1 /* SPDX-License-Identifier: GPL-2.0 */
2 #ifndef B43_H_
3 #define B43_H_
4
5 #include <linux/kernel.h>
6 #include <linux/spinlock.h>
7 #include <linux/interrupt.h>
8 #include <linux/hw_random.h>
9 #include <linux/bcma/bcma.h>
10 #include <linux/ssb/ssb.h>
11 #include <linux/completion.h>
12 #include <net/mac80211.h>
13
14 #include "debugfs.h"
15 #include "leds.h"
16 #include "rfkill.h"
17 #include "bus.h"
18 #include "lo.h"
19 #include "phy_common.h"
20
21
22 #ifdef CONFIG_B43_DEBUG
23 # define B43_DEBUG 1
24 #else
25 # define B43_DEBUG 0
26 #endif
27
28 /* MMIO offsets */
29 #define B43_MMIO_DMA0_REASON 0x20
30 #define B43_MMIO_DMA0_IRQ_MASK 0x24
31 #define B43_MMIO_DMA1_REASON 0x28
32 #define B43_MMIO_DMA1_IRQ_MASK 0x2C
33 #define B43_MMIO_DMA2_REASON 0x30
34 #define B43_MMIO_DMA2_IRQ_MASK 0x34
35 #define B43_MMIO_DMA3_REASON 0x38
36 #define B43_MMIO_DMA3_IRQ_MASK 0x3C
37 #define B43_MMIO_DMA4_REASON 0x40
38 #define B43_MMIO_DMA4_IRQ_MASK 0x44
39 #define B43_MMIO_DMA5_REASON 0x48
40 #define B43_MMIO_DMA5_IRQ_MASK 0x4C
41 #define B43_MMIO_MACCTL 0x120 /* MAC control */
42 #define B43_MMIO_MACCMD 0x124 /* MAC command */
43 #define B43_MMIO_GEN_IRQ_REASON 0x128
44 #define B43_MMIO_GEN_IRQ_MASK 0x12C
45 #define B43_MMIO_RAM_CONTROL 0x130
46 #define B43_MMIO_RAM_DATA 0x134
47 #define B43_MMIO_PS_STATUS 0x140
48 #define B43_MMIO_RADIO_HWENABLED_HI 0x158
49 #define B43_MMIO_MAC_HW_CAP 0x15C /* MAC capabilities (corerev >= 13) */
50 #define B43_MMIO_SHM_CONTROL 0x160
51 #define B43_MMIO_SHM_DATA 0x164
52 #define B43_MMIO_SHM_DATA_UNALIGNED 0x166
53 #define B43_MMIO_XMITSTAT_0 0x170
54 #define B43_MMIO_XMITSTAT_1 0x174
55 #define B43_MMIO_REV3PLUS_TSF_LOW 0x180 /* core rev >= 3 only */
56 #define B43_MMIO_REV3PLUS_TSF_HIGH 0x184 /* core rev >= 3 only */
57 #define B43_MMIO_TSF_CFP_REP 0x188
58 #define B43_MMIO_TSF_CFP_START 0x18C
59 #define B43_MMIO_TSF_CFP_MAXDUR 0x190
60
61 /* 32-bit DMA */
62 #define B43_MMIO_DMA32_BASE0 0x200
63 #define B43_MMIO_DMA32_BASE1 0x220
64 #define B43_MMIO_DMA32_BASE2 0x240
65 #define B43_MMIO_DMA32_BASE3 0x260
66 #define B43_MMIO_DMA32_BASE4 0x280
67 #define B43_MMIO_DMA32_BASE5 0x2A0
68 /* 64-bit DMA */
69 #define B43_MMIO_DMA64_BASE0 0x200
70 #define B43_MMIO_DMA64_BASE1 0x240
71 #define B43_MMIO_DMA64_BASE2 0x280
72 #define B43_MMIO_DMA64_BASE3 0x2C0
73 #define B43_MMIO_DMA64_BASE4 0x300
74 #define B43_MMIO_DMA64_BASE5 0x340
75
76 /* PIO on core rev < 11 */
77 #define B43_MMIO_PIO_BASE0 0x300
78 #define B43_MMIO_PIO_BASE1 0x310
79 #define B43_MMIO_PIO_BASE2 0x320
80 #define B43_MMIO_PIO_BASE3 0x330
81 #define B43_MMIO_PIO_BASE4 0x340
82 #define B43_MMIO_PIO_BASE5 0x350
83 #define B43_MMIO_PIO_BASE6 0x360
84 #define B43_MMIO_PIO_BASE7 0x370
85 /* PIO on core rev >= 11 */
86 #define B43_MMIO_PIO11_BASE0 0x200
87 #define B43_MMIO_PIO11_BASE1 0x240
88 #define B43_MMIO_PIO11_BASE2 0x280
89 #define B43_MMIO_PIO11_BASE3 0x2C0
90 #define B43_MMIO_PIO11_BASE4 0x300
91 #define B43_MMIO_PIO11_BASE5 0x340
92
93 #define B43_MMIO_RADIO24_CONTROL 0x3D8 /* core rev >= 24 only */
94 #define B43_MMIO_RADIO24_DATA 0x3DA /* core rev >= 24 only */
95 #define B43_MMIO_PHY_VER 0x3E0
96 #define B43_MMIO_PHY_RADIO 0x3E2
97 #define B43_MMIO_PHY0 0x3E6
98 #define B43_MMIO_ANTENNA 0x3E8
99 #define B43_MMIO_CHANNEL 0x3F0
100 #define B43_MMIO_CHANNEL_EXT 0x3F4
101 #define B43_MMIO_RADIO_CONTROL 0x3F6
102 #define B43_MMIO_RADIO_DATA_HIGH 0x3F8
103 #define B43_MMIO_RADIO_DATA_LOW 0x3FA
104 #define B43_MMIO_PHY_CONTROL 0x3FC
105 #define B43_MMIO_PHY_DATA 0x3FE
106 #define B43_MMIO_MACFILTER_CONTROL 0x420
107 #define B43_MMIO_MACFILTER_DATA 0x422
108 #define B43_MMIO_RCMTA_COUNT 0x43C
109 #define B43_MMIO_PSM_PHY_HDR 0x492
110 #define B43_MMIO_RADIO_HWENABLED_LO 0x49A
111 #define B43_MMIO_GPIO_CONTROL 0x49C
112 #define B43_MMIO_GPIO_MASK 0x49E
113 #define B43_MMIO_TXE0_CTL 0x500
114 #define B43_MMIO_TXE0_AUX 0x502
115 #define B43_MMIO_TXE0_TS_LOC 0x504
116 #define B43_MMIO_TXE0_TIME_OUT 0x506
117 #define B43_MMIO_TXE0_WM_0 0x508
118 #define B43_MMIO_TXE0_WM_1 0x50A
119 #define B43_MMIO_TXE0_PHYCTL 0x50C
120 #define B43_MMIO_TXE0_STATUS 0x50E
121 #define B43_MMIO_TXE0_MMPLCP0 0x510
122 #define B43_MMIO_TXE0_MMPLCP1 0x512
123 #define B43_MMIO_TXE0_PHYCTL1 0x514
124 #define B43_MMIO_XMTFIFODEF 0x520
125 #define B43_MMIO_XMTFIFO_FRAME_CNT 0x522 /* core rev>= 16 only */
126 #define B43_MMIO_XMTFIFO_BYTE_CNT 0x524 /* core rev>= 16 only */
127 #define B43_MMIO_XMTFIFO_HEAD 0x526 /* core rev>= 16 only */
128 #define B43_MMIO_XMTFIFO_RD_PTR 0x528 /* core rev>= 16 only */
129 #define B43_MMIO_XMTFIFO_WR_PTR 0x52A /* core rev>= 16 only */
130 #define B43_MMIO_XMTFIFODEF1 0x52C /* core rev>= 16 only */
131 #define B43_MMIO_XMTFIFOCMD 0x540
132 #define B43_MMIO_XMTFIFOFLUSH 0x542
133 #define B43_MMIO_XMTFIFOTHRESH 0x544
134 #define B43_MMIO_XMTFIFORDY 0x546
135 #define B43_MMIO_XMTFIFOPRIRDY 0x548
136 #define B43_MMIO_XMTFIFORQPRI 0x54A
137 #define B43_MMIO_XMTTPLATETXPTR 0x54C
138 #define B43_MMIO_XMTTPLATEPTR 0x550
139 #define B43_MMIO_SMPL_CLCT_STRPTR 0x552 /* core rev>= 22 only */
140 #define B43_MMIO_SMPL_CLCT_STPPTR 0x554 /* core rev>= 22 only */
141 #define B43_MMIO_SMPL_CLCT_CURPTR 0x556 /* core rev>= 22 only */
142 #define B43_MMIO_XMTTPLATEDATALO 0x560
143 #define B43_MMIO_XMTTPLATEDATAHI 0x562
144 #define B43_MMIO_XMTSEL 0x568
145 #define B43_MMIO_XMTTXCNT 0x56A
146 #define B43_MMIO_XMTTXSHMADDR 0x56C
147 #define B43_MMIO_TSF_CFP_START_LOW 0x604
148 #define B43_MMIO_TSF_CFP_START_HIGH 0x606
