1 /* 2 * Definitions for the KLSI KL5KUSB105 serial port adapter 3 */ 4 5 /* vendor/product pairs that are known to contain this chipset */ 6 #define PALMCONNECT_VID 0x0830 7 #define PALMCONNECT_PID 0x0080 8 9 #define KLSI_VID 0x05e9 10 #define KLSI_KL5KUSB105D_PID 0x00c0 11 12 /* Vendor commands: */ 13 14 15 /* port table -- the chip supports up to 4 channels */ 16 17 /* baud rates */ 18 19 enum { 20 kl5kusb105a_sio_b115200 = 0, 21 kl5kusb105a_sio_b57600 = 1, 22 kl5kusb105a_sio_b38400 = 2, 23 kl5kusb105a_sio_b19200 = 4, 24 kl5kusb105a_sio_b14400 = 5, 25 kl5kusb105a_sio_b9600 = 6, 26 kl5kusb105a_sio_b4800 = 8, /* unchecked */ 27 kl5kusb105a_sio_b2400 = 9, /* unchecked */ 28 kl5kusb105a_sio_b1200 = 0xa, /* unchecked */ 29 kl5kusb105a_sio_b600 = 0xb /* unchecked */ 30 }; 31 32 /* data bits */ 33 #define kl5kusb105a_dtb_7 7 34 #define kl5kusb105a_dtb_8 8 35 36 37 38 /* requests: */ 39 #define KL5KUSB105A_SIO_SET_DATA 1 40 #define KL5KUSB105A_SIO_POLL 2 41 #define KL5KUSB105A_SIO_CONFIGURE 3 42 /* values used for request KL5KUSB105A_SIO_CONFIGURE */ 43 #define KL5KUSB105A_SIO_CONFIGURE_READ_ON 3 44 #define KL5KUSB105A_SIO_CONFIGURE_READ_OFF 2 45 46 /* Interpretation of modem status lines */ 47 /* These need sorting out by individually connecting pins and checking 48 * results. FIXME! 49 * When data is being sent we see 0x30 in the lower byte; this must 50 * contain DSR and CTS ... 51 */ 52 #define KL5KUSB105A_DSR ((1<<4) | (1<<5)) 53 #define KL5KUSB105A_CTS ((1<<5) | (1<<4)) 54 55 #define KL5KUSB105A_WANTS_TO_SEND 0x30 56 //#define KL5KUSB105A_DTR /* Data Terminal Ready */ 57 //#define KL5KUSB105A_CTS /* Clear To Send */ 58 //#define KL5KUSB105A_CD /* Carrier Detect */ 59 //#define KL5KUSB105A_DSR /* Data Set Ready */ 60 //#define KL5KUSB105A_RxD /* Receive pin */ 61 62 //#define KL5KUSB105A_LE 63 //#define KL5KUSB105A_RTS 64 //#define KL5KUSB105A_ST 65 //#define KL5KUSB105A_SR 66 //#define KL5KUSB105A_RI /* Ring Indicator */ 67 68 /* vim: set ts=8 sts=8: */ 69 70