#ifndef _AHA152X_H #define _AHA152X_H /* * $Id: aha152x.h,v 2.5 2002/04/14 11:24:12 fischer Exp $ */ #if defined(__KERNEL__) #include #include "scsi.h" #include #include int aha152x_detect(Scsi_Host_Template *); int aha152x_command(Scsi_Cmnd *); int aha152x_queue(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *)); int aha152x_abort(Scsi_Cmnd *); int aha152x_release(struct Scsi_Host *shpnt); int aha152x_device_reset(Scsi_Cmnd *); int aha152x_bus_reset(Scsi_Cmnd *); int aha152x_host_reset(Scsi_Cmnd *); int aha152x_biosparam(Disk *, kdev_t, int*); int aha152x_proc_info(char *buffer, char **start, off_t offset, int length, int hostno, int inout); /* number of queueable commands (unless we support more than 1 cmd_per_lun this should do) */ #define AHA152X_MAXQUEUE 7 #define AHA152X_REVID "Adaptec 152x SCSI driver; $Revision: 2.5 $" /* Initial value of Scsi_Host entry */ #define AHA152X { proc_name: "aha152x", \ proc_info: aha152x_proc_info, \ name: AHA152X_REVID, \ detect: aha152x_detect, \ command: aha152x_command, \ queuecommand: aha152x_queue, \ eh_abort_handler: aha152x_abort, \ eh_device_reset_handler: aha152x_device_reset, \ eh_bus_reset_handler: aha152x_bus_reset, \ eh_host_reset_handler: aha152x_host_reset, \ release: aha152x_release, \ slave_attach: 0, \ bios_param: aha152x_biosparam, \ can_queue: 1, \ this_id: 7, \ sg_tablesize: SG_ALL, \ cmd_per_lun: 1, \ present: 0, \ unchecked_isa_dma: 0, \ use_clustering: DISABLE_CLUSTERING, \ use_new_eh_code: 1 } #endif /* port addresses */ #define SCSISEQ (HOSTIOPORT0+0x00) /* SCSI sequence control */ #define SXFRCTL0 (HOSTIOPORT0+0x01) /* SCSI transfer control 0 */ #define SXFRCTL1 (HOSTIOPORT0+0x02) /* SCSI transfer control 1 */ #define SCSISIG (HOSTIOPORT0+0x03) /* SCSI signal in/out */ #define SCSIRATE (HOSTIOPORT0+0x04) /* SCSI rate control */ #define SELID (HOSTIOPORT0+0x05) /* selection/reselection ID */ #define SCSIID SELID /* SCSI ID */ #define SCSIDAT (HOSTIOPORT0+0x06) /* SCSI latched data */ #define SCSIBUS (HOSTIOPORT0+0x07) /* SCSI data bus */ #define STCNT0 (HOSTIOPORT0+0x08) /* SCSI transfer count 0 */ #define STCNT1 (HOSTIOPORT0+0x09) /* SCSI transfer count 1 */ #define STCNT2 (HOSTIOPORT0+0x0a) /* SCSI transfer count 2 */ #define SSTAT0 (HOSTIOPORT0+0x0b) /* SCSI interrupt status 0 */ #define SSTAT1 (HOSTIOPORT0+0x0c) /* SCSI interrupt status 1 */ #define SSTAT2 (HOSTIOPORT0+0x0d) /* SCSI interrupt status 2 */ #define SCSITEST (HOSTIOPORT0+0x0e) /* SCSI test control */ #define SSTAT3 SCSITEST /* SCSI interrupt status 3 */ #define SSTAT4 (HOSTIOPORT0+0x0f) /* SCSI status 4 */ #define SIMODE0 (HOSTIOPORT1+0x10) /* SCSI interrupt mode 0 */ #define SIMODE1 (HOSTIOPORT1+0x11) /* SCSI interrupt mode 1 */ #define DMACNTRL0 (HOSTIOPORT1+0x12) /* DMA control 0 */ #define DMACNTRL1 (HOSTIOPORT1+0x13) /* DMA control 1 */ #define DMASTAT (HOSTIOPORT1+0x14) /* DMA status */ #define FIFOSTAT (HOSTIOPORT1+0x15) /* FIFO status */ #define DATAPORT (HOSTIOPORT1+0x16) /* DATA port */ #define BRSTCNTRL (HOSTIOPORT1+0x18) /* burst control */ #define PORTA (HOSTIOPORT1+0x1a) /* PORT A */ #define