149 #define B43_MMIO_TSF_CFP_PRETBTT 0x612
150 #define B43_MMIO_TSF_CLK_FRAC_LOW 0x62E
151 #define B43_MMIO_TSF_CLK_FRAC_HIGH 0x630
152 #define B43_MMIO_TSF_0 0x632 /* core rev < 3 only */
153 #define B43_MMIO_TSF_1 0x634 /* core rev < 3 only */
154 #define B43_MMIO_TSF_2 0x636 /* core rev < 3 only */
155 #define B43_MMIO_TSF_3 0x638 /* core rev < 3 only */
156 #define B43_MMIO_RNG 0x65A
157 #define B43_MMIO_IFSSLOT 0x684 /* Interframe slot time */
158 #define B43_MMIO_IFSCTL 0x688 /* Interframe space control */
159 #define B43_MMIO_IFSSTAT 0x690
160 #define B43_MMIO_IFSMEDBUSYCTL 0x692
161 #define B43_MMIO_IFTXDUR 0x694
162 #define B43_MMIO_IFSCTL_USE_EDCF 0x0004
163 #define B43_MMIO_POWERUP_DELAY 0x6A8
164 #define B43_MMIO_BTCOEX_CTL 0x6B4 /* Bluetooth Coexistence Control */
165 #define B43_MMIO_BTCOEX_STAT 0x6B6 /* Bluetooth Coexistence Status */
166 #define B43_MMIO_BTCOEX_TXCTL 0x6B8 /* Bluetooth Coexistence Transmit Control */
167 #define B43_MMIO_WEPCTL 0x7C0
168
169 /* SPROM boardflags_lo values */
170 #define B43_BFL_BTCOEXIST 0x0001 /* implements Bluetooth coexistance */
171 #define B43_BFL_PACTRL 0x0002 /* GPIO 9 controlling the PA */
172 #define B43_BFL_AIRLINEMODE 0x0004 /* implements GPIO 13 radio disable indication */
173 #define B43_BFL_RSSI 0x0008 /* software calculates nrssi slope. */
174 #define B43_BFL_ENETSPI 0x0010 /* has ephy roboswitch spi */
175 #define B43_BFL_XTAL_NOSLOW 0x0020 /* no slow clock available */
176 #define B43_BFL_CCKHIPWR 0x0040 /* can do high power CCK transmission */
177 #define B43_BFL_ENETADM 0x0080 /* has ADMtek switch */
178 #define B43_BFL_ENETVLAN 0x0100 /* can do vlan */
179 #define B43_BFL_AFTERBURNER 0x0200 /* supports Afterburner mode */
180 #define B43_BFL_NOPCI 0x0400 /* leaves PCI floating */
181 #define B43_BFL_FEM 0x0800 /* supports the Front End Module */
182 #define B43_BFL_EXTLNA 0x1000 /* has an external LNA */
183 #define B43_BFL_HGPA 0x2000 /* had high gain PA */
184 #define B43_BFL_BTCMOD 0x4000 /* BFL_BTCOEXIST is given in alternate GPIOs */
185 #define B43_BFL_ALTIQ 0x8000 /* alternate I/Q settings */
186
187 /* SPROM boardflags_hi values */
188 #define B43_BFH_NOPA 0x0001 /* has no PA */
189 #define B43_BFH_RSSIINV 0x0002 /* RSSI uses positive slope (not TSSI) */
190 #define B43_BFH_PAREF 0x0004 /* uses the PARef LDO */
191 #define B43_BFH_3TSWITCH 0x0008 /* uses a triple throw switch shared
192 * with bluetooth */
193 #define B43_BFH_PHASESHIFT 0x0010 /* can support phase shifter */
194 #define B43_BFH_BUCKBOOST 0x0020 /* has buck/booster */
195 #define B43_BFH_FEM_BT 0x0040 /* has FEM and switch to share antenna
196 * with bluetooth */
197 #define B43_BFH_NOCBUCK 0x0080
198 #define B43_BFH_PALDO 0x0200
199 #define B43_BFH_EXTLNA_5GHZ 0x1000 /* has an external LNA (5GHz mode) */
200
201 /* SPROM boardflags2_lo values */
202 #define B43_BFL2_RXBB_INT_REG_DIS 0x0001 /* external RX BB regulator present */
203 #define B43_BFL2_APLL_WAR 0x0002 /* alternative A-band PLL settings implemented */
204 #define B43_BFL2_TXPWRCTRL_EN 0x0004 /* permits enabling TX Power Control */
205 #define B43_BFL2_2X4_DIV 0x0008 /* 2x4 diversity switch */
206 #define B43_BFL2_5G_PWRGAIN 0x0010 /* supports 5G band power gain */
207 #define B43_BFL2_PCIEWAR_OVR 0x0020 /* overrides ASPM and Clkreq settings */
208 #define B43_BFL2_CAESERS_BRD 0x0040 /* is Caesers board (unused) */
209 #define B43_BFL2_BTC3WIRE 0x0080 /* used 3-wire bluetooth coexist */
210 #define B43_BFL2_SKWRKFEM_BRD 0x0100 /* 4321mcm93 uses Skyworks FEM */
211 #define B43_BFL2_SPUR_WAR 0x0200 /* has a workaround for clock-harmonic spurs */
212 #define B43_BFL2_GPLL_WAR 0x0400 /* altenative G-band PLL settings implemented */
213 #define B43_BFL2_SINGLEANT_CCK 0x1000
214 #define B43_BFL2_2G_SPUR_WAR 0x2000
215
216 /* SPROM boardflags2_hi values */
217 #define B43_BFH2_GPLL_WAR2 0x0001
218 #define B43_BFH2_IPALVLSHIFT_3P3 0x0002
219 #define B43_BFH2_INTERNDET_TXIQCAL 0x0004
220 #define B43_BFH2_XTALBUFOUTEN 0x0008
221
222 /* GPIO register offset, in both ChipCommon and PCI core. */
223 #define B43_GPIO_CONTROL 0x6c
224
225 /* SHM Routing */
226 enum {
227 B43_SHM_UCODE, /* Microcode memory */
228 B43_SHM_SHARED, /* Shared memory */
229 B43_SHM_SCRATCH, /* Scratch memory */
230 B43_SHM_HW, /* Internal hardware register */
231 B43_SHM_RCMTA, /* Receive match transmitter address (rev >= 5 only) */
232 };
233 /* SHM Routing modifiers */
234 #define B43_SHM_AUTOINC_R 0x0200 /* Auto-increment address on read */
235 #define B43_SHM_AUTOINC_W 0x0100 /* Auto-increment address on write */
236 #define B43_SHM_AUTOINC_RW (B43_SHM_AUTOINC_R | \
237 B43_SHM_AUTOINC_W)
238
239 /* Misc SHM_SHARED offsets */
240 #define B43_SHM_SH_WLCOREREV 0x0016 /* 802.11 core revision */
241 #define B43_SHM_SH_PCTLWDPOS 0x0008
242 #define B43_SHM_SH_RXPADOFF 0x0034 /* RX Padding data offset (PIO only) */
243 #define B43_SHM_SH_FWCAPA 0x0042 /* Firmware capabilities (Opensource firmware only) */
244 #define B43_SHM_SH_PHYVER 0x0050 /* PHY version */
245 #define B43_SHM_SH_PHYTYPE 0x0052 /* PHY type */
246 #define B43_SHM_SH_ANTSWAP 0x005C /* Antenna swap threshold */
247 #define B43_SHM_SH_HOSTF1 0x005E /* Hostflags 1 for ucode options */
248 #define B43_SHM_SH_HOSTF2 0x0060 /* Hostflags 2 for ucode options */
249 #define B43_SHM_SH_HOSTF3 0x0062 /* Hostflags 3 for ucode options */
250 #define B43_SHM_SH_RFATT 0x0064 /* Current radio attenuation value */
251 #define B43_SHM_SH_RADAR 0x0066 /* Radar register */
