/* * scsi_error.c Copyright (C) 1997 Eric Youngdale * * SCSI error/timeout handling * Initial versions: Eric Youngdale. Based upon conversations with * Leonard Zubkoff and David Miller at Linux Expo, * ideas originating from all over the place. * */ #define __NO_VERSION__ #include #include #include #include #include #include #include #include #include #include #include #include #define __KERNEL_SYSCALLS__ #include #include #include #include #include "scsi.h" #include "hosts.h" #include "constants.h" /* * We must always allow SHUTDOWN_SIGS. Even if we are not a module, * the host drivers that we are using may be loaded as modules, and * when we unload these, we need to ensure that the error handler thread * can be shut down. * * Note - when we unload a module, we send a SIGHUP. We mustn't * enable SIGTERM, as this is how the init shuts things down when you * go to single-user mode. For that matter, init also sends SIGKILL, * so we mustn't enable that one either. We use SIGHUP instead. Other * options would be SIGPWR, I suppose. */ #define SHUTDOWN_SIGS (sigmask(SIGHUP)) #ifdef DEBUG #define SENSE_TIMEOUT SCSI_TIMEOUT #define ABORT_TIMEOUT SCSI_TIMEOUT #define RESET_TIMEOUT SCSI_TIMEOUT #else #define SENSE_TIMEOUT (10*HZ) #define RESET_TIMEOUT (2*HZ) #define ABORT_TIMEOUT (15*HZ) #endif #define STATIC /* * These should *probably* be handled by the host itself. * Since it is allowed to sleep, it probably should. */ #define BUS_RESET_SETTLE_TIME 5*HZ #define HOST_RESET_SETTLE_TIME 10*HZ static const char RCSid[] = "$Header: /mnt/ide/home/eric/CVSROOT/linux/drivers/scsi/scsi_error.c,v 1.10 1997/12/08 04:50:35 eric Exp $"; STATIC int scsi_check_sense(Scsi_Cmnd * SCpnt); STATIC int scsi_request_sense(Scsi_Cmnd *); STATIC void scsi_send_eh_cmnd(Scsi_Cmnd * SCpnt, int timeout); STATIC int scsi_try_to_abort_command(Scsi_Cmnd *, int); STATIC int scsi_test_unit_ready(Scsi_Cmnd *); STATIC int scsi_try_bus_device_reset(Scsi_Cmnd *, int timeout); STATIC int scsi_try_bus_reset(Scsi_Cmnd *); STATIC int scsi_try_host_reset(Scsi_Cmnd *); STATIC int scsi_unit_is_ready(Scsi_Cmnd *); STATIC void scsi_eh_action_done(Scsi_Cmnd *, int); STATIC int scsi_eh_retry_command(Scsi_Cmnd *); STATIC int scsi_eh_completed_normally(Scsi_Cmnd * SCpnt); STATIC void scsi_restart_operations(struct Scsi_Host *); STATIC void scsi_eh_finish_command(Scsi_Cmnd ** SClist, Scsi_Cmnd * SCpnt); /* * Function: scsi_add_timer() * * Purpose: Start timeout timer for a single scsi command. * * Arguments: SCset - command that is about to start running. * timeout - amount of time to allow this command to run. * complete - timeout function to call if timer isn't * canceled. * * Returns: Nothing * * Notes: This should be turned into an inline function. * * More Notes: Each scsi command has it's own timer, and as it is added to * the queue, we set up the timer. When the command completes, * we cancel the timer. Pretty simple, really, especially * compared to the old way of handling this crap. */ void scsi_add_timer(Scsi_Cmnd * SCset, int timeout, void (*complete) (Scsi_Cmnd *)) { SCset->eh_timeout.data = (unsigned long) SCset; SCset->eh_timeout.function = (void (*)(unsigned long)) complete; mod_timer(&SCset->eh_timeout, jiffies + timeout); SCset->done_late = 0; SCSI_LOG_ERROR_RECOVERY(5, printk("Adding timer for command %p at %d (%p)\n", SCset, timeout, complete)); } /* * Function: scsi_delete_timer() * * Purpose: Delete/cancel timer for a given function. * * Arguments: SCset - command that we are canceling timer for. * * Returns: 1 if we were able to detach the timer. 0 if we * blew it, and the timer function has already started * to run. * * Notes: This should be turned into an inline function. */ int scsi_delete_timer(Scsi_Cmnd * SCset) { int rtn; rtn = del_timer(&SCset->eh_timeout); SCSI_LOG_ERROR_RECOVERY(5, printk("Clearing timer for command %p %d\n", SCset, rtn)); SCset->eh_timeout.data = (unsigned long) NULL; SCset->eh_timeout.function = NULL; return rtn; } /* * Function: scsi_times_out() * * Purpose: Timeout function for normal scsi commands.. * * Arguments: SCpnt - command that is timing out. * * Returns: Nothing. * * Notes: We do not need to lock this. There is the potential for * a race only in that the normal completion handling might * run, but if the normal completion function determines * that the timer has already fired, then it mustn't do * anything. */ void scsi_times_out(Scsi_Cmnd * SCpnt) { /* * Notify the low-level code that this operation failed and we are * reposessing the command. */ #ifdef ERIC_neverdef /* * FIXME(eric) * Allow the host adapter to push a queue ordering tag * out to the bus to force the command in question to complete. * If the host wants to do this, then we just restart the timer * for the command. Before we really do this, some real thought * as to the optimum way to handle this should be done. We *do* * need to force ordering every so often to ensure that all requests * do eventually complete, but I am not sure if this is the best way * to actually go about it. * * Better yet, force a sync here, but don't block since we are in an * interrupt. */ if (SCpnt->host->hostt->eh_ordered_queue_tag) { if ((*SCpnt->host->hostt->eh_ordered_queue_tag) (SCpnt)) { scsi_add_timer(SCpnt, SCpnt->internal_timeout, scsi_times_out); return; } } /* * FIXME(eric) - add a second special interface to handle this * case. Ideally that interface can also be used to request * a queu */ if (SCpnt->host->can_queue) { SCpnt->host->hostt->queuecommand(SCpnt, NULL); } #endif /* Set the serial_number_at_timeout to the current serial_number */ SCpnt->serial_number_at_timeout = SCpnt->serial_number; SCpnt->eh_state = FAILED; SCpnt->state = SCSI_STATE_TIMEOUT; SCpnt->owner = SCSI_OWNER_ERROR_HANDLER; SCpnt->host->in_recovery = 1; SCpnt->host->host_failed++; SCSI_LOG_TIMEOUT(3, printk("Command timed out active=%d busy=%d failed=%d\n", atomic_read(&SCpnt->host->host_active), SCpnt->host->host_busy, SCpnt->host->host_failed)); /* * If the host is having troubles, then look to see if this was the last * command that might have failed. If so, wake up the error handler. */ if( SCpnt->host->eh_wait == NULL ) { panic("Error handler thread not present at %p %p %s %d", SCpnt, SCpnt->host, __FILE__, __LINE__); } if (SCpnt->host->host_busy == SCpnt->host->host_failed) { up(SCpnt->host->eh_wait); } } /* * Function scsi_block_when_processing_errors * * Purpose: Prevent more commands from being queued while error recovery * is taking place. * * Arguments: SDpnt - device on which we are performing recovery. * * Returns: FALSE The device was taken offline by error recovery. * TRUE OK to proceed. * * Notes: We block until the host is out of error recovery, and then * check to see whether the host or the device is offline. */ int scsi_block_when_processing_errors(Scsi_Device * SDpnt) { SCSI_SLEEP(&SDpnt->host->host_wait, SDpnt->host->in_recovery); SCSI_LOG_ERROR_RECOVERY(5, printk("Open returning %d\n", SDpnt->online)); return SDpnt->online; } /* * Function: scsi_eh_times_out() * * Purpose: Timeout function for error handling. * * Arguments: SCpnt - command that is timing out. * * Returns: Nothing. * * Notes: During error handling, the kernel thread will be sleeping * waiting for some action to complete on the device. Our only * job is to record that it timed out, and to wake up the * thread. */ STATIC void scsi_eh_times_out(Scsi_Cmnd * SCpnt) { SCpnt->eh_state = SCSI_STATE_TIMEOUT; SCSI_LOG_ERROR_RECOVERY(5, printk("In scsi_eh_times_out %p\n", SCpnt)); if (SCpnt->host->eh_action != NULL) up(SCpnt->host->eh_action); else printk("Missing scsi error handler thread\n"); } /* * Function: scsi_eh_done() * * Purpose: Completion function for error handling. * * Arguments: SCpnt - command that is timing out. * * Returns: Nothing. * * Notes: During error handling, the kernel thread will be sleeping * waiting for some action to complete on the device. Our only * job is to record that the action completed, and to wake up the * thread. */ STATIC void scsi_eh_done(Scsi_Cmnd * SCpnt) { int rtn; /* * If the timeout handler is already running, then just set the * flag which says we finished late, and return. We have no * way of stopping the timeout handler from running, so we must * always defer to it. */ rtn = del_timer(&SCpnt->eh_timeout); if (!rtn) { SCpnt->done_late = 1; return; } SCpnt->request.rq_status = RQ_SCSI_DONE; SCpnt->owner = SCSI_OWNER_ERROR_HANDLER; SCpnt->eh_state = SUCCESS; SCSI_LOG_ERROR_RECOVERY(5, printk("In eh_done %p result:%x\n", SCpnt, SCpnt->result)); if (SCpnt->host->eh_action != NULL) up(SCpnt->host->eh_action); } /* * Function: scsi_eh_action_done() * * Purpose: Completion function for error handling. * * Arguments: SCpnt - command that is timing out. * answer - boolean that indicates whether operation succeeded. * * Returns: Nothing. * * Notes: This callback is only used for abort and reset operations. */ STATIC void scsi_eh_action_done(Scsi_Cmnd * SCpnt, int answer) { SCpnt->request.rq_status = RQ_SCSI_DONE; SCpnt->owner = SCSI_OWNER_ERROR_HANDLER; SCpnt->eh_state = (answer ? SUCCESS : FAILED); if (SCpnt->host->eh_action != NULL) up(SCpnt->host->eh_action); } /* * Function: scsi_sense_valid() * * Purpose: Determine whether a host has automatically obtained sense * information or not. If we have it, then give a recommendation * as to what we should do next. */ int scsi_sense_valid(Scsi_Cmnd * SCpnt) { if (((SCpnt->sense_buffer[0] & 0x70) >> 4) != 7) { return FALSE; } return TRUE; } /* * Function: scsi_eh_retry_command() * * Purpose: Retry the original command * * Returns: SUCCESS - we were able to get the sense data. * FAILED - we were not able to get the sense data. * * Notes: This function will *NOT* return until the command either * times out, or it completes. */ STATIC int scsi_eh_retry_command(Scsi_Cmnd * SCpnt) { memcpy((void *) SCpnt->cmnd, (void *) SCpnt->data_cmnd, sizeof(SCpnt->data_cmnd)); SCpnt->request_buffer = SCpnt->buffer; SCpnt->request_bufflen = SCpnt->bufflen; SCpnt->use_sg = SCpnt->old_use_sg; SCpnt->cmd_len = SCpnt->old_cmd_len; SCpnt->sc_data_direction = SCpnt->sc_old_data_direction; SCpnt->underflow = SCpnt->old_underflow; scsi_send_eh_cmnd(SCpnt, SCpnt->timeout_per_command); /* * Hey, we are done. Let's look to see what happened. */ return SCpnt->eh_state; } /* * Function: scsi_request_sense() * * Purpose: Request sense data from a particular target. * * Returns: SUCCESS - we were able to get the sense data. * FAILED - we were not able to get the sense data. * * Notes: Some hosts automatically obtain this information, others * require that we obtain it on our own. * * This function will *NOT* return until the command either * times out, or it completes. */ STATIC int scsi_request_sense(Scsi_Cmnd * SCpnt) { static unsigned char generic_sense[6] = {REQUEST_SENSE, 0, 0, 0, 255, 0}; unsigned char scsi_result0[256], *scsi_result = NULL; int saved_result; int saved_resid; ASSERT_LOCK(&io_request_lock, 0); memcpy((void *) SCpnt->cmnd, (void *) generic_sense, sizeof(generic_sense)); if (SCpnt->device->scsi_level <= SCSI_2) SCpnt->cmnd[1] = SCpnt->lun << 5; scsi_result = (!SCpnt->host->hostt->unchecked_isa_dma) ? &scsi_result0[0] : kmalloc(512, GFP_ATOMIC | GFP_DMA); if (scsi_result == NULL) { printk("cannot allocate scsi_result in scsi_request_sense.\n"); return FAILED; } /* * Zero the sense buffer. Some host adapters automatically always request * sense, so it is not a good idea that SCpnt->request_buffer and * SCpnt->sense_buffer point to the same address (DB). * 0 is not a valid sense code. */ memset((void *) SCpnt->sense_buffer, 0, sizeof(SCpnt->sense_buffer)); memset((void *) scsi_result, 0, 256); saved_result = SCpnt->result; saved_resid = SCpnt->resid; SCpnt->request_buffer = scsi_result; SCpnt->request_bufflen = 256; SCpnt->use_sg = 0; SCpnt->cmd_len = COMMAND_SIZE(SCpnt->cmnd[0]); SCpnt->sc_data_direction = SCSI_DATA_READ; SCpnt->underflow = 0; scsi_send_eh_cmnd(SCpnt, SENSE_TIMEOUT); /* Last chance to have valid sense data */ if (!scsi_sense_valid(SCpnt)) memcpy((void *) SCpnt->sense_buffer, SCpnt->request_buffer, sizeof(SCpnt->sense_buffer)); if (scsi_result != &scsi_result0[0] && scsi_result != NULL) kfree(scsi_result); /* * When we eventually call scsi_finish, we really wish to complete * the original request, so let's restore the original data. (DB) */ memcpy((void *) SCpnt->cmnd, (void *) SCpnt->data_cmnd, sizeof(SCpnt->data_cmnd)); SCpnt->result = saved_result; SCpnt->resid = saved_resid; SCpnt->request_buffer = SCpnt->buffer; SCpnt->request_bufflen = SCpnt->bufflen; SCpnt->use_sg = SCpnt->old_use_sg; SCpnt->cmd_len = SCpnt->old_cmd_len; SCpnt->sc_data_direction = SCpnt->sc_old_data_direction; SCpnt->underflow = SCpnt->old_underflow; /* * Hey, we are done. Let's look to see what happened. */ return SCpnt->eh_state; } /* * Function: scsi_test_unit_ready() * * Purpose: Run test unit ready command to see if the device is talking to us or not. * */ STATIC int scsi_test_unit_ready(Scsi_Cmnd * SCpnt) { static unsigned char tur_command[6] = {TEST_UNIT_READY, 0, 0, 0, 0, 0}; int saved_resid; memcpy((void *) SCpnt->cmnd, (void *) tur_command, sizeof(tur_command)); if (SCpnt->device->scsi_level <= SCSI_2) SCpnt->cmnd[1] = SCpnt->lun << 5; /* * Zero the sense buffer. The SCSI spec mandates that any * untransferred sense data should be interpreted as being zero. */ memset((void *) SCpnt->sense_buffer, 0, sizeof(SCpnt->sense_buffer)); saved_resid = SCpnt->resid; SCpnt->request_buffer = NULL; SCpnt->request_bufflen = 0; SCpnt->use_sg = 0; SCpnt->cmd_len = COMMAND_SIZE(SCpnt->cmnd[0]); SCpnt->underflow = 0; SCpnt->sc_data_direction = SCSI_DATA_NONE; scsi_send_eh_cmnd(SCpnt, SENSE_TIMEOUT); /* * When we eventually call scsi_finish, we really wish to complete * the original request, so let's restore the original data. (DB) */ memcpy((void *) SCpnt->cmnd, (void *) SCpnt->data_cmnd, sizeof(SCpnt->data_cmnd)); SCpnt->resid = saved_resid; SCpnt->request_buffer = SCpnt->buffer; SCpnt->request_bufflen = SCpnt->bufflen; SCpnt->use_sg = SCpnt->old_use_sg; SCpnt->cmd_len = SCpnt->old_cmd_len; SCpnt->sc_data_direction = SCpnt->sc_old_data_direction; SCpnt->underflow = SCpnt->old_underflow; /* * Hey, we are done. Let's look to see what happened. */ SCSI_LOG_ERROR_RECOVERY(3, printk("scsi_test_unit_ready: SCpnt %p eh_state %x\n", SCpnt, SCpnt->eh_state)); return SCpnt->eh_state; } /* * This would normally need to get the IO request lock, * but as it doesn't actually touch anything that needs * to be locked we can avoid the lock here.. */ STATIC void scsi_sleep_done(struct semaphore *sem) { if (sem != NULL) { up(sem); } } void scsi_sleep(int timeout) { DECLARE_MUTEX_LOCKED(sem); struct timer_list timer; init_timer(&timer); timer.data = (unsigned long) &sem; timer.expires = jiffies + timeout; timer.function = (void (*)(unsigned long)) scsi_sleep_done; SCSI_LOG_ERROR_RECOVERY(5, printk("Sleeping for timer tics %d\n", timeout)); add_timer(&timer); down(&sem); del_timer(&timer); } /* * Function: scsi_send_eh_cmnd * * Purpose: Send a command out to a device as part of error recovery. * * Notes: The initialization of the structures is quite a bit different * in this case, and furthermore, there is a different completion * handler. */ STATIC void scsi_send_eh_cmnd(Scsi_Cmnd * SCpnt, int timeout) { unsigned long flags; struct Scsi_Host *host; ASSERT_LOCK(&io_request_lock, 0); host = SCpnt->host; retry: /* * We will use a queued command if possible, otherwise we will emulate the * queuing and calling of completion function ourselves. */ SCpnt->owner = SCSI_OWNER_LOWLEVEL; if (host->can_queue) { DECLARE_MUTEX_LOCKED(sem); SCpnt->eh_state = SCSI_STATE_QUEUED; scsi_add_timer(SCpnt, timeout, scsi_eh_times_out); /* * Set up the semaphore so we wait for the command to complete. */ SCpnt->host->eh_action = &sem; SCpnt->request.rq_status = RQ_SCSI_BUSY; spin_lock_irqsave(&io_request_lock, flags); host->hostt->queuecommand(SCpnt, scsi_eh_done); spin_unlock_irqrestore(&io_request_lock, flags); down(&sem); SCpnt->host->eh_action = NULL; /* * See if timeout. If so, tell the host to forget about it. * In other words, we don't want a callback any more. */ if (SCpnt->eh_state == SCSI_STATE_TIMEOUT) { SCpnt->owner = SCSI_OWNER_LOWLEVEL; /* * As far as the low level driver is * concerned, this command is still active, so * we must give the low level driver a chance * to abort it. (DB) * * FIXME(eric) - we are not tracking whether we could * abort a timed out command or not. Not sure how * we should treat them differently anyways. */ spin_lock_irqsave(&io_request_lock, flags); if (SCpnt->host->hostt->eh_abort_handler) SCpnt->host->hostt->eh_abort_handler(SCpnt); spin_unlock_irqrestore(&io_request_lock, flags); SCpnt->request.rq_status = RQ_SCSI_DONE; SCpnt->owner = SCSI_OWNER_ERROR_HANDLER; SCpnt->eh_state = FAILED; } SCSI_LOG_ERROR_RECOVERY(5, printk("send_eh_cmnd: %p eh_state:%x\n", SCpnt, SCpnt->eh_state)); } else { int temp; /* * We damn well had better never use this code. There is no timeout * protection here, since we would end up waiting in the actual low * level driver, we don't know how to wake it up. */ spin_lock_irqsave(&io_request_lock, flags); temp = host->hostt->command(SCpnt); spin_unlock_irqrestore(&io_request_lock, flags); SCpnt->result = temp; /* Fall through to code below to examine status. */ SCpnt->eh_state = SUCCESS; } /* * Now examine the actual status codes to see whether the command actually * did complete normally. */ if (SCpnt->eh_state == SUCCESS) { int ret = scsi_eh_completed_normally(SCpnt); SCSI_LOG_ERROR_RECOVERY(3, printk("scsi_send_eh_cmnd: scsi_eh_completed_normally %x\n", ret)); switch (ret) { case SUCCESS: SCpnt->eh_state = SUCCESS; break; case NEEDS_RETRY: if ((++SCpnt->retries) < SCpnt->allowed) goto retry; SCpnt->eh_state = SUCCESS; break; case FAILED: default: SCpnt->eh_state = FAILED; break; } } else { SCpnt->eh_state = FAILED; } } /* * Function: scsi_unit_is_ready() * * Purpose: Called after TEST_UNIT_READY is run, to test to see if * the unit responded in a way that indicates it is ready. */ STATIC int scsi_unit_is_ready(Scsi_Cmnd * SCpnt) { if (SCpnt->result) { if (((driver_byte(SCpnt->result) & DRIVER_SENSE) || (status_byte(SCpnt->result) & CHECK_CONDITION)) && ((SCpnt->sense_buffer[0] & 0x70) >> 4) == 7) { if (((SCpnt->sense_buffer[2] & 0xf) != NOT_READY) && ((SCpnt->sense_buffer[2] & 0xf) != UNIT_ATTENTION) && ((SCpnt->sense_buffer[2] & 0xf) != ILLEGAL_REQUEST)) { return 0; } } } return 1; } /* * Function: scsi_eh_finish_command * * Purpose: Handle a command that we are finished with WRT error handling. * * Arguments: SClist - pointer to list into which we are putting completed commands. * SCpnt - command that is completing * * Notes: We don't want to use the normal command completion while we are * are still handling errors - it may cause other commands to be queued, * and that would disturb what we are doing. Thus we really want to keep * a list of pending commands for final completion, and once we * are ready to leave error handling we handle completion for real. */ STATIC void scsi_eh_finish_command(Scsi_Cmnd ** SClist, Scsi_Cmnd * SCpnt) { SCpnt->state = SCSI_STATE_BHQUEUE; SCpnt->bh_next = *SClist; /* * Set this back so that the upper level can correctly free up * things. */ SCpnt->use_sg = SCpnt->old_use_sg; SCpnt->sc_data_direction = SCpnt->sc_old_data_direction; SCpnt->underflow = SCpnt->old_underflow; *SClist = SCpnt; } /* * Function: scsi_try_to_abort_command * * Purpose: Ask host adapter to abort a running command. * * Returns: FAILED Operation failed or not supported. * SUCCESS Succeeded. * * Notes: This function will not return until the user's completion * function has been called. There is no timeout on this * operation. If the author of the low-level driver wishes * this operation to be timed, they can provide this facility * themselves. Helper functions in scsi_error.c can be supplied * to make this easier to do. * * Notes: It may be possible to combine this with all of the reset * handling to eliminate a lot of code duplication. I don't * know what makes more sense at the moment - this is just a * prototype. */ STATIC int scsi_try_to_abort_command(Scsi_Cmnd * SCpnt, int timeout) { int rtn; unsigned long flags; SCpnt->eh_state = FAILED; /* Until we come up with something better */ if (SCpnt->host->hostt->eh_abort_handler == NULL) { return FAILED; } /* * scsi_done was called just after the command timed