PORTB (HOSTIOPORT1+0x1b) /* PORT B */ #define REV (HOSTIOPORT1+0x1c) /* revision */ #define STACK (HOSTIOPORT1+0x1d) /* stack */ #define TEST (HOSTIOPORT1+0x1e) /* test register */ #define IO_RANGE 0x20 /* used in aha152x_porttest */ #define O_PORTA 0x1a /* PORT A */ #define O_PORTB 0x1b /* PORT B */ #define O_DMACNTRL1 0x13 /* DMA control 1 */ #define O_STACK 0x1d /* stack */ /* used in tc1550_porttest */ #define O_TC_PORTA 0x0a /* PORT A */ #define O_TC_PORTB 0x0b /* PORT B */ #define O_TC_DMACNTRL1 0x03 /* DMA control 1 */ #define O_TC_STACK 0x0d /* stack */ /* bits and bitmasks to ports */ /* SCSI sequence control */ #define TEMODEO 0x80 #define ENSELO 0x40 #define ENSELI 0x20 #define ENRESELI 0x10 #define ENAUTOATNO 0x08 #define ENAUTOATNI 0x04 #define ENAUTOATNP 0x02 #define SCSIRSTO 0x01 /* SCSI transfer control 0 */ #define SCSIEN 0x80 #define DMAEN 0x40 #define CH1 0x20 #define CLRSTCNT 0x10 #define SPIOEN 0x08 #define CLRCH1 0x02 /* SCSI transfer control 1 */ #define BITBUCKET 0x80 #define SWRAPEN 0x40 #define ENSPCHK 0x20 #define STIMESEL 0x18 /* mask */ #define STIMESEL_ 3 #define ENSTIMER 0x04 #define BYTEALIGN 0x02 /* SCSI signal IN */ #define SIG_CDI 0x80 #define SIG_IOI 0x40 #define SIG_MSGI 0x20 #define SIG_ATNI 0x10 #define SIG_SELI 0x08 #define SIG_BSYI 0x04 #define SIG_REQI 0x02 #define SIG_ACKI 0x01 /* SCSI Phases */ #define P_MASK (SIG_MSGI|SIG_CDI|SIG_IOI) #define P_DATAO (0) #define P_DATAI (SIG_IOI) #define P_CMD (SIG_CDI) #define P_STATUS (SIG_CDI|SIG_IOI) #define P_MSGO (SIG_MSGI|SIG_CDI) #define P_MSGI (SIG_MSGI|SIG_CDI|SIG_IOI) /* SCSI signal OUT */ #define SIG_CDO 0x80 #define SIG_IOO 0x40 #define SIG_MSGO 0x20 #define SIG_ATNO 0x10 #define SIG_SELO 0x08 #define SIG_BSYO 0x04 #define SIG_REQO 0x02 #define SIG_ACKO 0x01 /* SCSI rate control */ #define SXFR 0x70 /* mask */ #define SXFR_ 4 #define SOFS 0x0f /* mask */ /* SCSI ID */ #define OID 0x70 #define OID_ 4 #define TID 0x07 /* SCSI transfer count */ #define GETSTCNT() ( (GETPORT(STCNT2)<<16) \ + (GETPORT(STCNT1)<< 8) \ + GETPORT(STCNT0) ) #define SETSTCNT(X) { SETPORT(STCNT2, ((X) & 0xFF0000) >> 16); \ SETPORT(STCNT1, ((X) & 0x00FF00) >> 8); \ SETPORT(STCNT0, ((X) & 0x0000FF) ); } /* SCSI interrupt status */ #define TARGET 0x80 #define SELDO 0x40 #define SELDI 0x20 #define SELINGO 0x10 #define SWRAP 0x08 #define SDONE 0x04 #define SPIORDY 0x02 #define DMADONE 0x01 #define SETSDONE 0x80 #define CLRSELDO 0x40 #define CLRSELDI 0x20 #define CLRSELINGO 0x10 #define CLRSWRAP 0x08 #define CLRSDONE 0x04 #define CLRSPIORDY 0x02 #define CLRDMADONE 0x01 /* SCSI status 1 */ #define SELTO 0x80 #define ATNTARG 0x40 #define SCSIRSTI 0x20 #define PHASEMIS 0x10 #define BUSFREE 0x08 #define SCSIPERR 0x04 #define PHASECHG 0x02 #define REQINIT 0x01 #define CLRSELTIMO 0x80 #define CLRATNO 0x40 #define CLRSCSIRSTI 0x20 #define CLRBUSFREE 0x08 #define CLRSCSIPERR 0x04 #define CLRPHASECHG 0x02 #define CLRREQINIT 0x01 /* SCSI status 2 */ #define SOFFSET 0x20 #define SEMPTY 0x10 #define SFULL 0x08 #define SFCNT 0x07 /* mask */ /* SCSI status 3 */ #define SCSICNT 0xf0 /* mask */ #define SCSICNT_ 4 #define OFFCNT 0x0f /* mask */ /* SCSI TEST control */ #define SCTESTU 0x08 #define SCTESTD 0x04 #define STCTEST 0x01 /* SCSI status 4 */ #define SYNCERR 0x04 #define FWERR 0x02 #define FRERR 0x01 #define CLRSYNCERR 0x04 #define CLRFWERR 0x02 #define CLRFRERR 0x01 /* SCSI interrupt mode 0 */ #define ENSELDO 0x40 #define ENSELDI 0x20 #define ENSELINGO 0x10 #define ENSWRAP 0x08 #define ENSDONE 0x04 #define ENSPIORDY 0x02 #define ENDMADONE 0x01 /* SCSI interrupt mode 1 */ #define ENSELTIMO 0x80 #define ENATNTARG 0x40 #define ENSCSIRST 0x20 #define ENPHASEMIS 0x10 #define ENBUSFREE 0x08 #define ENSCSIPERR 0x04 #define ENPHASECHG 0x02 #define ENREQINIT 0x01 /* DMA control 0 */ #define ENDMA 0x80 #define _8BIT 0x40 #define DMA 0x20 #define WRITE_READ 0x08 #define INTEN 0x04 #define RSTFIFO 0x02 #define SWINT 0x01 /* DMA control 1 */ #define PWRDWN 0x80 #define STK 0x07 /* mask */ /* DMA status */ #define ATDONE 0x80 #define WORDRDY 0x40 #define INTSTAT 0x20 #define DFIFOFULL 0x10 #define DFIFOEMP 0x08 /* BURST control */ #define BON 0xf0 #define BOFF 0x0f /* TEST REGISTER */ #define BOFFTMR 0x40 #define BONTMR 0x20 #define STCNTH 0x10 #define STCNTM 0x08 #define STCNTL 0x04 #define SCSIBLK 0x02 #define DMABLK 0x01 /* On the AHA-152x board PORTA and PORTB contain some information about the board's configuration. */ typedef union { struct { unsigned reserved:2; /* reserved */ unsigned tardisc:1; /* Target disconnect: 0=disabled, 1=enabled */ unsigned syncneg:1; /* Initial sync neg: 0=disabled, 1=enabled */ unsigned msgclasses:2; /* Message classes 0=#4 1=#0, #1, #2, #3, #4 2=#0, #3, #4 3=#0, #4 */ unsigned boot:1; /* boot: 0=disabled, 1=enabled */ unsigned dma:1; /* Transfer mode: 0=PIO; 1=DMA */ unsigned id:3; /* SCSI-id */ unsigned irq:2; /* IRQ-Channel: 0,3=12, 1=10, 2=11 */ unsigned dmachan:2; /* DMA-Channel: 0=0, 1=5, 2=6, 3=7 */ unsigned parity:1; /* SCSI-parity: 1=enabled 0=disabled */ } fields; unsigned short port; } aha152x_config ; #define cf_parity fields.parity #define cf_dmachan fields.dmachan #define cf_irq fields.irq #define cf_id fields.id #define cf_dma fields.dma #define cf_boot fields.boot #define cf_msgclasses fields.msgclasses #define cf_syncneg fields.syncneg #define cf_tardisc fields.tardisc #define cf_port port /* Some macros to manipulate ports and their bits */ #define SETPORT(PORT, VAL) outb( (VAL), (PORT) ) #define GETPORT(PORT) inb( PORT ) #define SETBITS(PORT, BITS) outb( (inb(PORT) | (BITS)), (PORT) ) #define CLRBITS(PORT, BITS) outb( (inb(PORT) & ~(BITS)), (PORT) ) #define TESTHI(PORT, BITS) ((inb(PORT) & (BITS)) == (BITS)) #define TESTLO(PORT, BITS) ((inb(PORT) & (BITS)) == 0) #define SETRATE(RATE) SETPORT(SCSIRATE,(RATE) & 0x7f) #if defined(AHA152X_DEBUG) enum { debug_procinfo = 0x0001, debug_queue = 0x0002, debug_locks = 0x0004, debug_intr = 0x0008, debug_selection = 0x0010, debug_msgo = 0x0020, debug_msgi = 0x0040, debug_status = 0x0080, debug_cmd = 0x0100, debug_datai = 0x0200, debug_datao = 0x0400, debug_eh = 0x0800, debug_done = 0x1000, debug_phases = 0x2000, }; #endif #endif /* _AHA152X_H */