252 #define B43_SHM_SH_PHYTXNOI 0x006E /* PHY noise directly after TX (lower 8bit only) */
253 #define B43_SHM_SH_RFRXSP1 0x0072 /* RF RX SP Register 1 */
254 #define B43_SHM_SH_HOSTF4 0x0078 /* Hostflags 4 for ucode options */
255 #define B43_SHM_SH_CHAN 0x00A0 /* Current channel (low 8bit only) */
256 #define B43_SHM_SH_CHAN_5GHZ 0x0100 /* Bit set, if 5 Ghz channel */
257 #define B43_SHM_SH_CHAN_40MHZ 0x0200 /* Bit set, if 40 Mhz channel width */
258 #define B43_SHM_SH_MACHW_L 0x00C0 /* Location where the ucode expects the MAC capabilities */
259 #define B43_SHM_SH_MACHW_H 0x00C2 /* Location where the ucode expects the MAC capabilities */
260 #define B43_SHM_SH_HOSTF5 0x00D4 /* Hostflags 5 for ucode options */
261 #define B43_SHM_SH_BCMCFIFOID 0x0108 /* Last posted cookie to the bcast/mcast FIFO */
262 /* TSSI information */
263 #define B43_SHM_SH_TSSI_CCK 0x0058 /* TSSI for last 4 CCK frames (32bit) */
264 #define B43_SHM_SH_TSSI_OFDM_A 0x0068 /* TSSI for last 4 OFDM frames (32bit) */
265 #define B43_SHM_SH_TSSI_OFDM_G 0x0070 /* TSSI for last 4 OFDM frames (32bit) */
266 #define B43_TSSI_MAX 0x7F /* Max value for one TSSI value */
267 /* SHM_SHARED TX FIFO variables */
268 #define B43_SHM_SH_SIZE01 0x0098 /* TX FIFO size for FIFO 0 (low) and 1 (high) */
269 #define B43_SHM_SH_SIZE23 0x009A /* TX FIFO size for FIFO 2 and 3 */
270 #define B43_SHM_SH_SIZE45 0x009C /* TX FIFO size for FIFO 4 and 5 */
271 #define B43_SHM_SH_SIZE67 0x009E /* TX FIFO size for FIFO 6 and 7 */
272 /* SHM_SHARED background noise */
273 #define B43_SHM_SH_JSSI0 0x0088 /* Measure JSSI 0 */
274 #define B43_SHM_SH_JSSI1 0x008A /* Measure JSSI 1 */
275 #define B43_SHM_SH_JSSIAUX 0x008C /* Measure JSSI AUX */
276 /* SHM_SHARED crypto engine */
277 #define B43_SHM_SH_DEFAULTIV 0x003C /* Default IV location */
278 #define B43_SHM_SH_NRRXTRANS 0x003E /* # of soft RX transmitter addresses (max 8) */
279 #define B43_SHM_SH_KTP 0x0056 /* Key table pointer */
280 #define B43_SHM_SH_TKIPTSCTTAK 0x0318
281 #define B43_SHM_SH_KEYIDXBLOCK 0x05D4 /* Key index/algorithm block (v4 firmware) */
282 #define B43_SHM_SH_PSM 0x05F4 /* PSM transmitter address match block (rev < 5) */
283 /* SHM_SHARED WME variables */
284 #define B43_SHM_SH_EDCFSTAT 0x000E /* EDCF status */
285 #define B43_SHM_SH_TXFCUR 0x0030 /* TXF current index */
286 #define B43_SHM_SH_EDCFQ 0x0240 /* EDCF Q info */
287 /* SHM_SHARED powersave mode related */
288 #define B43_SHM_SH_SLOTT 0x0010 /* Slot time */
289 #define B43_SHM_SH_DTIMPER 0x0012 /* DTIM period */
290 #define B43_SHM_SH_NOSLPZNATDTIM 0x004C /* NOSLPZNAT DTIM */
291 /* SHM_SHARED beacon/AP variables */
292 #define B43_SHM_SH_BT_BASE0 0x0068 /* Beacon template base 0 */
293 #define B43_SHM_SH_BTL0 0x0018 /* Beacon template length 0 */
294 #define B43_SHM_SH_BT_BASE1 0x0468 /* Beacon template base 1 */
295 #define B43_SHM_SH_BTL1 0x001A /* Beacon template length 1 */
296 #define B43_SHM_SH_BTSFOFF 0x001C /* Beacon TSF offset */
297 #define B43_SHM_SH_TIMBPOS 0x001E /* TIM B position in beacon */
298 #define B43_SHM_SH_DTIMP 0x0012 /* DTIP period */
299 #define B43_SHM_SH_MCASTCOOKIE 0x00A8 /* Last bcast/mcast frame ID */
300 #define B43_SHM_SH_SFFBLIM 0x0044 /* Short frame fallback retry limit */
301 #define B43_SHM_SH_LFFBLIM 0x0046 /* Long frame fallback retry limit */
302 #define B43_SHM_SH_BEACPHYCTL 0x0054 /* Beacon PHY TX control word (see PHY TX control) */
303 #define B43_SHM_SH_EXTNPHYCTL 0x00B0 /* Extended bytes for beacon PHY control (N) */
304 #define B43_SHM_SH_BCN_LI 0x00B6 /* beacon listen interval */
305 /* SHM_SHARED ACK/CTS control */
306 #define B43_SHM_SH_ACKCTSPHYCTL 0x0022 /* ACK/CTS PHY control word (see PHY TX control) */
307 /* SHM_SHARED probe response variables */
308 #define B43_SHM_SH_PRSSID 0x0160 /* Probe Response SSID */
309 #define B43_SHM_SH_PRSSIDLEN 0x0048 /* Probe Response SSID length */
310 #define B43_SHM_SH_PRTLEN 0x004A /* Probe Response template length */
311 #define B43_SHM_SH_PRMAXTIME 0x0074 /* Probe Response max time */
312 #define B43_SHM_SH_PRPHYCTL 0x0188 /* Probe Response PHY TX control word */
313 /* SHM_SHARED rate tables */
314 #define B43_SHM_SH_OFDMDIRECT 0x01C0 /* Pointer to OFDM direct map */
315 #define B43_SHM_SH_OFDMBASIC 0x01E0 /* Pointer to OFDM basic rate map */
316 #define B43_SHM_SH_CCKDIRECT 0x0200 /* Pointer to CCK direct map */
317 #define B43_SHM_SH_CCKBASIC 0x0220 /* Pointer to CCK basic rate map */
318 /* SHM_SHARED microcode soft registers */
319 #define B43_SHM_SH_UCODEREV 0x0000 /* Microcode revision */
320 #define B43_SHM_SH_UCODEPATCH 0x0002 /* Microcode patchlevel */
321 #define B43_SHM_SH_UCODEDATE 0x0004 /* Microcode date */
322 #define B43_SHM_SH_UCODETIME 0x0006 /* Microcode time */
323 #define B43_SHM_SH_UCODESTAT 0x0040 /* Microcode debug status code */
324 #define B43_SHM_SH_UCODESTAT_INVALID 0
325 #define B43_SHM_SH_UCODESTAT_INIT 1
326 #define B43_SHM_SH_UCODESTAT_ACTIVE 2
327 #define B43_SHM_SH_UCODESTAT_SUSP 3 /* suspended */
328 #define B43_SHM_SH_UCODESTAT_SLEEP 4 /* asleep (PS) */
329 #define B43_SHM_SH_MAXBFRAMES 0x0080 /* Maximum number of frames in a burst */
330 #define B43_SHM_SH_SPUWKUP 0x0094 /* pre-wakeup for synth PU in us */
331 #define B43_SHM_SH_PRETBTT 0x0096 /* pre-TBTT in us */
332 /* SHM_SHARED tx iq workarounds */
333 #define B43_SHM_SH_NPHY_TXIQW0 0x0700
334 #define B43_SHM_SH_NPHY_TXIQW1 0x0702
335 #define B43_SHM_SH_NPHY_TXIQW2 0x0704
336 #define B43_SHM_SH_NPHY_TXIQW3 0x0706
337 /* SHM_SHARED tx pwr ctrl */
