1 /* 2 * linux/mtio.h header file for Linux. Written by H. Bergman 3 * 4 * Modified for special ioctls provided by zftape in September 1997 5 * by C.-J. Heine. 6 */ 7 8 #ifndef _LINUX_MTIO_H 9 #define _LINUX_MTIO_H 10 11 #include <linux/types.h> 12 #include <linux/ioctl.h> 13 14 /* 15 * Structures and definitions for mag tape io control commands 16 */ 17 18 /* structure for MTIOCTOP - mag tape op command */ 19 struct mtop { 20 short mt_op; /* operations defined below */ 21 int mt_count; /* how many of them */ 22 }; 23 24 /* Magnetic Tape operations [Not all operations supported by all drivers]: */ 25 #define MTRESET 0 /* +reset drive in case of problems */ 26 #define MTFSF 1 /* forward space over FileMark, 27 * position at first record of next file 28 */ 29 #define MTBSF 2 /* backward space FileMark (position before FM) */ 30 #define MTFSR 3 /* forward space record */ 31 #define MTBSR 4 /* backward space record */ 32 #define MTWEOF 5 /* write an end-of-file record (mark) */ 33 #define MTREW 6 /* rewind */ 34 #define MTOFFL 7 /* rewind and put the drive offline (eject?) */ 35 #define MTNOP 8 /* no op, set status only (read with MTIOCGET) */ 36 #define MTRETEN 9 /* retension tape */ 37 #define MTBSFM 10 /* +backward space FileMark, position at FM */ 38 #define MTFSFM 11 /* +forward space FileMark, position at FM */ 39 #define MTEOM 12 /* goto end of recorded media (for appending files). 40 * MTEOM positions after the last FM, ready for 41 * appending another file. 42 */ 43 #define MTERASE 13 /* erase tape -- be careful! */ 44 45 #define MTRAS1 14 /* run self test 1 (nondestructive) */ 46 #define MTRAS2 15 /* run self test 2 (destructive) */ 47 #define MTRAS3 16 /* reserved for self test 3 */ 48 49 #define MTSETBLK 20 /* set block length (SCSI) */ 50 #define MTSETDENSITY 21 /* set tape density (SCSI) */ 51 #define MTSEEK 22 /* seek to block (Tandberg, etc.) */ 52 #define MTTELL 23 /* tell block (Tandberg, etc.) */ 53 #define MTSETDRVBUFFER 24 /* set the drive buffering according to SCSI-2 */ 54 /* ordinary buffered operation with code 1 */ 55 #define MTFSS 25 /* space forward over setmarks */ 56 #define MTBSS 26 /* space backward over setmarks */ 57 #define MTWSM 27 /* write setmarks */ 58 59 #define MTLOCK 28 /* lock the drive door */ 60 #define MTUNLOCK 29 /* unlock the drive door */ 61 #define MTLOAD 30 /* execute the SCSI load command */ 62 #define MTUNLOAD 31 /* execute the SCSI unload command */ 63 #define MTCOMPRESSION 32/* control compression with SCSI mode page 15 */ 64 #define MTSETPART 33 /* Change the active tape partition */ 65 #define MTMKPART 34 /* Format the tape with one or two partitions */ 66 #define MTWEOFI 35 /* write an end-of-file record (mark) in immediate mode */ 67 68 /* structure for MTIOCGET - mag tape get status command */ 69 70 struct mtget { 71 long mt_type; /* type of magtape device */ 72 long mt_resid; /* residual count: (not sure) 73 * number of bytes ignored, or 74 * number of files not skipped, or 75 * number of records not skipped. 