1 /* 2 * OMAP clock: data structure definitions, function prototypes, shared macros 3 * 4 * Copyright (C) 2004-2005, 2008-2010 Nokia Corporation 5 * Written by Tuukka Tikkanen <tuukka.tikkanen@elektrobit.com> 6 * Based on clocks.h by Tony Lindgren, Gordon McNutt and RidgeRun, Inc 7 * 8 * This program is free software; you can redistribute it and/or modify 9 * it under the terms of the GNU General Public License version 2 as 10 * published by the Free Software Foundation. 11 */ 12 13 #ifndef __ARCH_ARM_OMAP_CLOCK_H 14 #define __ARCH_ARM_OMAP_CLOCK_H 15 16 #include <linux/list.h> 17 18 struct module; 19 struct clk; 20 struct clockdomain; 21 22 /** 23 * struct clkops - some clock function pointers 24 * @enable: fn ptr that enables the current clock in hardware 25 * @disable: fn ptr that enables the current clock in hardware 26 * @find_idlest: function returning the IDLEST register for the clock's IP blk 27 * @find_companion: function returning the "companion" clk reg for the clock 28 * @allow_idle: fn ptr that enables autoidle for the current clock in hardware 29 * @deny_idle: fn ptr that disables autoidle for the current clock in hardware 30 * 31 * A "companion" clk is an accompanying clock to the one being queried 32 * that must be enabled for the IP module connected to the clock to 33 * become accessible by the hardware. Neither @find_idlest nor 34 * @find_companion should be needed; that information is IP 35 * block-specific; the hwmod code has been created to handle this, but 36 * until hwmod data is ready and drivers have been converted to use PM 37 * runtime calls in place of clk_enable()/clk_disable(), @find_idlest and 38 * @find_companion must, unfortunately, remain. 39 */ 40 struct clkops { 41 int (*enable)(struct clk *); 42 void (*disable)(struct clk *); 43 void (*find_idlest)(struct clk *, void __iomem **, 44 u8 *, u8 *); 45 void (*find_companion)(struct clk *, void __iomem **, 46 u8 *); 47 void (*allow_idle)(struct clk *); 48 void (*deny_idle)(struct clk *); 49 }; 50 51 #ifdef CONFIG_ARCH_OMAP2PLUS 52 53 /* struct clksel_rate.flags possibilities */ 54 #define RATE_IN_242X (1 << 0) 55 #define RATE_IN_243X (1 << 1) 56 #define RATE_IN_3430ES1 (1 << 2) /* 3430ES1 rates only */ 57 #define RATE_IN_3430ES2PLUS (1 << 3) /* 3430 ES >= 2 rates only */ 58 #define RATE_IN_36XX (1 << 4) 59 #define RATE_IN_4430 (1 << 5) 60 #define RATE_IN_TI816X (1 << 6) 61 62 #define RATE_IN_24XX (RATE_IN_242X | RATE_IN_243X) 63 #define RATE_IN_34XX (RATE_IN_3430ES1 | RATE_IN_3430ES2PLUS) 64 #define RATE_IN_3XXX (RATE_IN_34XX | RATE_IN_36XX) 65 66 /* RATE_IN_3430ES2PLUS_36XX includes 34xx/35xx with ES >=2, and all 36xx/37xx */ 67 #define RATE_IN_3430ES2PLUS_36XX (RATE_IN_3430ES2PLUS | RATE_IN_36XX) 68 69 70 /** 71 * struct clksel_rate - register bitfield values corresponding to clk divisors 72 * @val: register bitfield value (shifted to bit 0) 73 * @div: clock divisor corresponding to @val 74 * @flags: (see "struct clksel_rate.flags possibilities" above) 75 * 76 * @val should match the value of a read from struct clk.clksel_reg 77 * AND'ed with struct clk.clksel_mask, shifted right to bit 0. 78 * 79 * @div is the divisor that should be applied to the parent clock's rate 80 * to produce the current clock's rate. 81 * 82 * XXX @flags probably should be replaced with an struct omap_chip. 83 */ 84 struct clksel_rate { 85 u32 val; 86 u8 div; 87 u8 flags; 88 }; 89 90 /** 91 * struct clksel - available parent clocks, and a pointer to their divisors 92 * @parent: struct clk * to a possible parent clock 93 * @rates: available divisors for this parent clock 94 * 95 * A struct clksel is always associated with one or more struct clks 96 * and one or more struct clksel_rates. 