1menuconfig OMAP2_DSS
2        tristate "OMAP2+ Display Subsystem support (EXPERIMENTAL)"
3        depends on ARCH_OMAP2PLUS
4        help
5	  OMAP2+ Display Subsystem support.
6
7if OMAP2_DSS
8
9config OMAP2_VRAM_SIZE
10	int "VRAM size (MB)"
11	range 0 32
12	default 0
13	help
14	  The amount of SDRAM to reserve at boot time for video RAM use.
15	  This VRAM will be used by omapfb and other drivers that need
16	  large continuous RAM area for video use.
17
18	  You can also set this with "vram=<bytes>" kernel argument, or
19	  in the board file.
20
21config OMAP2_DSS_DEBUG_SUPPORT
22        bool "Debug support"
23	default y
24	help
25	  This enables debug messages. You need to enable printing
26	  with 'debug' module parameter.
27
28config OMAP2_DSS_COLLECT_IRQ_STATS
29	bool "Collect DSS IRQ statistics"
30	depends on OMAP2_DSS_DEBUG_SUPPORT
31	default n
32	help
33	  Collect DSS IRQ statistics, printable via debugfs.
34
35	  The statistics can be found from
36	  <debugfs>/omapdss/dispc_irq for DISPC interrupts, and
37	  <debugfs>/omapdss/dsi_irq for DSI interrupts.
38
39config OMAP2_DSS_DPI
40	bool "DPI support"
41	default y
42	help
43	  DPI Interface. This is the Parallel Display Interface.
44
45config OMAP2_DSS_RFBI
46	bool "RFBI support"
47        default n
48	help
49	  MIPI DBI support (RFBI, Remote Framebuffer Interface, in Texas
50	  Instrument's terminology).
51
52	  DBI is a bus between the host processor and a peripheral,
53	  such as a display or a framebuffer chip.
54
55	  See http://www.mipi.org/ for DBI spesifications.
56
57config OMAP2_DSS_VENC
58	bool "VENC support"
59        default y
60	help
61	  OMAP Video Encoder support for S-Video and composite TV-out.
62
63config OMAP4_DSS_HDMI
64	bool "HDMI support"
65	depends on ARCH_OMAP4
66        default y
67	help
68	  HDMI Interface. This adds the High Definition Multimedia Interface.
69	  See http://www.hdmi.org/ for HDMI specification.
70
71config OMAP2_DSS_SDI
72	bool "SDI support"
73	depends on ARCH_OMAP3
74        default n
75	help
76	  SDI (Serial Display Interface) support.
77
78	  SDI is a high speed one-way display serial bus between the host
79	  processor and a display.
80
81config OMAP2_DSS_DSI
82	bool "DSI support"
83	depends on ARCH_OMAP3
84        default n
85	help
86	  MIPI DSI (Display Serial Interface) support.
87
88	  DSI is a high speed half-duplex serial interface between the host
89	  processor and a peripheral, such as a display or a framebuffer chip.
90
91	  See http://www.mipi.org/ for DSI spesifications.
92
93config OMAP2_DSS_USE_DSI_PLL
94	bool "Use DSI PLL for PCLK (EXPERIMENTAL)"
95	default n
96	depends on OMAP2_DSS_DSI
97	help
98	  Use DSI PLL to generate pixel clock.  Currently only for DPI output.
99	  DSI PLL can be used to generate higher and more precise pixel clocks.
100
101config OMAP2_DSS_FAKE_VSYNC
102	bool "Fake VSYNC irq from manual update displays"
103	default n
104	help
105	  If this is selected, DSI will generate a fake DISPC VSYNC interrupt
106	  when DSI has sent a frame. This is only needed with DSI or RFBI
107	  displays using manual mode, and you want VSYNC to, for example,
108	  time animation.
109
110config OMAP2_DSS_MIN_FCK_PER_PCK
111	int "Minimum FCK/PCK ratio (for scaling)"
112	range 0 32
113	default 0
114	help
115	  This can be used to adjust the minimum FCK/PCK ratio.
116
117	  With this you can make sure that DISPC FCK is at least
118	  n x PCK. Video plane scaling requires higher FCK than
119	  normally.
120
121	  If this is set to 0, there's no extra constraint on the
122	  DISPC FCK. However, the FCK will at minimum be
123	  2xPCK (if active matrix) or 3xPCK (if passive matrix).
124
125	  Max FCK is 173MHz, so this doesn't work if your PCK
126	  is very high.
127
128endif
129