncing off.
69 * @PIN_CONFIG_INPUT_ENABLE: enable the pin's input. Note that this does not
70 * affect the pin's ability to drive output. 1 enables input, 0 disables
71 * input.
72 * @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in
73 * schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis,
74 * the threshold value is given on a custom format as argument when
75 * setting pins to this mode.
76 * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin.
77 * If the argument != 0, schmitt-trigger mode is enabled. If it's 0,
78 * schmitt-trigger mode is disabled.
79 * @PIN_CONFIG_MODE_LOW_POWER: this will configure the pin for low power
80 * operation, if several modes of operation are supported these can be
81 * passed in the argument on a custom form, else just use argument 1
82 * to indicate low power mode, argument 0 turns low power mode off.
83 * @PIN_CONFIG_MODE_PWM: this will configure the pin for PWM
84 * @PIN_CONFIG_OUTPUT: this will configure the pin as an output and drive a
85 * value on the line. Use argument 1 to indicate high level, argument 0 to
86 * indicate low level. (Please see Documentation/driver-api/pin-control.rst,
87 * section "GPIO mode pitfalls" for a discussion around this parameter.)
88 * @PIN_CONFIG_OUTPUT_ENABLE: this will enable the pin's output mode
89 * without driving a value there. For most platforms this reduces to
90 * enable the output buffers and then let the pin controller current
91 * configuration (eg. the currently selected mux function) drive values on
92 * the line. Use argument 1 to enable output mode, argument 0 to disable
93 * it.
94 * @PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS: this will configure the output impedance
95 * of the pin with the value passed as argument. The argument is in ohms.
96 * @PIN_CONFIG_PERSIST_STATE: retain pin state across sleep or controller reset
97 * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
98 * supplies, the argument to this parameter (on a custom format) tells
99 * the driver which alternative power source to use.
100 * @PIN_CONFIG_SKEW_DELAY: if the pin has programmable skew rate (on inputs)
101 * or latch delay (on outputs) this parameter (in a custom format)
102 * specifies the clock skew or latch delay. It typically controls how
103 * many double inverters are put in front of the line.
104 * @PIN_CONFIG_SLEEP_HARDWARE_STATE: indicate this is sleep related state.
105 * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
106 * this parameter (on a custom format) tells the driver which alternative
107 * slew rate to use.
108 * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if
109 * you need to pass in custom configurations to the pin controller, use
110 * PIN_CONFIG_END+1 as the base offset.
111 * @PIN_CONFIG_MAX: this is the maximum configuration value that can be
112 * presented using the packed format.
113 */
114 enum pin_config_param {
115 PIN_CONFIG_BIAS_BUS_HOLD,
116 PIN_CONFIG_BIAS_DISABLE,
117 PIN_CONFIG_BIAS_HIGH_IMPEDANCE,
118 PIN_CONFIG_BIAS_PULL_DOWN,
119 PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
120 PIN_CONFIG_BIAS_PULL_UP,
121 PIN_CONFIG_DRIVE_OPEN_DRAIN,
122 PIN_CONFIG_DRIVE_OPEN_SOURCE,
123 PIN_CONFIG_DRIVE_PUSH_PULL,
124 PIN_CONFIG_DRIVE_STRENGTH,
125 PIN_CONFIG_DRIVE_STRENGTH_UA,
126 PIN_CONFIG_INPUT_DEBOUNCE,
127 PIN_CONFIG_INPUT_ENABLE,
128 PIN_CONFIG_INPUT_SCHMITT,
129 PIN_CONFIG_INPUT_SCHMITT_ENABLE,
130 PIN_CONFIG_MODE_LOW_POWER,
131 PIN_CONFIG_MODE_PWM,
132 PIN_CONFIG_OUTPUT,
133 PIN_CONFIG_OUTPUT_ENABLE,
134 PIN_CONFIG_OUTPUT_IMPEDANCE_OHMS,
135 PIN_CONFIG_PERSIST_STATE,
136 PIN_CONFIG_POWER_SOURCE,
137 PIN_CONFIG_SKEW_DELAY,
138 PIN_CONFIG_SLEEP_HARDWARE_STATE,
139 PIN_CONFIG_SLEW_RATE,
140 PIN_CONFIG_END = 0x7F,
141 PIN_CONFIG_MAX = 0xFF,
142 };
143
144 /*
145 * Helpful configuration macro to be used in tables etc.