out and before * we had a chance to process it. (DB) */ if (SCpnt->serial_number == 0) return SUCCESS; SCpnt->owner = SCSI_OWNER_LOWLEVEL; spin_lock_irqsave(&io_request_lock, flags); rtn = SCpnt->host->hostt->eh_abort_handler(SCpnt); spin_unlock_irqrestore(&io_request_lock, flags); return rtn; } /* * Function: scsi_try_bus_device_reset * * Purpose: Ask host adapter to perform a bus device reset for a given * device. * * Returns: FAILED Operation failed or not supported. * SUCCESS Succeeded. * * Notes: There is no timeout for this operation. If this operation is * unreliable for a given host, then the host itself needs to put a * timer on it, and set the host back to a consistent state prior * to returning. */ STATIC int scsi_try_bus_device_reset(Scsi_Cmnd * SCpnt, int timeout) { unsigned long flags; int rtn; SCpnt->eh_state = FAILED; /* Until we come up with something better */ if (SCpnt->host->hostt->eh_device_reset_handler == NULL) { return FAILED; } SCpnt->owner = SCSI_OWNER_LOWLEVEL; spin_lock_irqsave(&io_request_lock, flags); rtn = SCpnt->host->hostt->eh_device_reset_handler(SCpnt); spin_unlock_irqrestore(&io_request_lock, flags); if (rtn == SUCCESS) SCpnt->eh_state = SUCCESS; return SCpnt->eh_state; } /* * Function: scsi_try_bus_reset * * Purpose: Ask host adapter to perform a bus reset for a host. * * Returns: FAILED Operation failed or not supported. * SUCCESS Succeeded. * * Notes: */ STATIC int scsi_try_bus_reset(Scsi_Cmnd * SCpnt) { unsigned long flags; int rtn; SCpnt->eh_state = FAILED; /* Until we come up with something better */ SCpnt->owner = SCSI_OWNER_LOWLEVEL; SCpnt->serial_number_at_timeout = SCpnt->serial_number; if (SCpnt->host->hostt->eh_bus_reset_handler == NULL) { return FAILED; } spin_lock_irqsave(&io_request_lock, flags); rtn = SCpnt->host->hostt->eh_bus_reset_handler(SCpnt); spin_unlock_irqrestore(&io_request_lock, flags); if (rtn == SUCCESS) SCpnt->eh_state = SUCCESS; /* * If we had a successful bus reset, mark the command blocks to expect * a condition code of unit attention. */ scsi_sleep(BUS_RESET_SETTLE_TIME); if (SCpnt->eh_state == SUCCESS) { Scsi_Device *SDloop; for (SDloop = SCpnt->host->host_queue; SDloop; SDloop = SDloop->next) { if (SCpnt->channel == SDloop->channel) { SDloop->was_reset = 1; SDloop->expecting_cc_ua = 1; } } } return SCpnt->eh_state; } /* * Function: scsi_try_host_reset * * Purpose: Ask host adapter to reset itself, and the bus. * * Returns: FAILED Operation failed or not supported. * SUCCESS Succeeded. * * Notes: */ STATIC int scsi_try_host_reset(Scsi_Cmnd * SCpnt) { unsigned long flags; int rtn; SCpnt->eh_state = FAILED; /* Until we come up with something better */ SCpnt->owner = SCSI_OWNER_LOWLEVEL; SCpnt->serial_number_at_timeout = SCpnt->serial_number; if (SCpnt->host->hostt->eh_host_reset_handler == NULL) { return FAILED; } spin_lock_irqsave(&io_request_lock, flags); rtn = SCpnt->host->hostt->eh_host_reset_handler(SCpnt); spin_unlock_irqrestore(&io_request_lock, flags); if (rtn == SUCCESS) SCpnt->eh_state = SUCCESS; /* * If we had a successful host reset, mark the command blocks to expect * a condition code of unit attention. */ scsi_sleep(HOST_RESET_SETTLE_TIME); if (SCpnt->eh_state == SUCCESS) { Scsi_Device *SDloop; for (SDloop = SCpnt->host->host_queue; SDloop; SDloop = SDloop->next) { SDloop->was_reset = 1; SDloop->expecting_cc_ua = 1; } } return SCpnt->eh_state; } /* * Function: scsi_decide_disposition * * Purpose: Examine a command block that has come back from the low-level * and figure out what to do next. * * Returns: SUCCESS - pass on to upper level. * FAILED - pass on to error handler thread. * RETRY - command should be retried. * SOFTERR - command succeeded, but we need to log * a soft error. * * Notes: This is *ONLY* called when we are examining the status * after sending out the actual data command. Any commands * that are queued for error recovery (i.e. TEST_UNIT_READY) * do *NOT* come through here. * * NOTE - When this routine returns FAILED, it means the error * handler thread is woken. In cases where the error code * indicates an error that doesn't require the error handler * thread (i.e. we don't need to abort/reset), then this function * should return SUCCESS. */ int scsi_decide_disposition(Scsi_Cmnd * SCpnt) { int rtn; /* * If the device is offline, then we clearly just pass the result back * up to the top level. */ if (SCpnt->device->online == FALSE) { SCSI_LOG_ERROR_RECOVERY(5, printk("scsi_error.c: device offline - report as SUCCESS\n")); return SUCCESS; } /* * First check the host byte, to see if there is anything in there * that would indicate what we need to do. */ switch (host_byte(SCpnt->result)) { case DID_PASSTHROUGH: /* * No matter what, pass this through to the upper layer. * Nuke this special code so that it looks like we are saying * DID_OK. */ SCpnt->result &= 0xff00ffff; return SUCCESS; case DID_OK: /* * Looks good. Drop through, and check the next byte. */ break; case DID_NO_CONNECT: case DID_BAD_TARGET: case DID_ABORT: /* * Note - this means that we just report the status back to the * top level driver, not that we actually think that it indicates * success. */ return SUCCESS; /* * When the low level driver returns DID_SOFT_ERROR, * it is responsible for keeping an internal retry counter * in order to avoid endless loops (DB) * * Actually this is a bug in this function here. We should * be mindful of the maximum number of retries specified * and not get stuck in a loop. */ case DID_SOFT_ERROR: goto maybe_retry; case DID_ERROR: if (msg_byte(SCpnt->result) == COMMAND_COMPLETE && status_byte(SCpnt->result) == RESERVATION_CONFLICT) /* * execute reservation conflict processing code * lower down */ break; /* FALLTHROUGH */ case DID_BUS_BUSY: case DID_PARITY: goto maybe_retry; case DID_TIME_OUT: /* * When we scan the bus, we get timeout messages for * these commands if there is no device available. * Other hosts report DID_NO_CONNECT for the same thing. */ if ((SCpnt->cmnd[0] == TEST_UNIT_READY || SCpnt->cmnd[0] == INQUIRY)) { return SUCCESS; } else { return FAILED; } case DID_RESET: /* * In the normal case where we haven't initiated a reset, this is * a failure. */ if (SCpnt->flags & IS_RESETTING) { SCpnt->flags &= ~IS_RESETTING; goto maybe_retry; } return SUCCESS; default: return FAILED; } /* * Next, check the message byte. */ if (msg_byte(SCpnt->result) != COMMAND_COMPLETE) { return FAILED; } /* * Now, check the status byte to see if this indicates anything special. */ switch (status_byte(SCpnt->result)) { case QUEUE_FULL: /* * The case of trying to send too many commands to a tagged queueing * device. */ return ADD_TO_MLQUEUE; case GOOD: case COMMAND_TERMINATED: return SUCCESS; case CHECK_CONDITION: rtn = scsi_check_sense(SCpnt); if (rtn == NEEDS_RETRY) { goto maybe_retry; } return rtn; case CONDITION_GOOD: case INTERMEDIATE_GOOD: case INTERMEDIATE_C_GOOD: /* * Who knows? FIXME(eric) */ return SUCCESS; case BUSY: goto maybe_retry; case RESERVATION_CONFLICT: printk("scsi%d (%d,%d,%d) : RESERVATION CONFLICT\n", SCpnt->host->host_no, SCpnt->channel, SCpnt->device->id, SCpnt->device->lun); return SUCCESS; /* causes immediate I/O error */ default: return FAILED; } return FAILED; maybe_retry: if ((++SCpnt->retries) < SCpnt->allowed) { return NEEDS_RETRY; } else { /* * No more retries - report this one back to upper level. */ return SUCCESS; } } /* * Function: scsi_eh_completed_normally * * Purpose: Examine a command block that has come back from the low-level * and figure out what to do next. * * Returns: SUCCESS - pass on to upper level. * FAILED - pass on to error handler thread. * RETRY - command should be retried. * SOFTERR - command succeeded, but we need to log * a soft error. * * Notes: This is *ONLY* called when we are examining the status * of commands queued during error recovery. The main * difference here is that we don't allow for the possibility * of retries here, and we are a lot more restrictive about what * we consider acceptable. */ STATIC int scsi_eh_completed_normally(Scsi_Cmnd * SCpnt) { /* * First check the host byte, to see if there is anything in there * that would indicate what we need to do. */ if (host_byte(SCpnt->result) == DID_RESET) { if (SCpnt->flags & IS_RESETTING) { /* * OK, this is normal. We don't know whether in fact the * command in question really needs to be rerun or not - * if this was the original data command then the answer is yes, * otherwise we just flag it as success. */ SCpnt->flags &= ~IS_RESETTING; return NEEDS_RETRY; } /* * Rats. We are already in the error handler, so we now get to try * and figure out what to do next. If the sense is valid, we have * a pretty good idea of what to do. If not, we mark it as failed. */ return scsi_check_sense(SCpnt); } if (host_byte(SCpnt->result) != DID_OK) { return FAILED; } /* * Next, check the message byte. */ if (msg_byte(SCpnt->result) != COMMAND_COMPLETE) { return FAILED; } /* * Now, check the status byte to see if this indicates anything special. */ switch (status_byte(SCpnt->result)) { case GOOD: case COMMAND_TERMINATED: return SUCCESS; case CHECK_CONDITION: return scsi_check_sense(SCpnt); case CONDITION_GOOD: case INTERMEDIATE_GOOD: case INTERMEDIATE_C_GOOD: /* * Who knows? FIXME(eric) */ return SUCCESS; case BUSY: case QUEUE_FULL: case RESERVATION_CONFLICT: default: return FAILED; } return FAILED; } /* * Function: scsi_check_sense * * Purpose: Examine sense information - give suggestion as to what * we should do with it. */ STATIC int scsi_check_sense(Scsi_Cmnd * SCpnt) { if (!scsi_sense_valid(SCpnt)) { return FAILED; } if (SCpnt->sense_buffer[2] & 0xe0) return SUCCESS; switch (SCpnt->sense_buffer[2] & 0xf) { case NO_SENSE: return SUCCESS; case RECOVERED_ERROR: return /* SOFT_ERROR */ SUCCESS; case ABORTED_COMMAND: return NEEDS_RETRY; case NOT_READY: case UNIT_ATTENTION: /* * If we are expecting a CC/UA because of a bus reset that we * performed, treat this just as a retry. Otherwise this is * information that we should pass up to the upper-level driver * so that we can deal with it there. */ if (SCpnt->device->expecting_cc_ua) { SCpnt->device->expecting_cc_ua = 0; return NEEDS_RETRY; } /* * If the device is in the process of becoming ready, we * should retry. */ if ((SCpnt->sense_buffer[12] == 0x04) && (SCpnt->sense_buffer[13] == 0x01)) { return NEEDS_RETRY; } return SUCCESS; /* these three are not supported */ case COPY_ABORTED: case VOLUME_OVERFLOW: case MISCOMPARE: return SUCCESS; case MEDIUM_ERROR: return NEEDS_RETRY; case ILLEGAL_REQUEST: case BLANK_CHECK: case DATA_PROTECT: case HARDWARE_ERROR: default: return SUCCESS; } } /* * Function: scsi_restart_operations * * Purpose: Restart IO operations to the specified host. * * Arguments: host - host that we are restarting * * Lock status: Assumed that locks are not held upon entry. * * Returns: Nothing * * Notes: When we entered the error handler, we blocked all further * I/O to this device. We need to 'reverse' this process. */ STATIC void scsi_restart_operations(struct Scsi_Host *host) { Scsi_Device *SDpnt; unsigned long flags; ASSERT_LOCK(&io_request_lock, 0); /* * Next free up anything directly waiting upon the host. This will be * requests for character device operations, and also for ioctls to queued * block devices. */ SCSI_LOG_ERROR_RECOVERY(5, printk("scsi_error.c: Waking up host to restart\n")); wake_up(&host->host_wait); /* * Finally we need to re-initiate requests that may be pending. We will * have had everything blocked while error handling is taking place, and * now that error recovery is done, we will need to ensure that these * requests are started. */ spin_lock_irqsave(&io_request_lock, flags); for (SDpnt = host->host_queue; SDpnt; SDpnt = SDpnt->next) { request_queue_t *q; if ((host->can_queue > 0 && (host->host_busy >= host->can_queue)) || (host->host_blocked) || (host->host_self_blocked) || (SDpnt->device_blocked)) { break; } q = &SDpnt->request_queue; q->request_fn(q); } spin_unlock_irqrestore(&io_request_lock, flags); } /* * Function: scsi_unjam_host * * Purpose: Attempt to fix a host which has a command that failed for * some reason. * * Arguments: host - host that needs unjamming. * * Returns: Nothing * * Notes: When we come in here, we *know* that all commands on the * bus have either completed, failed or timed out. We also * know that no further commands are being sent to the host, * so things are relatively quiet and we have freedom to * fiddle with things as we wish. * * Additional note: This is only the *default* implementation. It is possible * for individual drivers to supply their own version of this * function, and if the maintainer wishes to do this, it is * strongly suggested that this function be taken as a template * and modified. This function was designed to correctly handle * problems for about 95% of the different cases out there, and * it should always provide at least a reasonable amount of error * recovery. * * Note3: Any command marked 'FAILED' or 'TIMEOUT' must eventually * have scsi_finish_command() called for it. We do all of * the retry stuff here, so when we restart the host after we * return it should have an empty queue. */ STATIC int scsi_unjam_host(struct Scsi_Host *host) { int devices_failed; int numfailed; int ourrtn; int rtn = FALSE; int result; Scsi_Cmnd *SCloop; Scsi_Cmnd *SCpnt; Scsi_Device *SDpnt; Scsi_Device *SDloop; Scsi_Cmnd *SCdone; int timed_out; ASSERT_LOCK(&io_request_lock, 0); SCdone = NULL; /* * First, protect against any sort of race condition. If any of the outstanding * commands are in states that indicate that we are not yet blocked (i.e. we are * not in a quiet state) then we got woken