338 #define B43_SHM_SH_NPHY_TXPWR_INDX0 0x0708
339 #define B43_SHM_SH_NPHY_TXPWR_INDX1 0x070E
340
341 /* SHM_SCRATCH offsets */
342 #define B43_SHM_SC_MINCONT 0x0003 /* Minimum contention window */
343 #define B43_SHM_SC_MAXCONT 0x0004 /* Maximum contention window */
344 #define B43_SHM_SC_CURCONT 0x0005 /* Current contention window */
345 #define B43_SHM_SC_SRLIMIT 0x0006 /* Short retry count limit */
346 #define B43_SHM_SC_LRLIMIT 0x0007 /* Long retry count limit */
347 #define B43_SHM_SC_DTIMC 0x0008 /* Current DTIM count */
348 #define B43_SHM_SC_BTL0LEN 0x0015 /* Beacon 0 template length */
349 #define B43_SHM_SC_BTL1LEN 0x0016 /* Beacon 1 template length */
350 #define B43_SHM_SC_SCFB 0x0017 /* Short frame transmit count threshold for rate fallback */
351 #define B43_SHM_SC_LCFB 0x0018 /* Long frame transmit count threshold for rate fallback */
352
353 /* Hardware Radio Enable masks */
354 #define B43_MMIO_RADIO_HWENABLED_HI_MASK (1 << 16)
355 #define B43_MMIO_RADIO_HWENABLED_LO_MASK (1 << 4)
356
357 /* HostFlags. See b43_hf_read/write() */
358 #define B43_HF_ANTDIVHELP 0x000000000001ULL /* ucode antenna div helper */
359 #define B43_HF_SYMW 0x000000000002ULL /* G-PHY SYM workaround */
360 #define B43_HF_RXPULLW 0x000000000004ULL /* RX pullup workaround */
361 #define B43_HF_CCKBOOST 0x000000000008ULL /* 4dB CCK power boost (exclusive with OFDM boost) */
362 #define B43_HF_BTCOEX 0x000000000010ULL /* Bluetooth coexistance */
363 #define B43_HF_GDCW 0x000000000020ULL /* G-PHY DC canceller filter bw workaround */
364 #define B43_HF_OFDMPABOOST 0x000000000040ULL /* Enable PA gain boost for OFDM */
365 #define B43_HF_ACPR 0x000000000080ULL /* Disable for Japan, channel 14 */
366 #define B43_HF_EDCF 0x000000000100ULL /* on if WME and MAC suspended */
367 #define B43_HF_TSSIRPSMW 0x000000000200ULL /* TSSI reset PSM ucode workaround */
368 #define B43_HF_20IN40IQW 0x000000000200ULL /* 20 in 40 MHz I/Q workaround (rev >= 13 only) */
369 #define B43_HF_DSCRQ 0x000000000400ULL /* Disable slow clock request in ucode */
370 #define B43_HF_ACIW 0x000000000800ULL /* ACI workaround: shift bits by 2 on PHY CRS */
371 #define B43_HF_2060W 0x000000001000ULL /* 2060 radio workaround */
372 #define B43_HF_RADARW 0x000000002000ULL /* Radar workaround */
373 #define B43_HF_USEDEFKEYS 0x000000004000ULL /* Enable use of default keys */
374 #define B43_HF_AFTERBURNER 0x000000008000ULL /* Afterburner enabled */
375 #define B43_HF_BT4PRIOCOEX 0x000000010000ULL /* Bluetooth 4-priority coexistance */
376 #define B43_HF_FWKUP 0x000000020000ULL /* Fast wake-up ucode */
377 #define B43_HF_VCORECALC 0x000000040000ULL /* Force VCO recalculation when powering up synthpu */
378 #define B43_HF_PCISCW 0x000000080000ULL /* PCI slow clock workaround */
379 #define B43_HF_4318TSSI 0x000000200000ULL /* 4318 TSSI */
380 #define B43_HF_FBCMCFIFO 0x000000400000ULL /* Flush bcast/mcast FIFO immediately */
381 #define B43_HF_HWPCTL 0x000000800000ULL /* Enable hardwarre power control */
382 #define B43_HF_BTCOEXALT 0x000001000000ULL /* Bluetooth coexistance in alternate pins */
383 #define B43_HF_TXBTCHECK 0x000002000000ULL /* Bluetooth check during transmission */
384 #define B43_HF_SKCFPUP 0x000004000000ULL /* Skip CFP update */
385 #define B43_HF_N40W 0x000008000000ULL /* N PHY 40 MHz workaround (rev >= 13 only) */
386 #define B43_HF_ANTSEL 0x000020000000ULL /* Antenna selection (for testing antenna div.) */
387 #define B43_HF_BT3COEXT 0x000020000000ULL /* Bluetooth 3-wire coexistence (rev >= 13 only) */
388 #define B43_HF_BTCANT 0x000040000000ULL /* Bluetooth coexistence (antenna mode) (rev >= 13 only) */
389 #define B43_HF_ANTSELEN 0x000100000000ULL /* Antenna selection enabled (rev >= 13 only) */
390 #define B43_HF_ANTSELMODE 0x000200000000ULL /* Antenna selection mode (rev >= 13 only) */
391 #define B43_HF_MLADVW 0x001000000000ULL /* N PHY ML ADV workaround (rev >= 13 only) */
392 #define B43_HF_PR45960W 0x080000000000ULL /* PR 45960 workaround (rev >= 13 only) */
393
394 /* Firmware capabilities field in SHM (Opensource firmware only) */
395 #define B43_FWCAPA_HWCRYPTO 0x0001
396 #define B43_FWCAPA_QOS 0x0002
397
398 /* MacFilter offsets. */
399 #define B43_MACFILTER_SELF 0x0000
400 #define B43_MACFILTER_BSSID 0x0003
401
402 /* PowerControl */
403 #define B43_PCTL_IN 0xB0
404 #define B43_PCTL_OUT 0xB4
405 #define B43_PCTL_OUTENABLE 0xB8
406 #define B43_PCTL_XTAL_POWERUP 0x40
407 #define B43_PCTL_PLL_POWERDOWN 0x80
408
409 /* PowerControl Clock Modes */
410 #define B43_PCTL_CLK_FAST 0x00
411 #define B43_PCTL_CLK_SLOW 0x01
412 #define B43_PCTL_CLK_DYNAMIC 0x02
413
414 #define B43_PCTL_FORCE_SLOW 0x0800
415 #define B43_PCTL_FORCE_PLL 0x1000
416 #define B43_PCTL_DYN_XTAL 0x2000
417
418 /* PHYVersioning */
419 #define B43_PHYTYPE_A 0x00
420 #define B43_PHYTYPE_B 0x01
421 #define B43_PHYTYPE_G 0x02
422 #define B43_PHYTYPE_N 0x04
423 #define B43_PHYTYPE_LP 0x05
424 #define B43_PHYTYPE_SSLPN 0x06
425 #define B43_PHYTYPE_HT 0x07
426 #define B43_PHYTYPE_LCN 0x08
427 #define B43_PHYTYPE_LCNXN 0x09
428 #define B43_PHYTYPE_LCN40 0x0a
429 #define B43_PHYTYPE_AC 0x0b
430
431 /* PHYRegisters */
432 #define B43_PHY_ILT_A_CTRL 0x0072
433 #define B43_PHY_ILT_A_DATA1 0x0073
434 #define B43_PHY_ILT_A_DATA2 0x0074
435 #define B43_PHY_G_LO_CONTROL 0x0810
436 #define B43_PHY_ILT_G_CTRL 0x0472
437 #define B43_PHY_ILT_G_DATA1 0x0473
438 #define B43_PHY_ILT_G_DATA2 0x0474
439 #define B43_PHY_A_PCTL 0x007B
440 #define B43_PHY_G_PCTL 0x0029