146 */
147 #define PIN_CONF_PACKED(p, a) ((a << 8) | ((unsigned long) p & 0xffUL))
148
149 /*
150 * The following inlines stuffs a configuration parameter and data value
151 * into and out of an unsigned long argument, as used by the generic pin config
152 * system. We put the parameter in the lower 8 bits and the argument in the
153 * upper 24 bits.
154 */
155
pinconf_to_config_param(unsigned long config)156 static inline enum pin_config_param pinconf_to_config_param(unsigned long config)
157 {
158 return (enum pin_config_param) (config & 0xffUL);
159 }
160
pinconf_to_config_argument(unsigned long config)161 static inline u32 pinconf_to_config_argument(unsigned long config)
162 {
163 return (u32) ((config >> 8) & 0xffffffUL);
164 }
165
pinconf_to_config_packed(enum pin_config_param param,u32 argument)166 static inline unsigned long pinconf_to_config_packed(enum pin_config_param param,
167 u32 argument)
168 {
169 return PIN_CONF_PACKED(param, argument);
170 }
171
172 #define PCONFDUMP(a, b, c, d) { \
173 .param = a, .display = b, .format = c, .has_arg = d \
174 }
175
176 struct pin_config_item {
177 const enum pin_config_param param;
178 const char * const display;
179 const char * const format;
180 bool has_arg;
181 };
182
183 struct pinconf_generic_params {
184 const char * const property;
185 enum pin_config_param param;
186 u32 default_value;
187 };
188
189 int pinconf_generic_dt_subnode_to_map(struct pinctrl_dev *pctldev,
190 struct device_node *np, struct pinctrl_map **map,
191 unsigned *reserved_maps, unsigned *num_maps,
192 enum pinctrl_map_type type);
193 int pinconf_generic_dt_node_to_map(struct pinctrl_dev *pctldev,
194 struct device_node *np_config, struct pinctrl_map **map,
195 unsigned *num_maps, enum pinctrl_map_type type);
196 void pinconf_generic_dt_free_map(struct pinctrl_dev *pctldev,
197 struct pinctrl_map *map, unsigned num_maps);
198
pinconf_generic_dt_node_to_map_group(struct pinctrl_dev * pctldev,struct device_node * np_config,struct pinctrl_map ** map,unsigned * num_maps)199 static inline int pinconf_generic_dt_node_to_map_group(
200 struct pinctrl_dev *pctldev, struct device_node *np_config,
201 struct pinctrl_map **map, unsigned *num_maps)
202 {
203 return pinconf_generic_dt_node_to_map(pctldev, np_config, map, num_maps,
204 PIN_MAP_TYPE_CONFIGS_GROUP);
205 }
206
pinconf_generic_dt_node_to_map_pin(struct pinctrl_dev * pctldev,struct device_node * np_config,struct pinctrl_map ** map,unsigned * num_maps)207 static inline int pinconf_generic_dt_node_to_map_pin(
208 struct pinctrl_dev *pctldev, struct device_node *np_config,
209 struct pinctrl_map **map, unsigned *num_maps)
210 {
211 return pinconf_generic_dt_node_to_map(pctldev, np_config, map, num_maps,
212 PIN_MAP_TYPE_CONFIGS_PIN);
213 }
214
pinconf_generic_dt_node_to_map_all(struct pinctrl_dev * pctldev,struct device_node * np_config,struct pinctrl_map ** map,unsigned * num_maps)215 static inline int pinconf_generic_dt_node_to_map_all(
216 struct pinctrl_dev *pctldev, struct device_node *np_config,
217 struct pinctrl_map **map, unsigned *num_maps)
218 {
219 /*
220 * passing the type as PIN_MAP_TYPE_INVALID causes the underlying parser
221 * to infer the map type from the DT properties used.
222 */
223 return pinconf_generic_dt_node_to_map(pctldev, np_config, map, num_maps,
224 PIN_MAP_TYPE_INVALID);
225 }
226
227 #endif /* __LINUX_PINCTRL_PINCONF_GENERIC_H */
228