97 */ 98 struct clksel { 99 struct clk *parent; 100 const struct clksel_rate *rates; 101 }; 102 103 /** 104 * struct dpll_data - DPLL registers and integration data 105 * @mult_div1_reg: register containing the DPLL M and N bitfields 106 * @mult_mask: mask of the DPLL M bitfield in @mult_div1_reg 107 * @div1_mask: mask of the DPLL N bitfield in @mult_div1_reg 108 * @clk_bypass: struct clk pointer to the clock's bypass clock input 109 * @clk_ref: struct clk pointer to the clock's reference clock input 110 * @control_reg: register containing the DPLL mode bitfield 111 * @enable_mask: mask of the DPLL mode bitfield in @control_reg 112 * @last_rounded_rate: cache of the last rate result of omap2_dpll_round_rate() 113 * @last_rounded_m: cache of the last M result of omap2_dpll_round_rate() 114 * @max_multiplier: maximum valid non-bypass multiplier value (actual) 115 * @last_rounded_n: cache of the last N result of omap2_dpll_round_rate() 116 * @min_divider: minimum valid non-bypass divider value (actual) 117 * @max_divider: maximum valid non-bypass divider value (actual) 118 * @modes: possible values of @enable_mask 119 * @autoidle_reg: register containing the DPLL autoidle mode bitfield 120 * @idlest_reg: register containing the DPLL idle status bitfield 121 * @autoidle_mask: mask of the DPLL autoidle mode bitfield in @autoidle_reg 122 * @freqsel_mask: mask of the DPLL jitter correction bitfield in @control_reg 123 * @idlest_mask: mask of the DPLL idle status bitfield in @idlest_reg 124 * @auto_recal_bit: bitshift of the driftguard enable bit in @control_reg 125 * @recal_en_bit: bitshift of the PRM_IRQENABLE_* bit for recalibration IRQs 126 * @recal_st_bit: bitshift of the PRM_IRQSTATUS_* bit for recalibration IRQs 127 * @flags: DPLL type/features (see below) 128 * 129 * Possible values for @flags: 130 * DPLL_J_TYPE: "J-type DPLL" (only some 36xx, 4xxx DPLLs) 131 * 132 * @freqsel_mask is only used on the OMAP34xx family and AM35xx. 133 * 134 * XXX Some DPLLs have multiple bypass inputs, so it's not technically 135 * correct to only have one @clk_bypass pointer. 136 * 137 * XXX The runtime-variable fields (@last_rounded_rate, @last_rounded_m, 138 * @last_rounded_n) should be separated from the runtime-fixed fields 139 * and placed into a different structure, so that the runtime-fixed data 140 * can be placed into read-only space. 141 */ 142 struct dpll_data { 143 void __iomem *mult_div1_reg; 144 u32 mult_mask; 145 u32 div1_mask; 146 struct clk *clk_bypass; 147 struct clk *clk_ref; 148 void __iomem *control_reg; 149 u32 enable_mask; 150 unsigned long last_rounded_rate; 151 u16 last_rounded_m; 152 u16 max_multiplier; 153 u8 last_rounded_n; 154 u8 min_divider; 155 u8 max_divider; 156 u8 modes; 157 #if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4) 158 void __iomem *autoidle_reg; 159 void __iomem *idlest_reg; 160 u32 autoidle_mask; 161 u32 freqsel_mask; 162 u32 idlest_mask; 163 u32 dco_mask; 164 u32 sddiv_mask; 165 u8 auto_recal_bit; 166 u8 recal_en_bit; 167 u8 recal_st_bit; 168 u8 flags; 169 # endif 170 }; 171 172 #endif 173 174 /* 175 * struct clk.flags possibilities 176 * 177 * XXX document the rest of the clock flags here 178 * 179 * CLOCK_CLKOUTX2: (OMAP4 only) DPLL CLKOUT and CLKOUTX2 GATE_CTRL 180 * bits share the same register. This flag allows the 181 * omap4_dpllmx*() code to determine which GATE_CTRL bit field 182 * should be used. This is a temporary solution - a better approach 183 * would be to associate clock type-specific data with the clock, 184 * similar to the struct dpll_data approach. 185 */ 186 #define ENABLE_REG_32BIT (1 << 0) /* Use 32-bit access */ 187 #define CLOCK_IDLE_CONTROL (1 << 1) 188 #define CLOCK_NO_IDLE_PARENT (1 << 2) 189 #define ENABLE_ON_INIT (1 << 3) /* Enable upon framework init */ 190 #define INVERT_ENABLE (1 << 4) /* 0 enables, 1 disables */ 191 #define CLOCK_CLKOUTX2 (1 << 5) 192 193 /** 194 * struct clk - OMAP struct clk 195 * @node: list_head connecting this clock into the full clock list 196 * @ops: struct clkops * for this clock 197 * @name: the name of the clock in the hardware (used in hwmod data and debug) 198 * @parent: pointer to this clock's parent struct clk 199 * @children: list_head connecting to the child clks' @sibling list_heads 200 * @sibling: list_head connecting this clk to its parent clk's @children 201 * @rate: current clock rate 202 * @enable_reg: register to write to enable the clock (see @enable_bit) 203 * @recalc: fn ptr that returns the clock's current rate 204 * @set_rate: fn ptr that can change the clock's current rate 205 * @round_rate: fn ptr that can round the clock's current rate 206 * @init: fn ptr to do clock-specific initialization 207 * @enable_bit: bitshift to write to enable/disable the clock (see @enable_reg) 208 * @usecount: number of users that have requested this clock to be enabled 209 * @fixed_div: when > 0, this clock's rate is its parent's rate / @fixed_div 210 * @flags: see "struct clk.flags possibilities" above 211 * @clksel_reg: for clksel clks, register va containing src/divisor select 212 * @clksel_mask: bitmask in @clksel_reg for the src/divisor selector 213 * @clksel: for clksel clks, pointer to struct clksel for this clock 214 * @dpll_data: for DPLLs, pointer to struct dpll_data for this clock 215 * @clkdm_name: clockdomain name that this clock is contained in 216 * @clkdm: pointer to struct clockdomain, resolved from @clkdm_name at runtime 217 * @rate_offset: bitshift for rate selection bitfield (OMAP1 only) 218 * @src_offset: bitshift for source selection bitfield (OMAP1 only) 219 * 220 * XXX @rate_offset, @src_offset should probably be removed and OMAP1 221 * clock code converted to use clksel. 222 * 223 * XXX @usecount is poorly named. It should be "enable_count" or 224 * something similar. "users" in the description refers to kernel 225 * code (core code or drivers) that have called clk_enable() and not 226 * yet called clk_disable(); the usecount of parent clocks is also 227 * incremented by the clock code when clk_enable() is called on child 228 * clocks and decremented by the clock code when clk_disable() is 229 * called on child clocks. 230 * 231 * XXX @clkdm, @usecount, @children, @sibling should be marked for 232 * internal use only. 233 * 234 * @children and @sibling are used to optimize parent-to-child clock 235 * tree traversals. (child-to-parent traversals use @parent.) 236 * 237 * XXX The notion of the clock's current rate probably needs to be 238 * separated from the clock's target rate. 239 */ 240 struct clk { 241 struct list_head node; 242 const struct clkops *ops; 243 const char *name; 244 struct clk *parent; 245 struct list_head children; 246 struct list_head sibling; /* node for children */ 247 unsigned long rate; 248 void __iomem *enable_reg; 249 unsigned long (*recalc)(struct clk *); 250 int (*set_rate)(struct clk *, unsigned long); 251 long (*round_rate)(struct clk *, unsigned long); 252 void (*init)(struct clk *); 253 u8 enable_bit; 254 s8 usecount; 255 u8 fixed_div; 256 u8 flags; 257 #ifdef CONFIG_ARCH_OMAP2PLUS 258 void __iomem *clksel_reg; 259 u32 clksel_mask; 260 const struct clksel *clksel; 261 struct dpll_data *dpll_data; 262 const char *clkdm_name; 263 struct clockdomain *clkdm; 264 #else 265 u8 rate_offset; 266 u8 src_offset; 267 #endif 268 #if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS) 269 struct dentry *dent; /* For visible tree hierarchy */ 270 #endif 271 }; 272 273 struct cpufreq_frequency_table; 274 275 struct clk_functions { 276 int (*clk_enable)(struct clk *clk); 277 void (*clk_disable)(struct clk *clk); 278 long (*clk_round_rate)(struct clk *clk, unsigned long rate); 279 int (*clk_set_rate)(struct clk *clk, unsigned long rate); 280 int (*clk_set_parent)(struct clk *clk, struct clk *parent); 281 void (*clk_allow_idle)(struct clk *clk); 282 void (*clk_deny_idle)(struct clk *clk); 283 void (*clk_disable_unused)(struct clk *clk); 284 #ifdef CONFIG_CPU_FREQ 285 void (*clk_init_cpufreq_table)(struct cpufreq_frequency_table **); 286 void (*clk_exit_cpufreq_table)(struct cpufreq_frequency_table **); 287 #endif 288 }; 289 290 extern int mpurate; 291 292 extern int clk_init(struct clk_functions *custom_clocks); 293 extern void clk_preinit(struct clk *clk); 294 extern int clk_register(struct clk *clk); 295 extern void clk_reparent(struct clk *child, struct clk *parent); 296 extern void clk_unregister(struct clk *clk); 297 extern void propagate_rate(struct clk *clk); 298 extern void recalculate_root_clocks(void); 299 extern unsigned long followparent_recalc(struct clk *clk); 300 extern void clk_enable_init_clocks(void); 301 unsigned long omap_fixed_divisor_recalc(struct clk *clk); 302 #ifdef CONFIG_CPU_FREQ 303 extern void clk_init_cpufreq_table(struct cpufreq_frequency_table **table); 304 extern void clk_exit_cpufreq_table(struct cpufreq_frequency_table **table); 305 #endif 306 extern struct clk *omap_clk_get_by_name(const char *name); 307 extern int omap_clk_enable_autoidle_all(void); 308 extern int omap_clk_disable_autoidle_all(void); 309 310 extern const struct clkops clkops_null; 311 312 extern struct clk dummy_ck; 313 314 #endif 315