441 #define B43_PHY_A_CRS 0x0029
442 #define B43_PHY_RADIO_BITFIELD 0x0401
443 #define B43_PHY_G_CRS 0x0429
444 #define B43_PHY_NRSSILT_CTRL 0x0803
445 #define B43_PHY_NRSSILT_DATA 0x0804
446
447 /* RadioRegisters */
448 #define B43_RADIOCTL_ID 0x01
449
450 /* MAC Control bitfield */
451 #define B43_MACCTL_ENABLED 0x00000001 /* MAC Enabled */
452 #define B43_MACCTL_PSM_RUN 0x00000002 /* Run Microcode */
453 #define B43_MACCTL_PSM_JMP0 0x00000004 /* Microcode jump to 0 */
454 #define B43_MACCTL_SHM_ENABLED 0x00000100 /* SHM Enabled */
455 #define B43_MACCTL_SHM_UPPER 0x00000200 /* SHM Upper */
456 #define B43_MACCTL_IHR_ENABLED 0x00000400 /* IHR Region Enabled */
457 #define B43_MACCTL_PSM_DBG 0x00002000 /* Microcode debugging enabled */
458 #define B43_MACCTL_GPOUTSMSK 0x0000C000 /* GPOUT Select Mask */
459 #define B43_MACCTL_BE 0x00010000 /* Big Endian mode */
460 #define B43_MACCTL_INFRA 0x00020000 /* Infrastructure mode */
461 #define B43_MACCTL_AP 0x00040000 /* AccessPoint mode */
462 #define B43_MACCTL_RADIOLOCK 0x00080000 /* Radio lock */
463 #define B43_MACCTL_BEACPROMISC 0x00100000 /* Beacon Promiscuous */
464 #define B43_MACCTL_KEEP_BADPLCP 0x00200000 /* Keep frames with bad PLCP */
465 #define B43_MACCTL_PHY_LOCK 0x00200000
466 #define B43_MACCTL_KEEP_CTL 0x00400000 /* Keep control frames */
467 #define B43_MACCTL_KEEP_BAD 0x00800000 /* Keep bad frames (FCS) */
468 #define B43_MACCTL_PROMISC 0x01000000 /* Promiscuous mode */
469 #define B43_MACCTL_HWPS 0x02000000 /* Hardware Power Saving */
470 #define B43_MACCTL_AWAKE 0x04000000 /* Device is awake */
471 #define B43_MACCTL_CLOSEDNET 0x08000000 /* Closed net (no SSID bcast) */
472 #define B43_MACCTL_TBTTHOLD 0x10000000 /* TBTT Hold */
473 #define B43_MACCTL_DISCTXSTAT 0x20000000 /* Discard TX status */
474 #define B43_MACCTL_DISCPMQ 0x40000000 /* Discard Power Management Queue */
475 #define B43_MACCTL_GMODE 0x80000000 /* G Mode */
476
477 /* MAC Command bitfield */
478 #define B43_MACCMD_BEACON0_VALID 0x00000001 /* Beacon 0 in template RAM is busy/valid */
479 #define B43_MACCMD_BEACON1_VALID 0x00000002 /* Beacon 1 in template RAM is busy/valid */
480 #define B43_MACCMD_DFQ_VALID 0x00000004 /* Directed frame queue valid (IBSS PS mode, ATIM) */
481 #define B43_MACCMD_CCA 0x00000008 /* Clear channel assessment */
482 #define B43_MACCMD_BGNOISE 0x00000010 /* Background noise */
483
484 /* B43_MMIO_PSM_PHY_HDR bits */
485 #define B43_PSM_HDR_MAC_PHY_RESET 0x00000001
486 #define B43_PSM_HDR_MAC_PHY_CLOCK_EN 0x00000002
487 #define B43_PSM_HDR_MAC_PHY_FORCE_CLK 0x00000004
488
489 /* See BCMA_CLKCTLST_EXTRESREQ and BCMA_CLKCTLST_EXTRESST */
490 #define B43_BCMA_CLKCTLST_80211_PLL_REQ 0x00000100
491 #define B43_BCMA_CLKCTLST_PHY_PLL_REQ 0x00000200
492 #define B43_BCMA_CLKCTLST_80211_PLL_ST 0x01000000
493 #define B43_BCMA_CLKCTLST_PHY_PLL_ST 0x02000000
494
495 /* BCMA 802.11 core specific IO Control (BCMA_IOCTL) flags */
496 #define B43_BCMA_IOCTL_PHY_CLKEN 0x00000004 /* PHY Clock Enable */
497 #define B43_BCMA_IOCTL_PHY_RESET 0x00000008 /* PHY Reset */
498 #define B43_BCMA_IOCTL_MACPHYCLKEN 0x00000010 /* MAC PHY Clock Control Enable */
499 #define B43_BCMA_IOCTL_PLLREFSEL 0x00000020 /* PLL Frequency Reference Select */
500 #define B43_BCMA_IOCTL_PHY_BW 0x000000C0 /* PHY band width and clock speed mask (N-PHY+ only?) */
501 #define B43_BCMA_IOCTL_PHY_BW_10MHZ 0x00000000 /* 10 MHz bandwidth, 40 MHz PHY */
502 #define B43_BCMA_IOCTL_PHY_BW_20MHZ 0x00000040 /* 20 MHz bandwidth, 80 MHz PHY */
503 #define B43_BCMA_IOCTL_PHY_BW_40MHZ 0x00000080 /* 40 MHz bandwidth, 160 MHz PHY */
504 #define B43_BCMA_IOCTL_PHY_BW_80MHZ 0x000000C0 /* 80 MHz bandwidth */
505 #define B43_BCMA_IOCTL_DAC 0x00000300 /* Highspeed DAC mode control field */
506 #define B43_BCMA_IOCTL_GMODE 0x00002000 /* G Mode Enable */
507
508 /* BCMA 802.11 core specific IO status (BCMA_IOST) flags */
509 #define B43_BCMA_IOST_2G_PHY 0x00000001 /* 2.4G capable phy */
510 #define B43_BCMA_IOST_5G_PHY 0x00000002 /* 5G capable phy */
511 #define B43_BCMA_IOST_FASTCLKA 0x00000004 /* Fast Clock Available */
512 #define B43_BCMA_IOST_DUALB_PHY 0x00000008 /* Dualband phy */
513
514 /* 802.11 core specific TM State Low (SSB_TMSLOW) flags */
515 #define B43_TMSLOW_GMODE 0x20000000 /* G Mode Enable */
516 #define B43_TMSLOW_PHY_BANDWIDTH 0x00C00000 /* PHY band width and clock speed mask (N-PHY only) */
517 #define B43_TMSLOW_PHY_BANDWIDTH_10MHZ 0x00000000 /* 10 MHz bandwidth, 40 MHz PHY */
518 #define B43_TMSLOW_PHY_BANDWIDTH_20MHZ 0x00400000 /* 20 MHz bandwidth, 80 MHz PHY */
519 #define B43_TMSLOW_PHY_BANDWIDTH_40MHZ 0x00800000 /* 40 MHz bandwidth, 160 MHz PHY */
520 #define B43_TMSLOW_PLLREFSEL 0x00200000 /* PLL Frequency Reference Select (rev >= 5) */
521 #define B43_TMSLOW_MACPHYCLKEN 0x00100000 /* MAC PHY Clock Control Enable (rev >= 5) */
522 #define B43_TMSLOW_PHYRESET 0x00080000 /* PHY Reset */
523 #define B43_TMSLOW_PHYCLKEN 0x00040000 /* PHY Clock Enable */
524
525 /* 802.11 core specific TM State High (SSB_TMSHIGH) flags */
526 #define B43_TMSHIGH_DUALBAND_PHY 0x00080000 /* Dualband PHY available */
527 #define B43_TMSHIGH_FCLOCK 0x00040000 /* Fast Clock Available (rev >= 5) */
528 #define B43_TMSHIGH_HAVE_5GHZ_PHY 0x00020000 /* 5 GHz PHY available (rev >= 5) */
529 #define B43_TMSHIGH_HAVE_2GHZ_PHY 0x00010000 /* 2.4 GHz PHY available (rev >= 5) */
530
531 /* Generic-Interrupt reasons. */
532 #define B43_IRQ_MAC_SUSPENDED 0x00000001
533 #define B43_IRQ_BEACON 0x00000002