up in error. If we ever end up here, * we need to re-examine some of the assumptions. */ for (SDpnt = host->host_queue; SDpnt; SDpnt = SDpnt->next) { for (SCpnt = SDpnt->device_queue; SCpnt; SCpnt = SCpnt->next) { if (SCpnt->state == SCSI_STATE_FAILED || SCpnt->state == SCSI_STATE_TIMEOUT || SCpnt->state == SCSI_STATE_INITIALIZING || SCpnt->state == SCSI_STATE_UNUSED) { continue; } /* * Rats. Something is still floating around out there. This could * be the result of the fact that the upper level drivers are still frobbing * commands that might have succeeded. There are two outcomes. One is that * the command block will eventually be freed, and the other one is that * the command will be queued and will be finished along the way. */ SCSI_LOG_ERROR_RECOVERY(1, printk("Error handler prematurely woken - commands still active (%p %x %d)\n", SCpnt, SCpnt->state, SCpnt->target)); /* * panic("SCSI Error handler woken too early\n"); * * This is no longer a problem, since now the code cares only about * SCSI_STATE_TIMEOUT and SCSI_STATE_FAILED. * Other states are useful only to release active commands when devices are * set offline. If (host->host_active == host->host_busy) we can safely assume * that there are no commands in state other then TIMEOUT od FAILED. (DB) * * FIXME: * It is not easy to release correctly commands according to their state when * devices are set offline, when the state is neither TIMEOUT nor FAILED. * When a device is set offline, we can have some command with * rq_status=RQ_SCSY_BUSY, owner=SCSI_STATE_HIGHLEVEL, * state=SCSI_STATE_INITIALIZING and the driver module cannot be released. * (DB, 17 May 1998) */ } } /* * Next, see if we need to request sense information. if so, * then get it now, so we have a better idea of what to do. * FIXME(eric) this has the unfortunate side effect that if a host * adapter does not automatically request sense information, that we end * up shutting it down before we request it. All hosts should be doing this * anyways, so for now all I have to say is tough noogies if you end up in here. * On second thought, this is probably a good idea. We *really* want to give * authors an incentive to automatically request this. */ SCSI_LOG_ERROR_RECOVERY(3, printk("scsi_unjam_host: Checking to see if we need to request sense\n")); for (SDpnt = host->host_queue; SDpnt; SDpnt = SDpnt->next) { for (SCpnt = SDpnt->device_queue; SCpnt; SCpnt = SCpnt->next) { recheck_sense_valid: if (SCpnt->state != SCSI_STATE_FAILED || scsi_sense_valid(SCpnt)) { continue; } SCSI_LOG_ERROR_RECOVERY(2, printk("scsi_unjam_host: Requesting sense for %d\n", SCpnt->target)); rtn = scsi_request_sense(SCpnt); if (rtn != SUCCESS) { continue; } SCSI_LOG_ERROR_RECOVERY(3, printk("Sense requested for %p - result %x\n", SCpnt, SCpnt->result)); SCSI_LOG_ERROR_RECOVERY(3, print_sense("bh", SCpnt)); result = scsi_decide_disposition(SCpnt); /* * If the result was normal, then just pass it along to the * upper level. */ if (result == SUCCESS) { SCpnt->host->host_failed--; scsi_eh_finish_command(&SCdone, SCpnt); } if (result != NEEDS_RETRY) { continue; } /* * We only come in here if we want to retry a * command. The test to see whether the command * should be retried should be keeping track of the * number of tries, so we don't end up looping, of * course. */ SCpnt->state = NEEDS_RETRY; rtn = scsi_eh_retry_command(SCpnt); if (rtn != SUCCESS) { SCpnt->state = SCSI_STATE_FAILED; goto recheck_sense_valid; } /* * We eventually hand this one back to the top level. */ SCpnt->host->host_failed--; scsi_eh_finish_command(&SCdone, SCpnt); } } /* * Go through the list of commands and figure out where we stand and how bad things * really are. */ numfailed = 0; timed_out = 0; devices_failed = 0; for (SDpnt = host->host_queue; SDpnt; SDpnt = SDpnt->next) { unsigned int device_error = 0; for (SCpnt = SDpnt->device_queue; SCpnt; SCpnt = SCpnt->next) { if (SCpnt->state == SCSI_STATE_FAILED) { SCSI_LOG_ERROR_RECOVERY(5, printk("Command to ID %d failed\n", SCpnt->target)); numfailed++; device_error++; } if (SCpnt->state == SCSI_STATE_TIMEOUT) { SCSI_LOG_ERROR_RECOVERY(5, printk("Command to ID %d timedout\n", SCpnt->target)); timed_out++; device_error++; } } if (device_error > 0) { devices_failed++; } } SCSI_LOG_ERROR_RECOVERY(2, printk("Total of %d+%d commands on %d devices require eh work\n", numfailed, timed_out, devices_failed)); if (host->host_failed == 0) { ourrtn = TRUE; goto leave; } /* * Next, try and see whether or not it makes sense to try and abort * the running command. This only works out to be the case if we have * one command that has timed out. If the command simply failed, it * makes no sense to try and abort the command, since as far as the * host adapter is concerned, it isn't running. */ SCSI_LOG_ERROR_RECOVERY(3, printk("scsi_unjam_host: Checking to see if we want to try abort\n")); for (SDpnt = host->host_queue; SDpnt; SDpnt = SDpnt->next) { for (SCloop = SDpnt->device_queue; SCloop; SCloop = SCloop->next) { if (SCloop->state != SCSI_STATE_TIMEOUT) { continue; } rtn = scsi_try_to_abort_command(SCloop, ABORT_TIMEOUT); if (rtn == SUCCESS) { rtn = scsi_test_unit_ready(SCloop); if (rtn == SUCCESS && scsi_unit_is_ready(SCloop)) { rtn = scsi_eh_retry_command(SCloop); if (rtn == SUCCESS) { SCloop->host->host_failed--; scsi_eh_finish_command(&SCdone, SCloop); } } } } } /* * If we have corrected all of the problems, then we are done. */ if (host->host_failed == 0) { ourrtn = TRUE; goto leave; } /* * Either the abort wasn't appropriate, or it didn't succeed. * Now try a bus device reset. Still, look to see whether we have * multiple devices that are jammed or not - if we have multiple devices, * it makes no sense to try BUS_DEVICE_RESET - we really would need * to try a BUS_RESET instead. * * Does this make sense - should we try BDR on each device individually? * Yes, definitely. */ SCSI_LOG_ERROR_RECOVERY(3, printk("scsi_unjam_host: Checking to see if we want to try BDR\n")); for (SDpnt = host->host_queue; SDpnt; SDpnt = SDpnt->next) { for (SCloop = SDpnt->device_queue; SCloop; SCloop = SCloop->next) { if (SCloop->state == SCSI_STATE_FAILED || SCloop->state == SCSI_STATE_TIMEOUT) { break; } } if (SCloop == NULL) { continue; } /* * OK, we have a device that is having problems. Try and send * a bus device reset to it. * * FIXME(eric) - make sure we handle the case where multiple * commands to the same device have failed. They all must * get properly restarted. */ rtn = scsi_try_bus_device_reset(SCloop, RESET_TIMEOUT); if (rtn == SUCCESS) { rtn = scsi_test_unit_ready(SCloop); if (rtn == SUCCESS && scsi_unit_is_ready(SCloop)) { rtn = scsi_eh_retry_command(SCloop); if (rtn == SUCCESS) { SCloop->host->host_failed--; scsi_eh_finish_command(&SCdone, SCloop); } } } } if (host->host_failed == 0) { ourrtn = TRUE; goto