76 */ 77 /* the following registers are device dependent */ 78 long mt_dsreg; /* status register */ 79 long mt_gstat; /* generic (device independent) status */ 80 long mt_erreg; /* error register */ 81 /* The next two fields are not always used */ 82 __kernel_daddr_t mt_fileno; /* number of current file on tape */ 83 __kernel_daddr_t mt_blkno; /* current block number */ 84 }; 85 86 87 88 /* 89 * Constants for mt_type. Not all of these are supported, 90 * and these are not all of the ones that are supported. 91 */ 92 #define MT_ISUNKNOWN 0x01 93 #define MT_ISQIC02 0x02 /* Generic QIC-02 tape streamer */ 94 #define MT_ISWT5150 0x03 /* Wangtek 5150EQ, QIC-150, QIC-02 */ 95 #define MT_ISARCHIVE_5945L2 0x04 /* Archive 5945L-2, QIC-24, QIC-02? */ 96 #define MT_ISCMSJ500 0x05 /* CMS Jumbo 500 (QIC-02?) */ 97 #define MT_ISTDC3610 0x06 /* Tandberg 6310, QIC-24 */ 98 #define MT_ISARCHIVE_VP60I 0x07 /* Archive VP60i, QIC-02 */ 99 #define MT_ISARCHIVE_2150L 0x08 /* Archive Viper 2150L */ 100 #define MT_ISARCHIVE_2060L 0x09 /* Archive Viper 2060L */ 101 #define MT_ISARCHIVESC499 0x0A /* Archive SC-499 QIC-36 controller */ 102 #define MT_ISQIC02_ALL_FEATURES 0x0F /* Generic QIC-02 with all features */ 103 #define MT_ISWT5099EEN24 0x11 /* Wangtek 5099-een24, 60MB, QIC-24 */ 104 #define MT_ISTEAC_MT2ST 0x12 /* Teac MT-2ST 155mb drive, Teac DC-1 card (Wangtek type) */ 105 #define MT_ISEVEREX_FT40A 0x32 /* Everex FT40A (QIC-40) */ 106 #define MT_ISDDS1 0x51 /* DDS device without partitions */ 107 #define MT_ISDDS2 0x52 /* DDS device with partitions */ 108 #define MT_ISONSTREAM_SC 0x61 /* OnStream SCSI tape drives (SC-x0) 109 and SCSI emulated (DI, DP, USB) */ 110 #define MT_ISSCSI1 0x71 /* Generic ANSI SCSI-1 tape unit */ 111 #define MT_ISSCSI2 0x72 /* Generic ANSI SCSI-2 tape unit */ 112 113 /* QIC-40/80/3010/3020 ftape supported drives. 114 * 20bit vendor ID + 0x800000 (see ftape-vendors.h) 115 */ 116 #define MT_ISFTAPE_UNKNOWN 0x800000 /* obsolete */ 117 #define MT_ISFTAPE_FLAG 0x800000 118 119 120 /* structure for MTIOCPOS - mag tape get position command */ 121 122 struct mtpos { 123 long mt_blkno; /* current block number */ 124 }; 125 126 127 /* mag tape io control commands */ 128 #define MTIOCTOP _IOW('m', 1, struct mtop) /* do a mag tape op */ 129 #define MTIOCGET _IOR('m', 2, struct mtget) /* get tape status */ 130 #define MTIOCPOS _IOR('m', 3, struct mtpos) /* get tape position */ 131 132 133 /* Generic Mag Tape (device independent) status macros for examining 134 * mt_gstat -- HP-UX compatible. 135 * There is room for more generic status bits here, but I don't 136 * know which of them are reserved. At least three or so should 137 * be added to make this really useful. 