534 #define B43_IRQ_TBTT_INDI 0x00000004
535 #define B43_IRQ_BEACON_TX_OK 0x00000008
536 #define B43_IRQ_BEACON_CANCEL 0x00000010
537 #define B43_IRQ_ATIM_END 0x00000020
538 #define B43_IRQ_PMQ 0x00000040
539 #define B43_IRQ_PIO_WORKAROUND 0x00000100
540 #define B43_IRQ_MAC_TXERR 0x00000200
541 #define B43_IRQ_PHY_TXERR 0x00000800
542 #define B43_IRQ_PMEVENT 0x00001000
543 #define B43_IRQ_TIMER0 0x00002000
544 #define B43_IRQ_TIMER1 0x00004000
545 #define B43_IRQ_DMA 0x00008000
546 #define B43_IRQ_TXFIFO_FLUSH_OK 0x00010000
547 #define B43_IRQ_CCA_MEASURE_OK 0x00020000
548 #define B43_IRQ_NOISESAMPLE_OK 0x00040000
549 #define B43_IRQ_UCODE_DEBUG 0x08000000
550 #define B43_IRQ_RFKILL 0x10000000
551 #define B43_IRQ_TX_OK 0x20000000
552 #define B43_IRQ_PHY_G_CHANGED 0x40000000
553 #define B43_IRQ_TIMEOUT 0x80000000
554
555 #define B43_IRQ_ALL 0xFFFFFFFF
556 #define B43_IRQ_MASKTEMPLATE (B43_IRQ_TBTT_INDI | \
557 B43_IRQ_ATIM_END | \
558 B43_IRQ_PMQ | \
559 B43_IRQ_MAC_TXERR | \
560 B43_IRQ_PHY_TXERR | \
561 B43_IRQ_DMA | \
562 B43_IRQ_TXFIFO_FLUSH_OK | \
563 B43_IRQ_NOISESAMPLE_OK | \
564 B43_IRQ_UCODE_DEBUG | \
565 B43_IRQ_RFKILL | \
566 B43_IRQ_TX_OK)
567
568 /* The firmware register to fetch the debug-IRQ reason from. */
569 #define B43_DEBUGIRQ_REASON_REG 63
570 /* Debug-IRQ reasons. */
571 #define B43_DEBUGIRQ_PANIC 0 /* The firmware panic'ed */
572 #define B43_DEBUGIRQ_DUMP_SHM 1 /* Dump shared SHM */
573 #define B43_DEBUGIRQ_DUMP_REGS 2 /* Dump the microcode registers */
574 #define B43_DEBUGIRQ_MARKER 3 /* A "marker" was thrown by the firmware. */
575 #define B43_DEBUGIRQ_ACK 0xFFFF /* The host writes that to ACK the IRQ */
576
577 /* The firmware register that contains the "marker" line. */
578 #define B43_MARKER_ID_REG 2
579 #define B43_MARKER_LINE_REG 3
580
581 /* The firmware register to fetch the panic reason from. */
582 #define B43_FWPANIC_REASON_REG 3
583 /* Firmware panic reason codes */
584 #define B43_FWPANIC_DIE 0 /* Firmware died. Don't auto-restart it. */
585 #define B43_FWPANIC_RESTART 1 /* Firmware died. Schedule a controller reset. */
586
587 /* The firmware register that contains the watchdog counter. */
588 #define B43_WATCHDOG_REG 1
589
590 /* Device specific rate values.
591 * The actual values defined here are (rate_in_mbps * 2).
592 * Some code depends on this. Don't change it. */
593 #define B43_CCK_RATE_1MB 0x02
594 #define B43_CCK_RATE_2MB 0x04
595 #define B43_CCK_RATE_5MB 0x0B
596 #define B43_CCK_RATE_11MB 0x16
597 #define B43_OFDM_RATE_6MB 0x0C
598 #define B43_OFDM_RATE_9MB 0x12
599 #define B43_OFDM_RATE_12MB 0x18
600 #define B43_OFDM_RATE_18MB 0x24
601 #define B43_OFDM_RATE_24MB 0x30
602 #define B43_OFDM_RATE_36MB 0x48
603 #define B43_OFDM_RATE_48MB 0x60
604 #define B43_OFDM_RATE_54MB 0x6C
605 /* Convert a b43 rate value to a rate in 100kbps */
606 #define B43_RATE_TO_BASE100KBPS(rate) (((rate) * 10) / 2)
607
608 #define B43_DEFAULT_SHORT_RETRY_LIMIT 7
609 #define B43_DEFAULT_LONG_RETRY_LIMIT 4
610
611 #define B43_PHY_TX_BADNESS_LIMIT 1000
612
613 /* Max size of a security key */
614 #define B43_SEC_KEYSIZE 16
615 /* Max number of group keys */
616 #define B43_NR_GROUP_KEYS 4
617 /* Max number of pairwise keys */
618 #define B43_NR_PAIRWISE_KEYS 50
619 /* Security algorithms. */
620 enum {
621 B43_SEC_ALGO_NONE = 0, /* unencrypted, as of TX header. */
622 B43_SEC_ALGO_WEP40,
623 B43_SEC_ALGO_TKIP,
624 B43_SEC_ALGO_AES,
625 B43_SEC_ALGO_WEP104,
626 B43_SEC_ALGO_AES_LEGACY,
627 };
628
629 struct b43_dmaring;
630
631 /* The firmware file header */
632 #define B43_FW_TYPE_UCODE 'u'
633 #define B43_FW_TYPE_PCM 'p'
634 #define B43_FW_TYPE_IV 'i'
635 struct b43_fw_header {
636 /* File type */
637 u8 type;
638 /* File format version */
639 u8 ver;
640 u8 __padding[2];
641 /* Size of the data. For ucode and PCM this is in bytes.
642 * For IV this is number-of-ivs. */
643 __be32 size;
644 } __packed;
645
646 /* Initial Value file format */
647 #define B43_IV_OFFSET_MASK 0x7FFF
648 #define B43_IV_32BIT 0x8000
649 struct b43_iv {
650 __be16 offset_size;
651 union {
652 __be16 d16;
653 __be32 d32;
654 } __packed data;
655 } __packed;
656
657
658 /* Data structures for DMA transmission, per 80211 core. */
659 struct b43_dma {
660 struct b43_dmaring *tx_ring_AC_BK; /* Background */
661 struct b43_dmaring *tx_ring_AC_BE; /* Best Effort */
662 struct b43_dmaring *tx_ring_AC_VI; /* Video */
663 struct b43_dmaring *tx_ring_AC_VO; /* Voice */
664 struct b43_dmaring *tx_ring_mcast; /* Multicast */
665
666 struct b43_dmaring *rx_ring;
667
668 u32 translation; /* Routing bits */
669 bool translation_in_low; /* Should translation bit go into low addr? */
670 bool parity; /* Check for parity */
671 };
672
673 struct b43_pio_txqueue;
674 struct b43_pio_rxqueue;
675
676 /* Data structures for PIO transmission, per 80211 core. */
677 struct b43_pio {
678 struct b43_pio_txqueue *tx_queue_AC_BK; /* Background */
679 struct b43_pio_txqueue *tx_queue_AC_BE; /* Best Effort */
680 struct b43_pio_txqueue *tx_queue_AC_VI; /* Video */
681 struct b43_pio_txqueue *tx_queue_AC_VO; /* Voice */
682 struct b43_pio_txqueue *tx_queue_mcast; /* Multicast */
683
684 struct b43_pio_rxqueue *rx_queue;
685 };
686
687 /* Context information for a noise calculation (Link Quality). */
688 struct b43_noise_calculation {
689 bool calculation_running;
690 u8 nr_samples;
691 s8 samples[8][4];
692 };
693
694 struct b43_stats {
695 u8 link_noise;
696 };
697
698 struct b43_key {
699 /* If keyconf is NULL, this key is disabled.