leave; } /* * If we ended up here, we have serious problems. The only thing left * to try is a full bus reset. If someone has grabbed the bus and isn't * letting go, then perhaps this will help. */ SCSI_LOG_ERROR_RECOVERY(3, printk("scsi_unjam_host: Try hard bus reset\n")); /* * We really want to loop over the various channels, and do this on * a channel by channel basis. We should also check to see if any * of the failed commands are on soft_reset devices, and if so, skip * the reset. */ for (SDpnt = host->host_queue; SDpnt; SDpnt = SDpnt->next) { next_device: for (SCpnt = SDpnt->device_queue; SCpnt; SCpnt = SCpnt->next) { if (SCpnt->state != SCSI_STATE_FAILED && SCpnt->state != SCSI_STATE_TIMEOUT) { continue; } /* * We have a failed command. Make sure there are no other failed * commands on the same channel that are timed out and implement a * soft reset. */ for (SDloop = host->host_queue; SDloop; SDloop = SDloop->next) { for (SCloop = SDloop->device_queue; SCloop; SCloop = SCloop->next) { if (SCloop->channel != SCpnt->channel) { continue; } if (SCloop->state != SCSI_STATE_FAILED && SCloop->state != SCSI_STATE_TIMEOUT) { continue; } if (SDloop->soft_reset && SCloop->state == SCSI_STATE_TIMEOUT) { /* * If this device uses the soft reset option, and this * is one of the devices acting up, then our only * option is to wait a bit, since the command is * supposedly still running. * * FIXME(eric) - right now we will just end up falling * through to the 'take device offline' case. * * FIXME(eric) - It is possible that the command completed * *after* the error recovery procedure started, and if this * is the case, we are worrying about nothing here. */ scsi_sleep(1 * HZ); goto next_device; } } } /* * We now know that we are able to perform a reset for the * bus that SCpnt points to. There are no soft-reset devices * with outstanding timed out commands. */ rtn = scsi_try_bus_reset(SCpnt); if (rtn == SUCCESS) { for (SDloop = host->host_queue; SDloop; SDloop = SDloop->next) { for (SCloop = SDloop->device_queue; SCloop; SCloop = SCloop->next) { if (SCloop->channel != SCpnt->channel) { continue; } if (SCloop->state != SCSI_STATE_FAILED && SCloop->state != SCSI_STATE_TIMEOUT) { continue; } rtn = scsi_test_unit_ready(SCloop); if (rtn == SUCCESS && scsi_unit_is_ready(SCloop)) { rtn = scsi_eh_retry_command(SCloop); if (rtn == SUCCESS) { SCpnt->host->host_failed--; scsi_eh_finish_command(&SCdone, SCloop); } } /* * If the bus reset worked, but we are still unable to * talk to the device, take it offline. * FIXME(eric) - is this really the correct thing to do? */ if (rtn != SUCCESS) { printk(KERN_INFO "scsi: device set offline - not ready or command retry failed after bus reset: host %d channel %d id %d lun %d\n", SDloop->host->host_no, SDloop->channel, SDloop->id, SDloop->lun); SDloop->online = FALSE; SDloop->host->host_failed--; scsi_eh_finish_command(&SCdone, SCloop); } } } } } } if (host->host_failed == 0) { ourrtn = TRUE; goto leave; } /* * If we ended up here, we have serious problems. The only thing left * to try is a full host reset - perhaps the firmware on the device * crashed, or something like that. * * It is assumed that a succesful host reset will cause *all* information * about the command to be flushed from both the host adapter *and* the * device. * * FIXME(eric) - it isn't clear that devices that implement the soft reset * option can ever be cleared except via cycling the power. The problem is * that sending the host reset command will cause the host to forget * about the pending command, but the device won't forget. For now, we * skip the host reset option if any of the failed devices are configured * to use the soft reset option. */ for (SDpnt = host->host_queue; SDpnt; SDpnt = SDpnt->next) { next_device2: for (SCpnt = SDpnt->device_queue; SCpnt; SCpnt = SCpnt->next) { if (SCpnt->state != SCSI_STATE_FAILED && SCpnt->state != SCSI_STATE_TIMEOUT) { continue; } if (SDpnt->soft_reset && SCpnt->state == SCSI_STATE_TIMEOUT) { /* * If this device uses the soft reset option, and this * is one of the devices acting up, then our only * option is to wait a bit, since the command is * supposedly still running. * * FIXME(eric) - right now we will just end up falling * through to the 'take device offline' case. */ SCSI_LOG_ERROR_RECOVERY(3, printk("scsi_unjam_host: Unable to try hard host reset\n")); /* * Due to the spinlock, we will never get out of this * loop without a proper wait. (DB) */ scsi_sleep(1 * HZ); goto next_device2; } SCSI_LOG_ERROR_RECOVERY(3, printk("scsi_unjam_host: Try hard host reset\n")); /* * FIXME(eric) - we need to obtain a valid SCpnt to perform this call. */ rtn = scsi_try_host_reset(SCpnt); if (rtn == SUCCESS) { /* * FIXME(eric) we assume that all commands are flushed from the * controller. We should get a DID_RESET for all of the commands * that were pending. We should ignore these so that we can * guarantee that we are in a consistent state. * * I believe this to be the case right now, but this needs to be * tested. */ for (SDloop = host->host_queue; SDloop; SDloop = SDloop->next) { for (SCloop = SDloop->device_queue; SCloop; SCloop = SCloop->next) { if (SCloop->state != SCSI_STATE_FAILED && SCloop->state != SCSI_STATE_TIMEOUT) { continue; } rtn = scsi_test_unit_ready(SCloop); if (rtn == SUCCESS && scsi_unit_is_ready(SCloop)) { rtn = scsi_eh_retry_command(SCloop); if (rtn == SUCCESS) { SCpnt->host->host_failed--; scsi_eh_finish_command(&SCdone, SCloop); } } if (rtn != SUCCESS) { printk(KERN_INFO "scsi: device set offline - not ready or command retry failed after host reset: host %d channel %d id %d lun %d\n", SDloop->host->host_no, SDloop->channel, SDloop->id, SDloop->lun); SDloop->online = FALSE; SDloop->host->host_failed--; scsi_eh_finish_command(&SCdone, SCloop); } } } } } } /* * If we solved all of the problems, then let's rev up the engines again. */ if (host->host_failed == 0) { ourrtn = TRUE; goto leave; } /* * If the HOST RESET failed, then for now we assume that the entire host * adapter is too hosed to be of any use. For our purposes, however, it is * easier to simply take the devices offline that correspond to commands * that failed. */ SCSI_LOG_ERROR_RECOVERY(1, printk("scsi_unjam_host: Take device offline\n")); for (SDpnt = host->host_queue; SDpnt; SDpnt = SDpnt->next) { for (SCloop = SDpnt->device_queue; SCloop; SCloop = SCloop->next) { if (SCloop->state == SCSI_STATE_FAILED || SCloop->state == SCSI_STATE_TIMEOUT) { SDloop = SCloop->device; if (SDloop->online == TRUE) { printk(KERN_INFO "scsi: device set offline - command error recover failed: host %d channel %d id %d lun %d\n", SDloop->host->host_no, SDloop->channel, SDloop->id, SDloop->lun); SDloop->online = FALSE; } /* * This should pass the failure up to the top level driver, and * it will have to try and do something intelligent with it. */ SCloop->host->host_failed--; if (SCloop->state == SCSI_STATE_TIMEOUT) { SCloop->result |= (DRIVER_TIMEOUT << 24); } SCSI_LOG_ERROR_RECOVERY(3, printk("Finishing command for device %d %x\n", SDloop->id, SCloop->result)); scsi_eh_finish_command(&SCdone, SCloop); } } } if (host->host_failed != 0) { panic("scsi_unjam_host: Miscount of number of failed commands.