138 */ 139 #define GMT_EOF(x) ((x) & 0x80000000) 140 #define GMT_BOT(x) ((x) & 0x40000000) 141 #define GMT_EOT(x) ((x) & 0x20000000) 142 #define GMT_SM(x) ((x) & 0x10000000) /* DDS setmark */ 143 #define GMT_EOD(x) ((x) & 0x08000000) /* DDS EOD */ 144 #define GMT_WR_PROT(x) ((x) & 0x04000000) 145 /* #define GMT_ ? ((x) & 0x02000000) */ 146 #define GMT_ONLINE(x) ((x) & 0x01000000) 147 #define GMT_D_6250(x) ((x) & 0x00800000) 148 #define GMT_D_1600(x) ((x) & 0x00400000) 149 #define GMT_D_800(x) ((x) & 0x00200000) 150 /* #define GMT_ ? ((x) & 0x00100000) */ 151 /* #define GMT_ ? ((x) & 0x00080000) */ 152 #define GMT_DR_OPEN(x) ((x) & 0x00040000) /* door open (no tape) */ 153 /* #define GMT_ ? ((x) & 0x00020000) */ 154 #define GMT_IM_REP_EN(x) ((x) & 0x00010000) /* immediate report mode */ 155 #define GMT_CLN(x) ((x) & 0x00008000) /* cleaning requested */ 156 /* 15 generic status bits unused */ 157 158 159 /* SCSI-tape specific definitions */ 160 /* Bitfield shifts in the status */ 161 #define MT_ST_BLKSIZE_SHIFT 0 162 #define MT_ST_BLKSIZE_MASK 0xffffff 163 #define MT_ST_DENSITY_SHIFT 24 164 #define MT_ST_DENSITY_MASK 0xff000000 165 166 #define MT_ST_SOFTERR_SHIFT 0 167 #define MT_ST_SOFTERR_MASK 0xffff 168 169 /* Bitfields for the MTSETDRVBUFFER ioctl */ 170 #define MT_ST_OPTIONS 0xf0000000 171 #define MT_ST_BOOLEANS 0x10000000 172 #define MT_ST_SETBOOLEANS 0x30000000 173 #define MT_ST_CLEARBOOLEANS 0x40000000 174 #define MT_ST_WRITE_THRESHOLD 0x20000000 175 #define MT_ST_DEF_BLKSIZE 0x50000000 176 #define MT_ST_DEF_OPTIONS 0x60000000 177 #define MT_ST_TIMEOUTS 0x70000000 178 #define MT_ST_SET_TIMEOUT (MT_ST_TIMEOUTS | 0x000000) 179 #define MT_ST_SET_LONG_TIMEOUT (MT_ST_TIMEOUTS | 0x100000) 180 #define MT_ST_SET_CLN 0x80000000 181 182 #define MT_ST_BUFFER_WRITES 0x1 183 #define MT_ST_ASYNC_WRITES 0x2 184 #define MT_ST_READ_AHEAD 0x4 185 #define MT_ST_DEBUGGING 0x8 186 #define MT_ST_TWO_FM 0x10 187 #define MT_ST_FAST_MTEOM 0x20 188 #define MT_ST_AUTO_LOCK 0x40 189 #define MT_ST_DEF_WRITES 0x80 190 #define MT_ST_CAN_BSR 0x100 191 #define MT_ST_NO_BLKLIMS 0x200 192 #define MT_ST_CAN_PARTITIONS 0x400 193 #define MT_ST_SCSI2LOGICAL 0x800 194 #define MT_ST_SYSV 0x1000 195 #define MT_ST_NOWAIT 0x2000 196 #define MT_ST_SILI 0x4000 197 198 /* The mode parameters to be controlled. Parameter chosen with bits 20-28 */ 199 #define MT_ST_CLEAR_DEFAULT 0xfffff 200 #define MT_ST_DEF_DENSITY (MT_ST_DEF_OPTIONS | 0x100000) 201 #define MT_ST_DEF_COMPRESSION (MT_ST_DEF_OPTIONS | 0x200000) 202 #define MT_ST_DEF_DRVBUFFER (MT_ST_DEF_OPTIONS | 0x300000) 203 204 /* The offset for the arguments for the special HP changer load command. */ 205 #define MT_ST_HPLOADER_OFFSET 10000 206 207 #endif /* _LINUX_MTIO_H */ 208