700 * keyconf is a cookie. Don't derefenrence it outside of the set_key
701 * path, because b43 doesn't own it. */
702 struct ieee80211_key_conf *keyconf;
703 u8 algorithm;
704 };
705
706 /* SHM offsets to the QOS data structures for the 4 different queues. */
707 #define B43_QOS_QUEUE_NUM 4
708 #define B43_QOS_PARAMS(queue) (B43_SHM_SH_EDCFQ + \
709 (B43_NR_QOSPARAMS * sizeof(u16) * (queue)))
710 #define B43_QOS_BACKGROUND B43_QOS_PARAMS(0)
711 #define B43_QOS_BESTEFFORT B43_QOS_PARAMS(1)
712 #define B43_QOS_VIDEO B43_QOS_PARAMS(2)
713 #define B43_QOS_VOICE B43_QOS_PARAMS(3)
714
715 /* QOS parameter hardware data structure offsets. */
716 #define B43_NR_QOSPARAMS 16
717 enum {
718 B43_QOSPARAM_TXOP = 0,
719 B43_QOSPARAM_CWMIN,
720 B43_QOSPARAM_CWMAX,
721 B43_QOSPARAM_CWCUR,
722 B43_QOSPARAM_AIFS,
723 B43_QOSPARAM_BSLOTS,
724 B43_QOSPARAM_REGGAP,
725 B43_QOSPARAM_STATUS,
726 };
727
728 /* QOS parameters for a queue. */
729 struct b43_qos_params {
730 /* The QOS parameters */
731 struct ieee80211_tx_queue_params p;
732 };
733
734 struct b43_wl;
735
736 /* The type of the firmware file. */
737 enum b43_firmware_file_type {
738 B43_FWTYPE_PROPRIETARY,
739 B43_FWTYPE_OPENSOURCE,
740 B43_NR_FWTYPES,
741 };
742
743 /* Context data for fetching firmware. */
744 struct b43_request_fw_context {
745 /* The device we are requesting the fw for. */
746 struct b43_wldev *dev;
747 /* a pointer to the firmware object */
748 const struct firmware *blob;
749 /* The type of firmware to request. */
750 enum b43_firmware_file_type req_type;
751 /* Error messages for each firmware type. */
752 char errors[B43_NR_FWTYPES][128];
753 /* Temporary buffer for storing the firmware name. */
754 char fwname[64];
755 /* A fatal error occurred while requesting. Firmware request
756 * can not continue, as any other request will also fail. */
757 int fatal_failure;
758 };
759
760 /* In-memory representation of a cached microcode file. */
761 struct b43_firmware_file {
762 const char *filename;
763 const struct firmware *data;
764 /* Type of the firmware file name. Note that this does only indicate
765 * the type by the firmware name. NOT the file contents.
766 * If you want to check for proprietary vs opensource, use (struct b43_firmware)->opensource
767 * instead! The (struct b43_firmware)->opensource flag is derived from the actual firmware
768 * binary code, not just the filename.
769 */
770 enum b43_firmware_file_type type;
771 };
772
773 enum b43_firmware_hdr_format {
774 B43_FW_HDR_598,
775 B43_FW_HDR_410,
776 B43_FW_HDR_351,
777 };
778
779 /* Pointers to the firmware data and meta information about it. */
780 struct b43_firmware {
781 /* Microcode */
782 struct b43_firmware_file ucode;
783 /* PCM code */
784 struct b43_firmware_file pcm;
785 /* Initial MMIO values for the firmware */
786 struct b43_firmware_file initvals;
787 /* Initial MMIO values for the firmware, band-specific */
788 struct b43_firmware_file initvals_band;
789
790 /* Firmware revision */
791 u16 rev;
792 /* Firmware patchlevel */
793 u16 patch;
794
795 /* Format of header used by firmware */
796 enum b43_firmware_hdr_format hdr_format;
797
798 /* Set to true, if we are using an opensource firmware.
799 * Use this to check for proprietary vs opensource. */
800 bool opensource;
801 /* Set to true, if the core needs a PCM firmware, but
802 * we failed to load one. This is always false for
803 * core rev > 10, as these don't need PCM firmware. */
804 bool pcm_request_failed;
805 };
806
807 enum b43_band {
808 B43_BAND_2G = 0,
809 B43_BAND_5G_LO = 1,
810 B43_BAND_5G_MI = 2,
811 B43_BAND_5G_HI = 3,
812 };
813
814 /* Device (802.11 core) initialization status. */
815 enum {
816 B43_STAT_UNINIT = 0, /* Uninitialized. */
817 B43_STAT_INITIALIZED = 1, /* Initialized, but not started, yet. */
818 B43_STAT_STARTED = 2, /* Up and running. */
819 };
820 #define b43_status(wldev) atomic_read(&(wldev)->__init_status)
821 #define b43_set_status(wldev, stat) do { \
822 atomic_set(&(wldev)->__init_status, (stat)); \
823 smp_wmb(); \
824 } while (0)
825
826 /* Data structure for one wireless device (802.11 core) */
827 struct b43_wldev {
828 struct b43_bus_dev *dev;
829 struct b43_wl *wl;
830 /* a completion event structure needed if this call is asynchronous */
831 struct completion fw_load_complete;
832
833 /* The device initialization status.
834 * Use b43_status() to query. */
835 atomic_t __init_status;
836
837 bool bad_frames_preempt; /* Use "Bad Frames Preemption" (default off) */
838 bool dfq_valid; /* Directed frame queue valid (IBSS PS mode, ATIM) */
839 bool radio_hw_enable; /* saved state of radio hardware enabled state */
840 bool qos_enabled; /* TRUE, if QoS is used. */
841 bool hwcrypto_enabled; /* TRUE, if HW crypto acceleration is enabled. */
842 bool use_pio; /* TRUE if next init should use PIO */
843
844 /* PHY/Radio device. */
845 struct b43_phy phy;
846
847 union {
848 /* DMA engines. */
849 struct b43_dma dma;
850 /* PIO engines. */
851 struct b43_pio pio;
852 };
853 /* Use b43_using_pio_transfers() to check whether we are using
854 * DMA or PIO data transfers. */
855 bool __using_pio_transfers;
856
857 /* Various statistics about the physical device. */
858 struct b43_stats stats;
859
860 /* Reason code of the last interrupt. */
861 u32 irq_reason;
862 u32 dma_reason[6];
863 /* The currently active generic-interrupt mask. */
864 u32 irq_mask;
865
866 /* Link Quality calculation context. */
867 struct b43_noise_calculation noisecalc;
868 /* if > 0 MAC is suspended. if == 0 MAC is enabled. */
869 int mac_suspended;
870
871 /* Periodic tasks */
872 struct delayed_work periodic_work;
873 unsigned int periodic_state;
874
875 struct work_struct restart_work;
876
877 /* encryption/decryption */
878 u16 ktp; /* Key table pointer */
879 struct b43_key key[B43_NR_GROUP_KEYS * 2 + B43_NR_PAIRWISE_KEYS];
880
881 /* Firmware data */
882 struct b43_firmware fw;
883
884 /* Devicelist in struct b43_wl (all 802.11 cores) */
885 struct list_head list;
886
887 /* Debugging stuff follows. */
888 #ifdef CONFIG_B43_DEBUG
889 struct b43_dfsentry *dfsentry;
890 unsigned int irq_count;
891 unsigned int irq_bit_count[32];
892 unsigned int tx_count;
893 unsigned int rx_count;
894 #endif
895 };
896
897 /* Data structure for the WLAN parts (802.11 cores) of the b43 chip. */
898 struct b43_wl {
899 /* Pointer to the active wireless device on this chip */
900 struct b43_wldev *current_dev;
901 /* Pointer to the ieee80211 hardware data structure */
902 struct ieee80211_hw *hw;
903
904 /* Global driver mutex. Every operation must run with this mutex locked. */
905 struct mutex mutex;
906 /* Hard-IRQ spinlock. This lock protects things used in the hard-IRQ
907 * handler, only. This basically is just the IRQ mask register. */
908 spinlock_t hardirq_lock;
909
910 /* Set this if we call ieee80211_register_hw() and check if we call
911 * ieee80211_unregister_hw(). */
912 bool hw_registered;
913
914 /* We can only have one operating interface (802.11 core)
915 * at a time. General information about this interface follows.
916 */
917
918 struct ieee80211_vif *vif;
919 /* The MAC address of the operating interface. */
920 u8 mac_addr[ETH_ALEN];
921 /* Current BSSID */
922 u8 bssid[ETH_ALEN];
923 /* Interface type. (NL80211_IFTYPE_XXX) */
924 int if_type;
925 /* Is the card operating in AP, STA or IBSS mode? */
926 bool operating;
927 /* filter flags */
928 unsigned int filter_flags;
929 /* Stats about the wireless interface */
930 struct ieee80211_low_level_stats ieee_stats;
931
932 #ifdef CONFIG_B43_HWRNG
933 struct hwrng rng;
934 bool rng_initialized;
935 char rng_name[30 + 1];
936 #endif /* CONFIG_B43_HWRNG */
937
938 bool radiotap_enabled;
939 bool radio_enabled;
940
941 /* The beacon we are currently using (AP or IBSS mode). */
942 struct sk_buff *current_beacon;
943 bool beacon0_uploaded;
944 bool beacon1_uploaded;
945 bool beacon_templates_virgin; /* Never wrote the templates? */
946 struct work_struct beacon_update_trigger;
947 spinlock_t beacon_lock;
948
949 /* The current QOS parameters for the 4 queues. */
950 struct b43_qos_params qos_params[B43_QOS_QUEUE_NUM];
951
952 /* Work for adjustment of the transmission power.