\n"); } SCSI_LOG_ERROR_RECOVERY(3, printk("scsi_unjam_host: Returning\n")); ourrtn = FALSE; leave: /* * We should have a list of commands that we 'finished' during the course of * error recovery. This should be the same as the list of commands that timed out * or failed. We are currently holding these things in a linked list - we didn't * put them in the bottom half queue because we wanted to keep things quiet while * we were working on recovery, and passing them up to the top level could easily * cause the top level to try and queue something else again. * * Start by marking that the host is no longer in error recovery. */ host->in_recovery = 0; /* * Take the list of commands, and stick them in the bottom half queue. * The current implementation of scsi_done will do this for us - if need * be we can create a special version of this function to do the * same job for us. */ for (SCpnt = SCdone; SCpnt != NULL; SCpnt = SCdone) { SCdone = SCpnt->bh_next; SCpnt->bh_next = NULL; /* * Oh, this is a vile hack. scsi_done() expects a timer * to be running on the command. If there isn't, it assumes * that the command has actually timed out, and a timer * handler is running. That may well be how we got into * this fix, but right now things are stable. We add * a timer back again so that we can report completion. * scsi_done() will immediately remove said timer from * the command, and then process it. */ scsi_add_timer(SCpnt, 100, scsi_eh_times_out); scsi_done(SCpnt); } return (ourrtn); } /* * Function: scsi_error_handler * * Purpose: Handle errors/timeouts of scsi commands, try and clean up * and unjam the bus, and restart things. * * Arguments: host - host for which we are running. * * Returns: Never returns. * * Notes: This is always run in the context of a kernel thread. The * idea is that we start this thing up when the kernel starts * up (one per host that we detect), and it immediately goes to * sleep and waits for some event (i.e. failure). When this * takes place, we have the job of trying to unjam the bus * and restarting things. * */ void scsi_error_handler(void *data) { struct Scsi_Host *host = (struct Scsi_Host *) data; int rtn; DECLARE_MUTEX_LOCKED(sem); /* * We only listen to signals if the HA was loaded as a module. * If the HA was compiled into the kernel, then we don't listen * to any signals. */ if( host->loaded_as_module ) { siginitsetinv(¤t->blocked, SHUTDOWN_SIGS); } else { siginitsetinv(¤t->blocked, 0); } lock_kernel(); /* * Flush resources */ daemonize(); reparent_to_init(); /* * Set the name of this process. */ sprintf(current->comm, "scsi_eh_%d", host->host_no); host->eh_wait = &sem; host->ehandler = current; unlock_kernel(); /* * Wake up the thread that created us. */ SCSI_LOG_ERROR_RECOVERY(3, printk("Wake up parent %d\n", sem_getcount(host->eh_notify))); up(host->eh_notify); while (1) { /* * If we get a signal, it means we are supposed to go * away and die. This typically happens if the user is * trying to unload a module. */ SCSI_LOG_ERROR_RECOVERY(1, printk("Error handler sleeping\n")); /* * Note - we always use down_interruptible with the semaphore * even if the module was loaded as part of the kernel. The * reason is that down() will cause this thread to be counted * in the load average as a running process, and down * interruptible doesn't. Given that we need to allow this * thread to die if the driver was loaded as a module, using * semaphores isn't unreasonable. */ down_interruptible(&sem); if( host->loaded_as_module ) { if (signal_pending(current)) break; } SCSI_LOG_ERROR_RECOVERY(1, printk("Error handler waking up\n")); host->eh_active = 1; /* * We have a host that is failing for some reason. Figure out * what we need to do to get it up and online again (if we can). * If we fail, we end up taking the thing offline. */ if (host->hostt->eh_strategy_handler != NULL) { rtn = host->hostt->eh_strategy_handler(host); } else { rtn = scsi_unjam_host(host); } host->eh_active = 0; /* * Note - if the above fails completely, the action is to take * individual devices offline and flush the queue of any * outstanding requests that may have been pending. When we * restart, we restart any I/O to any other devices on the bus * which are still online. */ scsi_restart_operations(host); } SCSI_LOG_ERROR_RECOVERY(1, printk("Error handler exiting\n")); /* * Make sure that nobody tries to wake us up again. */ host->eh_wait = NULL; /* * Knock this down too. From this point on, the host is flying * without a pilot. If this is because the module is being unloaded, * that's fine. If the user sent a signal to this thing, we are * potentially in real danger. */ host->in_recovery = 0; host->eh_active = 0; host->ehandler = NULL; /* * If anyone is waiting for us to exit (i.e. someone trying to unload * a driver), then wake up that process to let them know we are on * the way out the door. This may be overkill - I *think* that we * could probably just unload the driver and send the signal, and when * the error handling thread wakes up that it would just exit without * needing to touch any memory associated with the driver itself. */ if (host->eh_notify != NULL) up(host->eh_notify); } /* * Function: scsi_new_reset * * Purpose: Send requested reset to a bus or device at any phase. * * Arguments: SCpnt - command ptr to send reset with (usually a dummy) * flag - reset type (see scsi.h) * * Returns: SUCCESS/FAILURE. * * Notes: This is used by the SCSI Generic driver to provide * Bus/Device reset capability. */ int scsi_new_reset(Scsi_Cmnd *SCpnt, int flag) { int rtn; switch(flag) { case SCSI_TRY_RESET_DEVICE: rtn = scsi_try_bus_device_reset(SCpnt, 0); if (rtn == SUCCESS) break; /* FALLTHROUGH */ case SCSI_TRY_RESET_BUS: rtn = scsi_try_bus_reset(SCpnt); if (rtn == SUCCESS) break; /* FALLTHROUGH */ case SCSI_TRY_RESET_HOST: rtn = scsi_try_host_reset(SCpnt); break; default: rtn = FAILED; } return rtn; } /* * Overrides for Emacs so that we follow Linus's tabbing style. * Emacs will notice this stuff at the end of the file and automatically * adjust the settings for this buffer only. This must remain at the end * of the file. * --------------------------------------------------------------------------- * Local variables: * c-indent-level: 4 * c-brace-imaginary-offset: 0 * c-brace-offset: -4 * c-argdecl-indent: 4 * c-label-offset: -4 * c-continued-statement-offset: 4 * c-continued-brace-offset: 0 * indent-tabs-mode: nil * tab-width: 8 * End: */