953 * This is scheduled when we determine that the actual TX output
954 * power doesn't match what we want. */
955 struct work_struct txpower_adjust_work;
956
957 /* Packet transmit work */
958 struct work_struct tx_work;
959
960 /* Queue of packets to be transmitted. */
961 struct sk_buff_head tx_queue[B43_QOS_QUEUE_NUM];
962
963 /* Flag that implement the queues stopping. */
964 bool tx_queue_stopped[B43_QOS_QUEUE_NUM];
965
966 /* firmware loading work */
967 struct work_struct firmware_load;
968
969 /* The device LEDs. */
970 struct b43_leds leds;
971
972 /* Kmalloc'ed scratch space for PIO TX/RX. Protected by wl->mutex. */
973 u8 pio_scratchspace[118] __attribute__((__aligned__(8)));
974 u8 pio_tailspace[4] __attribute__((__aligned__(8)));
975 };
976
hw_to_b43_wl(struct ieee80211_hw * hw)977 static inline struct b43_wl *hw_to_b43_wl(struct ieee80211_hw *hw)
978 {
979 return hw->priv;
980 }
981
dev_to_b43_wldev(struct device * dev)982 static inline struct b43_wldev *dev_to_b43_wldev(struct device *dev)
983 {
984 struct ssb_device *ssb_dev = dev_to_ssb_dev(dev);
985 return ssb_get_drvdata(ssb_dev);
986 }
987
988 /* Is the device operating in a specified mode (NL80211_IFTYPE_XXX). */
b43_is_mode(struct b43_wl * wl,int type)989 static inline int b43_is_mode(struct b43_wl *wl, int type)
990 {
991 return (wl->operating && wl->if_type == type);
992 }
993
994 /**
995 * b43_current_band - Returns the currently used band.
996 * Returns one of NL80211_BAND_2GHZ and NL80211_BAND_5GHZ.
997 */
b43_current_band(struct b43_wl * wl)998 static inline enum nl80211_band b43_current_band(struct b43_wl *wl)
999 {
1000 return wl->hw->conf.chandef.chan->band;
1001 }
1002
b43_bus_may_powerdown(struct b43_wldev * wldev)1003 static inline int b43_bus_may_powerdown(struct b43_wldev *wldev)
1004 {
1005 return wldev->dev->bus_may_powerdown(wldev->dev);
1006 }
b43_bus_powerup(struct b43_wldev * wldev,bool dynamic_pctl)1007 static inline int b43_bus_powerup(struct b43_wldev *wldev, bool dynamic_pctl)
1008 {
1009 return wldev->dev->bus_powerup(wldev->dev, dynamic_pctl);
1010 }
b43_device_is_enabled(struct b43_wldev * wldev)1011 static inline int b43_device_is_enabled(struct b43_wldev *wldev)
1012 {
1013 return wldev->dev->device_is_enabled(wldev->dev);
1014 }
b43_device_enable(struct b43_wldev * wldev,u32 core_specific_flags)1015 static inline void b43_device_enable(struct b43_wldev *wldev,
1016 u32 core_specific_flags)
1017 {
1018 wldev->dev->device_enable(wldev->dev, core_specific_flags);
1019 }
b43_device_disable(struct b43_wldev * wldev,u32 core_specific_flags)1020 static inline void b43_device_disable(struct b43_wldev *wldev,
1021 u32 core_specific_flags)
1022 {
1023 wldev->dev->device_disable(wldev->dev, core_specific_flags);
1024 }
1025
b43_read16(struct b43_wldev * dev,u16 offset)1026 static inline u16 b43_read16(struct b43_wldev *dev, u16 offset)
1027 {
1028 return dev->dev->read16(dev->dev, offset);
1029 }
1030
b43_write16(struct b43_wldev * dev,u16 offset,u16 value)1031 static inline void b43_write16(struct b43_wldev *dev, u16 offset, u16 value)
1032 {
1033 dev->dev->write16(dev->dev, offset, value);
1034 }
1035
1036 /* To optimize this check for flush_writes on BCM47XX_BCMA only. */
b43_write16f(struct b43_wldev * dev,u16 offset,u16 value)1037 static inline void b43_write16f(struct b43_wldev *dev, u16 offset, u16 value)
1038 {
1039 b43_write16(dev, offset, value);
1040 #if defined(CONFIG_BCM47XX_BCMA)
1041 if (dev->dev->flush_writes)
1042 b43_read16(dev, offset);
1043 #endif
1044 }
1045
b43_maskset16(struct b43_wldev * dev,u16 offset,u16 mask,u16 set)1046 static inline void b43_maskset16(struct b43_wldev *dev, u16 offset, u16 mask,
1047 u16 set)
1048 {
1049 b43_write16(dev, offset, (b43_read16(dev, offset) & mask) | set);
1050 }
1051
b43_read32(struct b43_wldev * dev,u16 offset)1052 static inline u32 b43_read32(struct b43_wldev *dev, u16 offset)
1053 {
1054 return dev->dev->read32(dev->dev, offset);
1055 }
1056
b43_write32(struct b43_wldev * dev,u16 offset,u32 value)1057 static inline void b43_write32(struct b43_wldev *dev, u16 offset, u32 value)
1058 {
1059 dev->dev->write32(dev->dev, offset, value);
1060 }
1061
b43_maskset32(struct b43_wldev * dev,u16 offset,u32 mask,u32 set)1062 static inline void b43_maskset32(struct b43_wldev *dev, u16 offset, u32 mask,
1063 u32 set)
1064 {
1065 b43_write32(dev, offset, (b43_read32(dev, offset) & mask) | set);
1066 }
1067
b43_block_read(struct b43_wldev * dev,void * buffer,size_t count,u16 offset,u8 reg_width)1068 static inline void b43_block_read(struct b43_wldev *dev, void *buffer,
1069 size_t count, u16 offset, u8 reg_width)
1070 {
1071 dev->dev->block_read(dev->dev, buffer, count, offset, reg_width);
1072 }
1073
b43_block_write(struct b43_wldev * dev,const void * buffer,size_t count,u16 offset,u8 reg_width)1074 static inline void b43_block_write(struct b43_wldev *dev, const void *buffer,
1075 size_t count, u16 offset, u8 reg_width)
1076 {
1077 dev->dev->block_write(dev->dev, buffer, count, offset, reg_width);
1078 }
1079
b43_using_pio_transfers(struct b43_wldev * dev)1080 static inline bool b43_using_pio_transfers(struct b43_wldev *dev)
1081 {
1082 return dev->__using_pio_transfers;
1083 }
1084
1085 /* Message printing */
1086 __printf(2, 3) void b43info(struct b43_wl *wl, const char *fmt, ...);
1087 __printf(2, 3) void b43err(struct b43_wl *wl, const char *fmt, ...);
1088 __printf(2, 3) void b43warn(struct b43_wl *wl, const char *fmt, ...);
1089 __printf(2, 3) void b43dbg(struct b43_wl *wl, const char *fmt, ...);
1090
1091
1092 /* A WARN_ON variant that vanishes when b43 debugging is disabled.
1093 * This _also_ evaluates the arg with debugging disabled. */
1094 #if B43_DEBUG
1095 # define B43_WARN_ON(x) WARN_ON(x)
1096 #else
__b43_warn_on_dummy(bool x)1097 static inline bool __b43_warn_on_dummy(bool x) { return x; }
1098 # define B43_WARN_ON(x) __b43_warn_on_dummy(unlikely(!!(x)))
1099 #endif
1100
1101 /* Convert an integer to a Q5.2 value */
1102 #define INT_TO_Q52(i) ((i) << 2)
1103 /* Convert a Q5.2 value to an integer (precision loss!) */
1104 #define Q52_TO_INT(q52) ((q52) >> 2)
1105 /* Macros for printing a value in Q5.2 format */
1106 #define Q52_FMT "%u.%u"
1107 #define Q52_ARG(q52) Q52_TO_INT(q52), ((((q52) & 0x3) * 100) / 4)
1108
1109 #endif /* B43_H_ */
1110